Saddle cover peeling?
#1
Senior Member
Thread Starter
Saddle cover peeling?
I put the original saddle back on my 1983 Miyata 710. I'd never used it before today, but I think I've got it set up in a way that I like. BUT - and this is part of why I'd replaced it with a different saddle in the first place when I got the bike a couple years ago - the saddle's cover fabric is held on just by adhesive, and the adhesive is failing in back:
Besides the fact that it's falling off, the fabric seems to be in good condition, and I'd like to re-attach it. How should I go about this? Hit it with something like a headliner adhesive and clamp it in place while it sets?
Besides the fact that it's falling off, the fabric seems to be in good condition, and I'd like to re-attach it. How should I go about this? Hit it with something like a headliner adhesive and clamp it in place while it sets?
#2
Senior Member
Join Date: Jun 2006
Posts: 20,305
Mentioned: 130 Post(s)
Tagged: 0 Thread(s)
Quoted: 3464 Post(s)
Liked 2,829 Times
in
1,995 Posts
Sand the nylon base. clean off the sanding debris.
Take a small glass jar with a screw on lid and politely implore a local cobbler for some adhesive.
Pay him.
get a disposable acid brush or two and prime the two contact surfaces, apply a coat after the first has "flashed" off.
pull into position, a heat gun / hair dryer may help.
clamping without marring is tough.
this is one of the few times I cannot tell what the cover material is.
Take a small glass jar with a screw on lid and politely implore a local cobbler for some adhesive.
Pay him.
get a disposable acid brush or two and prime the two contact surfaces, apply a coat after the first has "flashed" off.
pull into position, a heat gun / hair dryer may help.
clamping without marring is tough.
this is one of the few times I cannot tell what the cover material is.
#3
Senior Member
Or simply buy some Barge contact cement and do as above. No cobbler harassment necessary.
#4
Senior Member
Join Date: Nov 2015
Posts: 4,485
Mentioned: 102 Post(s)
Tagged: 0 Thread(s)
Quoted: 1639 Post(s)
Likes: 0
Liked 829 Times
in
538 Posts
+1 on contact cement. Don't bother with 3M spray-on stuff as it will not do a permanent repair like contact cement will....
__________________
72 Line Seeker
83 Davidson Signature
84 Peugeot PSV
84 Peugeot PY10FC
84 Gitane Tour de France.
85 Vitus Plus Carbone 7
86 ALAN Record Carbonio
86 Medici Aerodynamic (Project)
88 Pinarello Montello
89 Bottecchia Professional Chorus SL
95 Trek 5500 OCLV (Project)
72 Line Seeker
83 Davidson Signature
84 Peugeot PSV
84 Peugeot PY10FC
84 Gitane Tour de France.
85 Vitus Plus Carbone 7
86 ALAN Record Carbonio
86 Medici Aerodynamic (Project)
88 Pinarello Montello
89 Bottecchia Professional Chorus SL
95 Trek 5500 OCLV (Project)
#5
Senior Member
Thread Starter
#6
Extraordinary Magnitude
Join Date: Aug 2009
Location: Waukesha WI
Posts: 13,646
Bikes: 1978 Trek TX700; 1978/79 Trek 736; 1984 Specialized Stumpjumper Sport; 1984 Schwinn Voyageur SP; 1985 Trek 620; 1985 Trek 720; 1986 Trek 400 Elance; 1987 Schwinn High Sierra; 1990 Miyata 1000LT
Mentioned: 84 Post(s)
Tagged: 0 Thread(s)
Quoted: 2608 Post(s)
Liked 1,699 Times
in
935 Posts
__________________
*Recipient of the 2006 Time Magazine "Person Of The Year" Award*
Commence to jigglin’ huh?!?!
"But hey, always love to hear from opinionated amateurs." -says some guy to Mr. Marshall.
Commence to jigglin’ huh?!?!
"But hey, always love to hear from opinionated amateurs." -says some guy to Mr. Marshall.
#7
Senior Member
Join Date: Nov 2005
Location: NW Ohio
Posts: 3,419
Bikes: 1984 Miyata 310, 1986 Schwinn Sierra, 2011 Jamis Quest, 1980 Peugeot TH8 Tandem, 1992 Performance Parabola, 1987 Ross Mt. Hood, 1988 Schwinn LeTour, 1988 Trek 400T, 1981 Fuji S12-S LTD, 197? FW Evans
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 531 Post(s)
Liked 1,004 Times
in
514 Posts
The same thing happened to my Miyata 310 saddle. I used contact cement to fix it. Make sure you cover both surfaces with the cement and let dry for several minutes before pressing them together. If you press them together while still wet, they don't stick as well.
#8
...addicted...
I tried headliner adhesive and it's too messy.
#9
Banned
Barge vinyl stick, was used to completely replace the cover on a very old saddle with a nylon base,
Seems recent 'healthier' volatile solvent contact cements,
have a side effect of not working as well..
Seems recent 'healthier' volatile solvent contact cements,
have a side effect of not working as well..
#11
Senior Member
Join Date: Mar 2014
Location: City of Angels
Posts: 4,870
Bikes: A few too many
Mentioned: 42 Post(s)
Tagged: 1 Thread(s)
Quoted: 1364 Post(s)
Liked 2,180 Times
in
1,183 Posts
"Toxic" contact cement for me and has been my go-to for years, not low the VOC that is less reliable....I am lucky enough that I have a well-sealed quart (stored upside down) that should last my lifetime.
Best, Ben
Best, Ben
__________________
"EVERY PERSON IS GUILTY OF ALL THE GOOD THEY DID NOT DO"
Voltaire
Voice recognition may sometimes create odd spelling and grammatical errors
"EVERY PERSON IS GUILTY OF ALL THE GOOD THEY DID NOT DO"
Voltaire
Voice recognition may sometimes create odd spelling and grammatical errors
#12
Senior Member
Join Date: Nov 2015
Posts: 4,485
Mentioned: 102 Post(s)
Tagged: 0 Thread(s)
Quoted: 1639 Post(s)
Likes: 0
Liked 829 Times
in
538 Posts
Expose it to heat long enough like when you might leave your bike out in the summer sun, and that spray on 3M 77 will give up its grip.
I used a lot of the stuff for my college projects and know about its limitations....
Most good saddle manufacturers use contact cement to glue on their covers. No reason why not to use the same....
I used a lot of the stuff for my college projects and know about its limitations....
Most good saddle manufacturers use contact cement to glue on their covers. No reason why not to use the same....