Go Back  Bike Forums > Bike Forums > Classic & Vintage
Reload this Page >

ISO and for trade thread part 5

Notices
Classic & Vintage This forum is to discuss the many aspects of classic and vintage bicycles, including musclebikes, lightweights, middleweights, hi-wheelers, bone-shakers, safety bikes and much more.

ISO and for trade thread part 5

Old 01-27-24, 01:56 PM
  #6401  
Senior Member
 
Join Date: Jun 2021
Posts: 1,802

Bikes: '38 Schwinn New World, ’69 Peugeot PX-10, '72 Peugeot PX-10, ‘7? Valgan, '78 Raleigh Comp GS, ’79 Holdsworth Pro, ’80 Peugeot TH-8 tandem, '87 Trek 400T, ‘7? Raleigh Sports, ‘7? Raleigh Superbe, ‘6? Hercules

Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 749 Post(s)
Liked 1,501 Times in 733 Posts
ISO Campy Record front hub 32h..

Anyone have a decent 32h front Campy hub..? [edit- low flange]
May have an odd or end to trade..

Last edited by ehcoplex; 01-27-24 at 03:11 PM.
ehcoplex is offline  
Old 01-27-24, 02:41 PM
  #6402  
Full Member
 
Portlandjim's Avatar
 
Join Date: May 2023
Location: Big Sur California
Posts: 208

Bikes: 1946 Holdsworth Cyclone, 1969 Cinelli SC, 1972 Raleigh Pro, 1973 Merz road bike, 1974 Alex Singer Sportif, 1974 Merz track bike, 1975 Teledyne Titan, 1976 Ritchey road bike, 1977 DiNucci built Merz track bike, 1977 (?) Exxon Graftek, many more!

Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 135 Post(s)
Liked 1,384 Times in 167 Posts
Campy front hub?

Originally Posted by ehcoplex
Anyone have a decent 32h front Campy hub..?
May have an odd or end to trade..
High flange or low?

Jim Merz
Portlandjim is offline  
Old 01-27-24, 03:11 PM
  #6403  
Senior Member
 
Join Date: Jun 2021
Posts: 1,802

Bikes: '38 Schwinn New World, ’69 Peugeot PX-10, '72 Peugeot PX-10, ‘7? Valgan, '78 Raleigh Comp GS, ’79 Holdsworth Pro, ’80 Peugeot TH-8 tandem, '87 Trek 400T, ‘7? Raleigh Sports, ‘7? Raleigh Superbe, ‘6? Hercules

Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 749 Post(s)
Liked 1,501 Times in 733 Posts
Originally Posted by Portlandjim
High flange or low?

Jim Merz
Low. Funny, as I was posting I was thinking 'am I leaving out something...?' And that was it. Editing now...
ehcoplex is offline  
Old 01-27-24, 03:52 PM
  #6404  
Senior Member
 
Join Date: May 2019
Location: Bloomington, IN
Posts: 2,894

Bikes: Paramount, Faggin, Ochsner, Ciocc, Basso

Mentioned: 114 Post(s)
Tagged: 0 Thread(s)
Quoted: 1265 Post(s)
Liked 1,762 Times in 1,076 Posts
I'm guessing you want NR?

How nice? Proposal for trade? Or how deep are your pockets?
Mad Honk is offline  
Old 01-27-24, 04:31 PM
  #6405  
Senior Member
 
Join Date: Jun 2021
Posts: 1,802

Bikes: '38 Schwinn New World, ’69 Peugeot PX-10, '72 Peugeot PX-10, ‘7? Valgan, '78 Raleigh Comp GS, ’79 Holdsworth Pro, ’80 Peugeot TH-8 tandem, '87 Trek 400T, ‘7? Raleigh Sports, ‘7? Raleigh Superbe, ‘6? Hercules

Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 749 Post(s)
Liked 1,501 Times in 733 Posts
Originally Posted by Mad Honk
I'm guessing you want NR?

