Go Back  Bike Forums > Bike Forums > Classic & Vintage
Reload this Page >

Uniglide lockring removal without tool?

Notices
Classic & Vintage This forum is to discuss the many aspects of classic and vintage bicycles, including musclebikes, lightweights, middleweights, hi-wheelers, bone-shakers, safety bikes and much more.

Uniglide lockring removal without tool?

Old 07-13-17, 10:57 PM
  #1  
Senior Member
Thread Starter
 
zammykoo's Avatar
 
Join Date: Jun 2015
Location: Houston, TX
Posts: 433

Bikes: Trek 510, Dahon Classic III, Specialized Tricross, Raleigh Technium 460

Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 122 Post(s)
Liked 7 Times in 4 Posts
Uniglide lockring removal without tool?

I don't have the correct removal tool so before I place an order, does anyone have tips on removing it without chewing it up too much? This is for my clunker build so I am hoping to be able to use the wheelset. The freewheel is just really crunchy when I spin it so I wanted to remove it, spray it down, and lube it. Thank ya.

For reference:
https://i.imgur.com/roQuit4.jpg
zammykoo is offline  
Old 07-13-17, 11:13 PM
  #2  
Stop reading my posts!
 
unworthy1's Avatar
 
Join Date: Sep 2004
Posts: 12,958
Mentioned: 89 Post(s)
Tagged: 0 Thread(s)
Quoted: 1421 Post(s)
Liked 1,038 Times in 769 Posts
chain-whips, 2 of them, are all you need. If you don't have then borrow 2 for a half hour, max. You won't have to use them to re-install afterward.

EDIT, sorry but did not see the pic when Iadvised you , it IS a freewheel and not a UG cassette, so the chainwhips will do nothing (unless you want to take sprockets off the FW body). You need the FW tool to remove it, as others have said... then you can soak it in a can or solvent (try 50-50 acetone and ATF) then drain-dry and re-lube with liquid lube.

Last edited by unworthy1; 07-15-17 at 12:53 AM.
unworthy1 is offline  
Old 07-13-17, 11:22 PM
  #3  
Senior Member
 
ramzilla's Avatar
 
Join Date: Dec 2014
Location: Fernandina Beach FL
Posts: 3,605

Bikes: Vintage Japanese Bicycles, Tange, Ishiwata, Kuwahara

Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 700 Post(s)
Liked 321 Times in 251 Posts
Maybe two big ass pipe wrenches. Or, one big ass pipe wrench and a big ass set of chanellocks. Really. The easiest way to get one off is this: Get an old sacrificial chain. (put on some work gloves) Wrap chain around big cog. Turn wheel upside down & clamp chain down in a big f#$%^n vise. Now, hit that small cog wit a big ass pipe wrench. Or, a chain whip tool if you got one. You'll figure it out sooner or later. Be good. Have fun.
ramzilla is offline  
Old 07-14-17, 02:42 AM
  #4  
Senior Member
 
Join Date: Mar 2008
Posts: 8,688
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1074 Post(s)
Liked 295 Times in 222 Posts
"Lockring" usually refers to the part that holds a cassette onto the freehub body.
UG freehubs AFAIK don't have lockrings. They use the smallest sprocket to thread onto the FH body and hold the rest of the stack in Place.
If yours is crunchy, removing the cassette won't do squat. That's not where the action is.


So don't go looking for cassette whips to borrow.


The splined center cavity of yours look like on a freewheel. But freewheels generally do have a lockring holding the sprockets in Place.


So I assume the part you want to remove is the ring with the lettering on.
The correct tool would be a pin wrench. Something like this.117.B | Facom 100mm Pin Wrench 245 mm Chrome | Facom
If you have some metal stock, it's not that hard to make a crude one.
Success is largely dependent on how stuck things are.
Don't get your hope up.
Some have managed removal with a drift punch.
It's cheap enough to try.
Can't advise on thread direction.
Freewheels generally aren't very well sealed on the inside.
If it was me, I'd put the Wheel flat, then shoot WD-40 at/through the gap between stationary and moving parts until it begins to run off Clean.
Then add some runny oil and call it a day.
dabac is offline  
Old 07-14-17, 05:28 AM
  #5  
Senior Member
 
IthaDan's Avatar
 
Join Date: Jan 2012
Location: Ithaca, NY
Posts: 4,915

Bikes: Click on the #YOLO

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 26 Post(s)
Likes: 0
Liked 12 Times in 12 Posts
Sheldon Brown has a method I can't quite wrap my head around in his heroic repairs section:

https://www.sheldonbrown.com/heroic-repairs.html

Originally Posted by Sheldon brown's site
Removing sprockets without a tool.

