Installing pegs
#1
Senior Member
Thread Starter
Join Date: Aug 2008
Location: Tucson, Arizona
Posts: 704
Bikes: '02 Lemond Buenos Aires, '98 Fuji Touring w/ Shimano Nexus premium, '06 Jamis Nova 853 cross frame set up as commuter, '03 Fuji Roubaix Pro 853 back up training bike
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Installing pegs
Most of the BMX bikes I build come with either threaded or unthreaded pegs. Should I always install the peg, then the axle nut for both threaded and unthreaded, or can I install the axle nut, then peg for the threaded pegs?
#2
Senior Member
Join Date: Apr 2009
Location: near Pittsburgh, PA
Posts: 105
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
With the threaded ones, install the nut first, then the peg. You can take them off and on easier, but they are not as strong and if they come loose at all, they will bend the axle. Bolt on are much better.
#3
Senior Member
Thread Starter
Join Date: Aug 2008
Location: Tucson, Arizona
Posts: 704
Bikes: '02 Lemond Buenos Aires, '98 Fuji Touring w/ Shimano Nexus premium, '06 Jamis Nova 853 cross frame set up as commuter, '03 Fuji Roubaix Pro 853 back up training bike
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Thanks for the info. I have a hard time installing threadless pegs on many bikes. The large contact surface between the peg and dropout seems to induce axle creep, throwing off the alignment and screwing up the chain tension. I've tried applying grease to the dropout/peg surfaces, and slowly tightening the axle bolts, alternating them, and I can get it, but it takes many trials. Sometimes I use the long, padded handle of a Park pedal wrench wedges between the tire and the seat tube to put back pressure on the wheel to keep it from creeping forward.
#4
member
Join Date: Oct 2004
Location: San Jose, CA
Posts: 4,751
Bikes: Solid AA
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Terrible advice. With threaded pegs, only install the peg, because it takes the place of the axle nut. Putting a nut between the peg and dropout gives the peg extra leverage.
Don't apply grease between the peg and dropout, because that's just going to induce axle creep via lubrication of a surface that's already sliding.
Flip the bike over, step on the back tire, and tighten down the non-peg side enough so that it's somewhat locked, then pull back on the peg to straighten the wheel out while tightening that side all the way down, and then lock out the non-peg side.
edit: Do they even have threaded pegs on anything but Walmart bikes anymore?
I have a hard time installing threadless pegs on many bikes. The large contact surface between the peg and dropout seems to induce axle creep, throwing off the alignment and screwing up the chain tension. I've tried applying grease to the dropout/peg surfaces, and slowly tightening the axle bolts, alternating them, and I can get it, but it takes many trials.
edit: Do they even have threaded pegs on anything but Walmart bikes anymore?
Last edited by CMcMahon; 01-04-10 at 11:32 AM.
#5
Senior Member
Join Date: Sep 2009
Location: Lafayette, IN
Posts: 76
Bikes: Colnago Dream CX, Gary Fisher XCal, Diamondback Haanjo
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I can't imagine. In fact, I don't even think walmart pegs are threaded any more. Which raises a valid point to the OP - don't put threaded pegs on anything. ever. It's like pleading for bent axles and stripped threads. Use un-threaded pegs, without a washer, and with a tensioner if you're worried about it slipping. At least, thats what I've found to be the best course of action over the years.
#6
Senior Member
Thread Starter
Join Date: Aug 2008
Location: Tucson, Arizona
Posts: 704
Bikes: '02 Lemond Buenos Aires, '98 Fuji Touring w/ Shimano Nexus premium, '06 Jamis Nova 853 cross frame set up as commuter, '03 Fuji Roubaix Pro 853 back up training bike
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Terrible advice. With threaded pegs, only install the peg, because it takes the place of the axle nut. Putting a nut between the peg and dropout gives the peg extra leverage.
Don't apply grease between the peg and dropout, because that's just going to induce axle creep via lubrication of a surface that's already sliding.
Flip the bike over, step on the back tire, and tighten down the non-peg side enough so that it's somewhat locked, then pull back on the peg to straighten the wheel out while tightening that side all the way down, and then lock out the non-peg side.
edit: Do they even have threaded pegs on anything but Walmart bikes anymore?
Don't apply grease between the peg and dropout, because that's just going to induce axle creep via lubrication of a surface that's already sliding.
Flip the bike over, step on the back tire, and tighten down the non-peg side enough so that it's somewhat locked, then pull back on the peg to straighten the wheel out while tightening that side all the way down, and then lock out the non-peg side.
edit: Do they even have threaded pegs on anything but Walmart bikes anymore?
We had a TON of pegs on boxes. The previous bike tech avoided installing them either because they were a pain, or because they made the bikes harder to put in and take out of the display racks. We had far more unthreaded pegs than threaded.
Thread
Thread Starter
Forum
Replies
Last Post
mastershake916
Bicycle Mechanics
18
06-07-14 08:22 AM