How nice? Proposal for trade? Or how deep are your pockets?
Deep pockets, hmmmmm. Has me wondering, are these rare? I've got a set of 32h 650b rims, and a Campy 32h record rear hub, but no front to go with it. Wanting to build up the wheels for the Comp GS I recently acquired, but trying to keep the $ under control. If these are a 'hen's teeth' item I may have to rethink!
ehcoplex is offline  
Old 01-29-24, 05:39 PM
  #6406  
Full Member
 
VintageSteelEU's Avatar
 
Join Date: May 2021
Location: London
Posts: 492

Bikes: Motobecane C41, Matsu$hita Nashonaru

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 194 Post(s)
Liked 343 Times in 209 Posts
Looking for a clamp for these:


Suntour Superbe / Sprint top mounted power shifters

The frame I want them on doesn't have braze-on shifter bosses. I don't mind actually mounting them using the gizmo they are on, but I think I'd rather have them mounted the usual way, using a standard clamp. As last resort, I can get shifter bosses brazed on the downtube, but I think I'd rather just use a standard clamp. From what I can see, clamp from chunky power shifters is not going to work, nor one made for Vx shifters. It has to be a kind of clamp where the shifter limiting bosses / cable guides can be removed. I think Cyclone paint-stripper clamp could be a good candidate, maybe some others. I have some stuff for trade, depending what you might need.
VintageSteelEU is offline  
Old 01-31-24, 08:24 PM
  #6407  
Señor Member
 
USAZorro's Avatar
 
Join Date: Oct 2004
Location: Hardy, VA
Posts: 17,924

Bikes: Mostly English - predominantly Raleighs

Mentioned: 70 Post(s)
Tagged: 0 Thread(s)
Quoted: 1485 Post(s)
Liked 1,053 Times in 626 Posts
Whoo-hoo! It has found a good home.

Going to try it this way. This is a nice frame in very good condition in a beautiful color. It's essentially my size, but despite being pretty cool, I'm just not going to get to it.

It's a 1996 Schwinn Passage. Seat tube is 21" ctt, Seat tube extends an additional inch beyond that. Top tube is 22"" ctc. Rear spacing is 130mm. It comes with what you see here. Headset and Bottom bracket both need service, and the seatpost clamp is missing.

I've tried to sell it for $35.00 plus shipping, but it remains here. I'm open to trades. I'm not limiting myself to this, but a pair of decent, alloy 700c or 27" wheels or rims (36 hole please) could make this yours. This is just an example. Other things I could use are a front rando bag, a front rack, bottle cages, 27" tanwalls, goatskin or elk leather suitable for making bar covering, derelict Brooks (or similar) saddles, an orbital sander, an engraving tool, a few 2 gallon plastic planters, a mask with filters (yes I am flexible). Someone, please, make me an offer. I'm eager to see this (and one of my larger boxes) gone to a better place.



__________________
In search of what to search for.

Last edited by USAZorro; 02-06-24 at 03:51 PM.
USAZorro is offline  
Likes For USAZorro:
Old 02-07-24, 12:14 PM
  #6408  
Senior Member
 
delicious's Avatar
 
Join Date: Jun 2006
Location: berkeley
Posts: 1,807
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 88 Post(s)
Liked 60 Times in 34 Posts
WTB: C-record seatpost 27.2

Have Super and Nuovo posts that I could include as a partial trade

Thanks!
delicious is offline  
Old 02-08-24, 06:49 PM
  #6409  
Tinker-er
 
Join Date: Oct 2007
Location: Mid-Atlantic
Posts: 375

Bikes: 1956 Rudge Sports; 1983 Univega Alpina Uno; 1981 Miyata 610; 1973 Raleigh Twenty; 1994 Breezer Lightning XTR; V4 Yuba Mundo aka "The Schlepper"; 1987 Raleigh "The Edge" Mountain Trials; 1951 Rudge Aero Clubman; 1978 Raleigh Competition GS