With a freewheel or older cassette, the outer one, sometimes more, sprockets are threaded on. Chain whips are usually not necessary to remove them, except on the oldest freewheels which have sprockets that remove to the inside.
Place the chain on the smallest front sprocket, and remove the chain from the rear derailer. A SRAM chain with a PowerLink can easily be disconnected. With another chain, you may have to remove the lower (tension) pulley of the rear derailer to extract the chain.

With the right pedal behind top position (around 10 o'clock), wrap the lower of chain around the bottom of the outermost outer sprocket and the upper run around an inner sprocket. The closer the two sprockets are in size the better this works. Get as much slack out of the chain as you can. If you haven't disconnected the chain, shape it into a figure-8 behind the sprockets.

Now step down on the right pedal, backpedaling. Because the outer sprocket is smaller, it will turn faster and unscrew. You may have to reposition the chain once or twice before the sprocket is completely loose.

Repeat as necessary to remove additional sprockets until you reach a splined sprocket and can lift the rest of the sprockets off. Be sure to keep all sprockets and spacers in order for replacement.
__________________

Shimano : Click :: Campy : Snap :: SRAM : Bang
IthaDan is offline  
Old 07-14-17, 05:54 AM
  #6  
Senior Member
 
jcb3's Avatar
 
Join Date: Sep 2014
Location: Irvine, CA
Posts: 611
Mentioned: 29 Post(s)
Tagged: 0 Thread(s)
Quoted: 140 Post(s)
Likes: 0
Liked 13 Times in 12 Posts
Photo looks more like a freewheel than a freehub.

I'd suggest you try flushing it with a light oil and solvent first, rather than taking it apart. That will usually work. Disassembly invloves getting a gazillion little balls and little pawls + springs all over the place, if you aren't careful.

Maybe consider a new one. The cheap ones on amazon aren't bad for a clunker, and if you get a new chain, you could have skipping problems with the worn freewheel.
jcb3 is offline  
Old 07-14-17, 07:06 AM
  #7  
Senior Member
 
Join Date: Dec 2005
Posts: 17,127
Mentioned: 480 Post(s)
Tagged: 0 Thread(s)
Quoted: 3788 Post(s)
Liked 6,573 Times in 2,580 Posts
^ ditto. If that photo is of the item in question, it's a freewheel.
nlerner is offline  
Old 07-14-17, 07:16 AM
  #8  
Senior Member
 
Velocivixen's Avatar
 
Join Date: Oct 2013
Location: The Great Pacific Northwest
Posts: 4,525
Mentioned: 87 Post(s)
Tagged: 0 Thread(s)
Quoted: 400 Post(s)
Liked 37 Times in 26 Posts
It's a freewheel. Park Tool sells the splined tool that goes inside there. They're around $6 where I live.
Unless you wish to dismantle the freewheel, do not get a pin spanner to unscrew the top race where the two little divots are. I just happen to like to disassemble freewheels and have done it many, many times. I wait to get the freewheel off the hub first. Although I have disassembled, de-greased, put new ball bearings, top & bottom, while the freewheel was still attatched.
It is not for the impatient. It helps to have small fingers and a steady hand.
Velocivixen is offline  
Old 07-14-17, 12:00 PM
  #9  
Old fart
 
JohnDThompson's Avatar
 
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,935

Bikes: Several, mostly not name brands.

Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3571 Post(s)
Liked 3,367 Times in 1,916 Posts
Originally Posted by Velocivixen


It's a freewheel. Park Tool sells the splined tool that goes inside there. They're around $6 where I live.
Agreed. The Park FR-1, Bicycle Research CT-6, or Shimano TL-FW30 will remove it from the hub. The Park and Bicycle Research versions are usually under US$10, the Shimano a bit more.
JohnDThompson is offline  
Old 07-14-17, 12:11 PM
  #10  
Senior Member
Thread Starter
 
zammykoo's Avatar
 
Join Date: Jun 2015
Location: Houston, TX
Posts: 433

Bikes: Trek 510, Dahon Classic III, Specialized Tricross, Raleigh Technium 460

Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 122 Post(s)
Liked 7 Times in 4 Posts
Yeah, the FR-1 is what I need and was planning to order. I checked a nearby REI and Performance Bike and neither had it, so I'd have to order one or go further into town to an LBS. I have the FR-5 tool but didn't realize this was a different design until I tried fitting it on last night.

I also have a chain whip so I'm going to give that a try today. Thanks all for the tips!
zammykoo is offline  
Old 07-14-17, 01:06 PM
  #11  
Senior Member
 
Join Date: Mar 2008
Posts: 8,688
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1074 Post(s)
Liked 295 Times in 222 Posts
Originally Posted by zammykoo
Yeah, the FR-1 is what I need and was planning to order. I checked a nearby REI and Performance Bike and neither had it, so I'd have to order one or go further into town to an LBS. I have the FR-5 tool but didn't realize this was a different design until I tried fitting it on last night.

