loose handlebars
#1
Senior Member
Thread Starter
Join Date: Apr 2008
Posts: 179
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
loose handlebars
alright, so i tighten my stem with my handlebars at a 90 degree angle to the floor. After a few bunnyhops, i notice that the handlebar slowly moves back, to the point where it almost hits my knees (then wont go any further back). What ive noticed about the handlebars is that at the part where the stem locks onto it, it's kinda squeezed into an odd shape. Is it time for new handlebars? new stem? or is there something i can do?
i already tried cutting an old tube out and wrapping it around the handlebars, but even with the stem fully tightened, it moves alot
btw, the parts i described are the stock GT stem and stock GT handlebars.
i already tried cutting an old tube out and wrapping it around the handlebars, but even with the stem fully tightened, it moves alot
btw, the parts i described are the stock GT stem and stock GT handlebars.
#2
Eastern or Go Home
Join Date: Nov 2008
Location: Visalia
Posts: 68
Bikes: 2001-2002 Eastern Jane(Dont make anymore)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I have had this problem before. The reason mine ovaled/bent in is because the inside had bad rust, causing it to bend when i tightened the stem. Over tightening could cause it too, with or without rust. I reccomend buying new handlebars.
#3
Senior Member
Thread Starter
Join Date: Apr 2008
Posts: 179
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
how would i know if im over tightening?
i dont have a torque wrench, and they dont really make them for the allen bolt styles, do they?
i dont have a torque wrench, and they dont really make them for the allen bolt styles, do they?
#4
Senior Member
Join Date: Dec 2006
Location: Manorville, NY
Posts: 256
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I had the same problem. The bike shop took the paint off my handelbars, then it never happened again. Take a flathead screwdriver, and put cuts in your stem going diagonally. Alot of them, some deep. Then if they still move, get new handelbars.
#5
Senior Member
Thread Starter
Join Date: Apr 2008
Posts: 179
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
is there another thing i can do besides that?
like maybe some sort of material that could be stuffed in there to keep it nice and snug.
like maybe some sort of material that could be stuffed in there to keep it nice and snug.
#7
Senior Member
Join Date: Dec 2006
Location: Manorville, NY
Posts: 256
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Is your stem really smooth inside? Are your handelbars really smooth where they meet the stem? Or are they rough to keep them from moving.
#8
i bunnyhopped your mom
Join Date: Sep 2008
Location: your mom's place
Posts: 162
Bikes: Mongoose Raid, 2 mole yoro's, and a Diamondback Grind
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
yeah, mine were completely smooth a while back. I actually bought it used, then tried DJ. that's how I learned abotu the slipping bars. bad results, lol. just buy a new set, and wipe the inside of your stem out. the bits of metal that had worn off my bars made a kind of sludge in there. make sure it's gone.
#11
Eastern or Go Home
Join Date: Nov 2008
Location: Visalia
Posts: 68
Bikes: 2001-2002 Eastern Jane(Dont make anymore)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
The handle bars should have a cross-thatch section, or a section where it has grooves for the stem to tighten down on to.
#12
Senior Member
Thread Starter
Join Date: Apr 2008
Posts: 179
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
nope. i guess it's time for me to install my new handlebars once i get a new stem, unless someone has another solution for me.
#13
We win all charity rides
Join Date: Apr 2008
Location: Central Michigan University/ GR, MI
Posts: 3,369
Bikes: BMX, fixed gear
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
try rubber. like cut some rubberbands and wrap em around the inside. just a temporary fix though. wont last more than a week or two depending on how hard you ride
#14
Senior Member
Thread Starter
Join Date: Apr 2008
Posts: 179
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
hmm, rubber bands sounds good.
i was sitting here thinking of how to fix it, and how well would cement work? or super glue?
i was sitting here thinking of how to fix it, and how well would cement work? or super glue?
#15
Your imaginary friend.
Join Date: Jul 2007
Location: Wandering aimlessly.