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 148 Post(s)
Liked 224 Times in 152 Posts
ISO: Raleigh or Raleigh subsidiary lugged crown 27" wheel fork. Need at least 190mm steer tube. Prefer 27.0mm crown race. If I can't find a Raleigh or Carlton fork anything decent will do, probably. This is for a freebie new acquisition Super Course Mk II which will get all the components from my 1951 Rudge Aero Clubman which is just a bit too small.
Please PM me if you have a fork that may work. It's difficult to keep up with this thread, it's so active!
UPDATE: Found a fork!
Thanks all!
Phil

Last edited by PhilFo; 02-08-24 at 09:31 PM.
PhilFo is offline  
Old 02-08-24, 07:06 PM
  #6410  
Phyllo-buster
 
clubman's Avatar
 
Join Date: Jan 2010
Location: Nova Scotia
Posts: 8,825

Bikes: roadsters, club bikes, fixed and classic

Mentioned: 133 Post(s)
Tagged: 0 Thread(s)
Quoted: 2284 Post(s)
Liked 2,017 Times in 1,240 Posts
Originally Posted by PhilFo
ISO: Raleigh or Raleigh subsidiary lugged crown 27" wheel fork. Need at least 190mm steer tube. Prefer 27.0mm crown race. If I can't find a Raleigh or Carlton fork anything decent will do, probably. This is for a freebie new acquisition Super Course Mk II which will get all the components from my 1951 Rudge Aero Clubman which is just a bit too small.
Please PM me if you have a fork that may work. It's difficult to keep up with this thread, it's so active!
Thanks all!
Phil
Are you sure it takes a 27"? My 76 MKII came with Weinmann 700's
clubman is offline  
Old 02-09-24, 01:42 PM
  #6411  
Señor Member
 
USAZorro's Avatar
 
Join Date: Oct 2004
Location: Hardy, VA
Posts: 17,924

Bikes: Mostly English - predominantly Raleighs

Mentioned: 70 Post(s)
Tagged: 0 Thread(s)
Quoted: 1485 Post(s)
Liked 1,053 Times in 626 Posts
Originally Posted by clubman
Are you sure it takes a 27"? My 76 MKII came with Weinmann 700's
My 1978 (the different style with no chrome on the frame and with Sun Tour mechs) also had 700c with Weinmann concaves.
__________________
In search of what to search for.
USAZorro is offline  
Old 02-10-24, 07:30 AM
  #6412  
Senior Member
 
Murray Missile's Avatar
 
Join Date: Jun 2013
Location: 700 Ft. above sea level.
Posts: 3,153

Bikes: More than there were awhile ago.

Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 592 Post(s)
Liked 1,131 Times in 546 Posts
FOUND ONE! ISO Simplex SLJ5000 RD part.

Found one, thanks all.

I just acquired a very clean and tight 1st Design SLJ5000 RD but the tab on the tension plate where it sits against the hanger has been broken off so I'm in need of a replacement. I'd prefer just that piece but I'd take a complete derailleur if you have one that's worn out, rusty, mangled and nly good for parts as long as that piece is in good condition. I don't want to part out a decent functional derailleur just to make this one whole.... yet. TIA.

__________________
".....distasteful and easily triggered."

Last edited by Murray Missile; 02-12-24 at 05:18 AM. Reason: Part located.
Murray Missile is offline  
Old 02-10-24, 07:44 AM
  #6413  
Senior Member
 
Join Date: Jun 2021
Posts: 1,802

Bikes: '38 Schwinn New World, ’69 Peugeot PX-10, '72 Peugeot PX-10, ‘7? Valgan, '78 Raleigh Comp GS, ’79 Holdsworth Pro, ’80 Peugeot TH-8 tandem, '87 Trek 400T, ‘7? Raleigh Sports, ‘7? Raleigh Superbe, ‘6? Hercules

Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 749 Post(s)
Liked 1,501 Times in 733 Posts
Originally Posted by Murray Missile
I just acquired a very clean and tight 1st Design SLJ5000 RD but the tab on the tension plate where it sits against the hanger has been broken off so I'm in need of a replacement. I'd prefer just that piece but I'd take a complete derailleur if you have one that's worn out, rusty, mangled and nly good for parts as long as that piece is in good condition. I don't want to part out a decent functional derailleur just to make this one whole.... yet. TIA.