I also have a chain whip so I'm going to give that a try today. Thanks all for the tips!
The freewheel puller will remove the freewheel off the hub. Makes flushing it less messy, but does not expose the innards.
Chain whips will remove the sprockets from the core, but will not expose the innards.
dabac is offline  
Old 07-14-17, 02:16 PM
  #12  
Senior Member
 
67tony's Avatar
 
Join Date: Feb 2012
Location: Williamsburg, VA Sebastian, FL
Posts: 1,373

Bikes: 1987 Centurion Ironman Master, 1992 Koga Miyata Exerciser, 1992 Schwinn Crosscut

Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 209 Post(s)
Likes: 0
Liked 174 Times in 91 Posts
I know it's frowned upon, but I've cut a portion out of the top of a milk jug, put in about an inch of gasoline, followed by the freewheel, then swirled it around for a few days, once in a while taking it out and spinning it. After that, and several days of spinning and drying, I work in some Tenacious Oil. The result is a very smooth, and very quiet, freewheel.

(PS: I also collect and take the dirty gas to a oil change place for proper disposal...)

Last edited by 67tony; 07-14-17 at 02:20 PM.
67tony is offline  
Old 07-14-17, 09:41 PM
  #13  
Senior Member
 
cyclodan's Avatar
 
Join Date: Feb 2004
Location: S.E. Mi.
Posts: 287
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 1 Time in 1 Post
[QUOTE=67tony;19719337]... After that, and several days of spinning and drying, I work in some Tenacious Oil. The result is a very smooth, and very quiet, freewheel...


+1 on the Phil's Tenacious!
cyclodan is offline  
Old 07-15-17, 06:18 AM
  #14  
Freewheel Medic
 
pastorbobnlnh's Avatar
 
Join Date: Oct 2005
Location: An Island on the Coast of GA!
Posts: 12,878

Bikes: Snazzy* Schwinns, Classy Cannondales & a Super Pro Aero Lotus (* Ed.)

Mentioned: 140 Post(s)
Tagged: 0 Thread(s)
Quoted: 1448 Post(s)
Liked 2,177 Times in 957 Posts
Or remove it, and properly service it. It's the only mechanical part on a vintage bicycle (the rest are simple axles with or without bearings).

"Drip--- spin--- drip"
is only a temporary solution and doesn't effectively remove contaminants such as dust, grit, rust, the dried out original grease, or bad ball bearings. Also, the oil does not last as long as a proper grease nor does it protect the internals from future contamination.

Would you "Drip--- spin--- drip" on your BB, your headset or your wheel axles? Of course not!







__________________
Bob
Enjoying the GA coast all year long!

Thanks for visiting my website: www.freewheelspa.com





pastorbobnlnh is offline  
Old 07-15-17, 07:24 AM
  #15  
Old fart
 
JohnDThompson's Avatar
 
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,935

Bikes: Several, mostly not name brands.

Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3571 Post(s)
Liked 3,367 Times in 1,916 Posts
Originally Posted by 67tony
I know it's frowned upon, but I've cut a portion out of the top of a milk jug, put in about an inch of gasoline, followed by the freewheel, then swirled it around for a few days, once in a while taking it out and spinning it. After that, and several days of spinning and drying, I work in some Tenacious Oil. The result is a very smooth, and very quiet, freewheel.

(PS: I also collect and take the dirty gas to a oil change place for proper disposal...)
You're right. Using gasoline as a degreaser is not considered to be Good Practice. Odorless mineral spirits work just as well as gasoline for degreasing, far less dangerous (no explosion hazard), and can be reused by simply allowing the particulate matter to settle out and then decanting the clean spirits off the top.
JohnDThompson is offline  
Old 07-15-17, 07:26 AM
  #16  
Old fart
 
JohnDThompson's Avatar
 
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,935

Bikes: Several, mostly not name brands.

Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3571 Post(s)
Liked 3,367 Times in 1,916 Posts
Originally Posted by pastorbobnlnh
Would you "Drip--- spin--- drip" on your BB, your headset or your wheel axles? Of course not!
Unless it's a Sturmey-Archer hub, anyway.
JohnDThompson is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
c4p
Bicycle Mechanics
4
07-27-17 09:54 PM
Loose Chain
Bicycle Mechanics
7
04-03-16 10:30 AM
illdthedj
Bicycle Mechanics
24
06-10-12 03:04 PM
TromboneAl
Bicycle Mechanics
20
04-15-12 04:31 PM
T_Le
Bicycle Mechanics
7
08-13-11 09:11 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.