Posts: 2,211
Bikes: A sweet Quamen ATL custom, GT Mach 2
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Super glue? No
Cement? wtf
Caulk? Maybe
Hot glue? Maybe
They'd end up wearing out fast though.
Cement? wtf
Caulk? Maybe
Hot glue? Maybe
They'd end up wearing out fast though.
__________________
Every passing minute is another chance to turn it all around.
Every passing minute is another chance to turn it all around.
#16
free mallocs
Join Date: Jan 2008
Location: melbourne, australia
Posts: 520
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#17
Eastern or Go Home
Join Date: Nov 2008
Location: Visalia
Posts: 68
Bikes: 2001-2002 Eastern Jane(Dont make anymore)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
WOAH! No glue ever lol. And cement? You nuts? Thats as bad as me using a hammer on my bike >.< Possibly worse.
Get some rough ass sand paper and sand your stem and bars untill its really rough. That should buy you some time.
Get some rough ass sand paper and sand your stem and bars untill its really rough. That should buy you some time.
#18
Senior Member
Thread Starter
Join Date: Apr 2008
Posts: 179
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
alright, i will start sanding the handlebars, do i sand the inside of the stem too?
and also, im looking to buy a new stem right now, are all stems supposed to have the grooves to match the handlebar? or is it just the cheap stems that are smooth on the inside?
and also, im looking to buy a new stem right now, are all stems supposed to have the grooves to match the handlebar? or is it just the cheap stems that are smooth on the inside?
#19
Eastern or Go Home
Join Date: Nov 2008
Location: Visalia
Posts: 68
Bikes: 2001-2002 Eastern Jane(Dont make anymore)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I only suggest sanding because it should be kinda rough on your handlebars where the stem grabs it. Not sure about inside my stem, dont have allen keys on me right now to check...pretty sure mine hase diagonal "cuts" in it.
#20
Change=inevitable. ?=+/-
Join Date: Jul 2007
Location: Sugar Land, TX
Posts: 295
Bikes: MTB, 700c commuter, BMX
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Here is what me and my buds did when we were too broke to buy new parts:
Get a coke can and cut out a square as wide as the stem. Then fold this square once, making a rectangle. Install it between the stem and handle bars...and if that doesn't solve the issue, then repeat this for the opposing side of the stem/bars.
***I am not responsible for any damages to you or your property***
Might buy you some time or even solve the issue. I did this on a bike when i rode hard and all it required was an adjustment every month or so.
Get a coke can and cut out a square as wide as the stem. Then fold this square once, making a rectangle. Install it between the stem and handle bars...and if that doesn't solve the issue, then repeat this for the opposing side of the stem/bars.
***I am not responsible for any damages to you or your property***
Might buy you some time or even solve the issue. I did this on a bike when i rode hard and all it required was an adjustment every month or so.
#22
Senior Member
Thread Starter
Join Date: Apr 2008
Posts: 179
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Alright, i tried the soda can trick, but handlebar still moved after a few bunnyhops.
I think it's because the part where the stem locks onto is squeezed smaller from over tightening or something.
I think it's because the part where the stem locks onto is squeezed smaller from over tightening or something.
#23
member
Join Date: Oct 2004
Location: San Jose, CA
Posts: 4,751
Bikes: Solid AA
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Your first problem is that you're putting your bars perpendicular to the ground, rather than parallel with your forks and steerer.
#24
i bunnyhopped your mom
Join Date: Sep 2008
Location: your mom's place
Posts: 162
Bikes: Mongoose Raid, 2 mole yoro's, and a Diamondback Grind
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
the starting angle has nothing to do with it. I align my bars by using the ground, not my fork and they're fine. just buy new bars.
#25
member
Join Date: Oct 2004
Location: San Jose, CA
Posts: 4,751
Bikes: Solid AA
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
That's the angle he's riding his bars at, not simply the starting angle, if I'm reading it correctly.