I believe that, with the exception of the holes for the spring not being present, the matching part from a Criterium/Delrin RD is the same- you may have an easier time finding one of those to cannibalize and carefully drill the holes in it.
ehcoplex is offline  
Old 02-10-24, 08:19 AM
  #6414  
Full Member
 
Portlandjim's Avatar
 
Join Date: May 2023
Location: Big Sur California
Posts: 208

Bikes: 1946 Holdsworth Cyclone, 1969 Cinelli SC, 1972 Raleigh Pro, 1973 Merz road bike, 1974 Alex Singer Sportif, 1974 Merz track bike, 1975 Teledyne Titan, 1976 Ritchey road bike, 1977 DiNucci built Merz track bike, 1977 (?) Exxon Graftek, many more!

Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 135 Post(s)
Liked 1,384 Times in 167 Posts
Simplex SLJ5000 RD part 3557

Originally Posted by Murray Missile
I just acquired a very clean and tight 1st Design SLJ5000 RD but the tab on the tension plate where it sits against the hanger has been broken off so I'm in need of a replacement. I'd prefer just that piece but I'd take a complete derailleur if you have one that's worn out, rusty, mangled and nly good for parts as long as that piece is in good condition. I don't want to part out a decent functional derailleur just to make this one whole.... yet. TIA.

I don't have the plate you're looking for, but I do have one NOS black aluminum nut (?) thing that fits into the plate. The flat is prone to rounding off, it's not ovious how to remove the rear derailleur and if you think it's like a Campanlo SR you will ruin this part. These are very hard to find! $25 shipped in the 48 states. Jim Merz
Portlandjim is offline  
Likes For Portlandjim:
Old 02-10-24, 11:48 AM
  #6415  
Senior Member
 
Murray Missile's Avatar
 
Join Date: Jun 2013
Location: 700 Ft. above sea level.
Posts: 3,153

Bikes: More than there were awhile ago.

Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 592 Post(s)
Liked 1,131 Times in 546 Posts
Originally Posted by Portlandjim
I don't have the plate you're looking for, but I do have one NOS black aluminum nut (?) thing that fits into the plate. The flat is prone to rounding off, it's not ovious how to remove the rear derailleur and if you think it's like a Campanlo SR you will ruin this part. These are very hard to find! $25 shipped in the 48 states. Jim Merz
Thanks but fortunately mine has not been so violated, evidently whoever removed it knew this valuable bit of intel as well.
__________________
".....distasteful and easily triggered."
Murray Missile is offline  
Old 02-11-24, 11:02 AM
  #6416  
Tinker-er
 
Join Date: Oct 2007
Location: Mid-Atlantic
Posts: 375

Bikes: 1956 Rudge Sports; 1983 Univega Alpina Uno; 1981 Miyata 610; 1973 Raleigh Twenty; 1994 Breezer Lightning XTR; V4 Yuba Mundo aka "The Schlepper"; 1987 Raleigh "The Edge" Mountain Trials; 1951 Rudge Aero Clubman; 1978 Raleigh Competition GS

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 148 Post(s)
Liked 224 Times in 152 Posts
ISO: Suntour Superbe Pro drive side crank. 165mm arm, 130BCD strongly preferred. I'm willing to buy a whole crankset for the drive side only. Also willing to use a Sugino version of the Superbe Pro: AP130. Suntour Sprint 165mm with 130BCD would work also. The crankarm length is the important part.
Many thanks all!
Phil

Last edited by PhilFo; 02-21-24 at 04:59 PM.
PhilFo is offline  
Old 02-12-24, 03:52 PM
  #6417  
Señor Member
 
USAZorro's Avatar
 
Join Date: Oct 2004
Location: Hardy, VA
Posts: 17,924

Bikes: Mostly English - predominantly Raleighs

Mentioned: 70 Post(s)
Tagged: 0 Thread(s)
Quoted: 1485 Post(s)
Liked 1,053 Times in 626 Posts
I have a relatively pristine chromed steel rear rim that's laced to a Sturmey Archer AW hub shell. What I'm lacking is the business part of the hub. I have a more modern RSF hub that's not laced to anything, but even if it would fit (which I am skeptical of), I do not thing that's the ideal thing to transplant into this "shell". I don't even have a frame in mind at this point, but as I have a matching front rim, and a suitable hub for that, I am thinking, "why not see if I can locate something that would be usable?" I am far from an expert on this technology, but I am thinking that, while the shell says AW, an AM, FM, FW or possibly other internals would work.

This is far from an urgent request, but I am thinking that at some point in the future, I may want to spiff up a three speed with "appropriate" parts, and the wheel set could be a significant part of the endeavor. If you have such an item gathering dust, and would be inclined to make a trade, I'd be quite open to it and grateful for it.

edit: If you happen to have a complete AW, AM, FW or FM and would be interested in a trade, I'm certainly open to that as well.

TIA
__________________
In search of what to search for.

Last edited by USAZorro; 02-17-24 at 02:39 PM. Reason: additional information
USAZorro is offline  
Old 02-14-24, 07:18 PM
  #6418  
Senior Member
 
Murray Missile's Avatar
 
Join Date: Jun 2013
Location: 700 Ft. above sea level.
Posts: 3,153

Bikes: More than there were awhile ago.

Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 592 Post(s)
Liked 1,131 Times in 546 Posts
RSX hubs no longer needed. Thanks.

Took the path of least reistance and went a different route. Thanks.

Last edited by Murray Missile; 02-20-24 at 05:28 AM. Reason: Went different route.
Murray Missile is offline  
Old 02-15-24, 02:41 PM
  #6419  
Full Member
 
VintageSteelEU's Avatar
 
Join Date: May 2021
Location: London
Posts: 492

Bikes: Motobecane C41, Matsu$hita Nashonaru

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 194 Post(s)
Liked 343 Times in 209 Posts
Originally Posted by Murray Missile
I need a set of Shimano RSX 36 hole hubs, all I can find in the Western Hemishpere are 32h. A 7 speed freehub is a plus, believe it or not, but an 8 will do just as well. They don't have to be show quality just presentable with a little spit shine. For the rear I can get by with just the shell if need be, I have a 32h I can cannibalize but the front needs to be complete.
I have a front Shimano 36H from the era, but not RSX. Exage 500EX, if I remember correctly. Decent hub.
Also, there are almost no differences between Shimano hubs of the era in terms of shape. Finish might be different (this one is polished anyway), locknuts might be differently shaped and I guess they might be using slightly different materials, but my suspicion is they were churning them all out from a single production line and then just changing finish and some hardware and putting them in different boxes. Put in decent grade bearing balls and Bob's your uncle
VintageSteelEU is offline  
Old 02-15-24, 06:59 PM
  #6420  
Senior Member
 
Murray Missile's Avatar
 
Join Date: Jun 2013
Location: 700 Ft. above sea level.
Posts: 3,153

Bikes: More than there were awhile ago.

Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 592 Post(s)
Liked 1,131 Times in 546 Posts
Originally Posted by VintageSteelEU
I have a front Shimano 36H from the era, but not RSX. Exage 500EX, if I remember correctly. Decent hub.
Also, there are almost no differences between Shimano hubs of the era in terms of shape. Finish might be different (this one is polished anyway), locknuts might be differently shaped and I guess they might be using slightly different materials, but my suspicion is they were churning them all out from a single production line and then just changing finish and some hardware and putting them in different boxes. Put in decent grade bearing balls and Bob's your uncle
Yeah, you're pretty much on point, wihtout the stickers it's hard to tell the difference on a lot of them BUT "if" I can find a set of RSX with original labels that would be great. If I can't then I'll go for the next best thing. I'll keep yours in mind if I don't come up with a set soon. Thanks.
__________________
".....distasteful and easily triggered."
Murray Missile is offline  
Old 02-16-24, 02:58 AM
  #6421  
Edumacator
 
Join Date: Jan 2018
Location: Goose Creek, SC
Posts: 7,288

Bikes: '87 Crestdale, '87 Basso Gap, '92 Rossin Performance EL-OS, 1990 VanTuyl, 1980s Losa, 1985 Trek 670, 1982 AD SLE, 1987 PX10, etc...

Mentioned: 55 Post(s)
Tagged: 0 Thread(s)
Quoted: 2352 Post(s)
Liked 2,851 Times in 1,824 Posts
Originally Posted by Murray Missile
Yeah, you're pretty much on point, wihtout the stickers it's hard to tell the difference on a lot of them BUT "if" I can find a set of RSX with original labels that would be great. If I can't then I'll go for the next best thing. I'll keep yours in mind if I don't come up with a set soon. Thanks.
Unfortunately my two sets are attached to two decent sets of wheels...
__________________
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super












jdawginsc is offline  
Old 02-16-24, 01:29 PM
  #6422  
Senior Member
 
Join Date: Jul 2022
Location: Pac NW
Posts: 1,843

Bikes: several Eddy Merz (ride like Eddy, braze like Jim!)

Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 999 Post(s)
Liked 1,621 Times in 603 Posts
WTT or buy, COLNAGO FORK

My chrome colnago fork is .5cm to short for the stack. I've already attempted using a PISTA set (33 vs 37) and its still too short.

I don't care if its chrome or painted.

Thanks
__________________
"Leave the gun. Take the Colnagos."
Robvolz is offline  
Old 02-16-24, 04:07 PM
  #6423  
Senior Member
 
Murray Missile's Avatar
 
Join Date: Jun 2013
Location: 700 Ft. above sea level.
Posts: 3,153

Bikes: More than there were awhile ago.

Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 592 Post(s)
Liked 1,131 Times in 546 Posts
Originally Posted by jdawginsc
Unfortunately my two sets are attached to two decent sets of wheels...
Actually if I found a set of wheels with RSX and the "right" set of rims I'd consider that too. I have a Guerciotti I need to build a set of wheels for and the Campy Super Record hubs I have for it are also 36 hole. In fact I originally bought the rims for it but they clashed horribly with the blue on it, I decided I rather have more traditional polished rims for it anyway.
__________________
".....distasteful and easily triggered."
Murray Missile is offline  
Old 02-16-24, 06:18 PM
  #6424  
Making up the numbers
 
seagrade's Avatar
 
Join Date: Jun 2022
Posts: 252
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 92 Post(s)
Liked 414 Times in 133 Posts
Originally Posted by Robvolz
My chrome colnago fork is .5cm to short for the stack. I've already attempted using a PISTA set (33 vs 37) and its still too short.

I don't care if its chrome or painted.

Thanks
If you can find one Tange Levin headsets are 31mm stack and wouldn’t look completely wrong in a C&V Colnago according to my opinion.

That and milling 1mm off top and bottom of head tube, if that much is still available, might get you there with the existing fork.

Then again, just because something can be done doesn’t mean it should be done. The effect of lowering the front end by 4-5mm should be considered, but worse indignities have been inflicted upon classic frames to keep them in the fray.
__________________
Nothing quite says wall hanger like drillium toe straps
seagrade is offline  
Old 02-16-24, 09:33 PM
  #6425  
Edumacator
 
Join Date: Jan 2018
Location: Goose Creek, SC
Posts: 7,288

Bikes: '87 Crestdale, '87 Basso Gap, '92 Rossin Performance EL-OS, 1990 VanTuyl, 1980s Losa, 1985 Trek 670, 1982 AD SLE, 1987 PX10, etc...

Mentioned: 55 Post(s)
Tagged: 0 Thread(s)
Quoted: 2352 Post(s)
Liked 2,851 Times in 1,824 Posts
Originally Posted by Murray Missile
Actually if I found a set of wheels with RSX and the "right" set of rims I'd consider that too. I have a Guerciotti I need to build a set of wheels for and the Campy Super Record hubs I have for it are also 36 hole. In fact I originally bought the rims for it but they clashed horribly with the blue on it, I decided I rather have more traditional polished rims for it anyway.
Let me know if you want me to dig through the portable, temporary storage unit.
__________________
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 1982 AD SLE, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super












jdawginsc is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.