Help (advice) needed with French freewheel
#1
Senior Member
Thread Starter
Help (advice) needed with French freewheel
I am trying to get an 8 speed Sachs Maillard freewheel off. I am thinking the smallest cog(s) act as a lock ring? I remember in the bike shop, we always had 2 chain whips, but I have gotten by with one for the last 30 some years. Also the cogs have an interesting tooth profile. (This is mated to 1990 era Huret-Sachs Rival 8 speed indexed shifters and derailleurs). See pics.
Cool vee shaped tooth profile , on the outer edge
Not what I am used to freewheel wise!
Cool vee shaped tooth profile , on the outer edge
Not what I am used to freewheel wise!
#2
Senior Member
Join Date: Feb 2020
Posts: 2,817
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1106 Post(s)
Likes: 0
Liked 1,326 Times
in
782 Posts
If it's a freewheel you need a tool that fits over the axle and engages what appear to be splines within.
There's this new fad called cassettes and they are different, I don't know, maybe they come off with whips.
There's this new fad called cassettes and they are different, I don't know, maybe they come off with whips.
#3
Senior Member
Join Date: Jan 2015
Location: Los Angeles
Posts: 4,703
Bikes: 82 Medici, 2011 Richard Sachs, 2011 Milwaukee Road
Mentioned: 55 Post(s)
Tagged: 0 Thread(s)
Quoted: 1947 Post(s)
Liked 2,009 Times
in
1,108 Posts
I’m a fan of the 6 and 7 speed freewheels and its fun to pair them with a Sachs/SRAM chain. Maybe that tooth top treatment helps them run quieter? That could be a UG cassette.
__________________
I don't do: disks, tubeless, e-shifting, or bead head nymphs.
I don't do: disks, tubeless, e-shifting, or bead head nymphs.
Likes For Classtime:
#4
Bianchi Goddess
Join Date: Apr 2009
Location: Shady Pines Retirement Fort Wayne, In
Posts: 27,858
Bikes: Too many to list here check my signature.
Mentioned: 192 Post(s)
Tagged: 2 Thread(s)
Quoted: 2930 Post(s)
Liked 2,923 Times
in
1,491 Posts
All I know about them is they usually don’t put up much of a fight when you want to remove them.
__________________
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
#5
Insane Bicycle Mechanic
Join Date: Mar 2008
Location: other Vancouver
Posts: 9,835
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 802 Post(s)
Liked 703 Times
in
376 Posts
It's definitely a freewheel- you can see the removal splines behind the outer locknut. If that's a later-model freewheel, it takes the same tool as Shimano freewheels.
If you can't get enough engagement on the freewheel splines, remove the outer locknut and spacer.
If you can't get enough engagement on the freewheel splines, remove the outer locknut and spacer.
__________________
Jeff Wills
Comcast nuked my web page. It will return soon..
Jeff Wills
Comcast nuked my web page. It will return soon..
Likes For Jeff Wills:
#6
Senior Member
Join Date: Oct 2010
Posts: 8,515
Mentioned: 69 Post(s)
Tagged: 0 Thread(s)
Quoted: 3241 Post(s)
Liked 2,512 Times
in
1,510 Posts
I see notches in there. Here's the Velobase page that might help.
https://velobase.com/ListComponents....3-3cad77fcf335
https://velobase.com/ListComponents....3-3cad77fcf335
Likes For seypat:
#7
Senior Member
Thread Starter
I see notches in there. Here's the Velobase page that might help.
https://velobase.com/ListComponents....3-3cad77fcf335
https://velobase.com/ListComponents....3-3cad77fcf335
you can see the funky teeth very clearly there.
Likes For mgopack42:
#8
Senior Member
Join Date: Nov 2015
Posts: 4,485
Mentioned: 102 Post(s)
Tagged: 0 Thread(s)
Quoted: 1639 Post(s)
Likes: 0
Liked 828 Times
in
537 Posts
The worst ones to take out are the Reginas. I had a few that were so tight on the hubs that I felt like I busted my ribs when I took them off. A couple of my chain whips actually broke on me when removing Regina FWs.
__________________
72 Line Seeker
83 Davidson Signature
84 Peugeot PSV
84 Peugeot PY10FC
84 Gitane Tour de France.
85 Vitus Plus Carbone 7
86 ALAN Record Carbonio
86 Medici Aerodynamic (Project)
88 Pinarello Montello
89 Bottecchia Professional Chorus SL
95 Trek 5500 OCLV (Project)
72 Line Seeker
83 Davidson Signature
84 Peugeot PSV
84 Peugeot PY10FC
84 Gitane Tour de France.
85 Vitus Plus Carbone 7
86 ALAN Record Carbonio
86 Medici Aerodynamic (Project)
88 Pinarello Montello
89 Bottecchia Professional Chorus SL
95 Trek 5500 OCLV (Project)
#9
Senior Member
Join Date: Feb 2020
Posts: 2,817
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1106 Post(s)
Likes: 0
Liked 1,326 Times
in
782 Posts
Yes, the Maillard/Sachs FWs definely usually comes off the hubs quite easily.
The worst ones to take out are the Reginas. I had a few that were so tight on the hubs that I felt like I busted my ribs when I took them off. A couple of my chain whips actually broke on me when removing Regina FWs.
The worst ones to take out are the Reginas. I had a few that were so tight on the hubs that I felt like I busted my ribs when I took them off. A couple of my chain whips actually broke on me when removing Regina FWs.
#10
Standard Member
Join Date: Apr 2009
Location: Brunswick, Maine
Posts: 4,268
Bikes: 1948 P. Barnard & Son, 1962 Rudge Sports, 1963 Freddie Grubb Routier, 1980 Manufrance Hirondelle, 1983 F. Moser Sprint, 1989 Raleigh Technium Pre, 2001 Raleigh M80
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 1296 Post(s)
Liked 940 Times
in
490 Posts
You are right. This is the one that it is...Sachs-Maillard Aris
you can see the funky teeth very clearly there.
you can see the funky teeth very clearly there.
#11
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,784
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3587 Post(s)
Liked 3,398 Times
in
1,932 Posts
#12
Standard Member
Join Date: Apr 2009
Location: Brunswick, Maine
Posts: 4,268
Bikes: 1948 P. Barnard & Son, 1962 Rudge Sports, 1963 Freddie Grubb Routier, 1980 Manufrance Hirondelle, 1983 F. Moser Sprint, 1989 Raleigh Technium Pre, 2001 Raleigh M80
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 1296 Post(s)
Liked 940 Times
in
490 Posts
You are right about the A.R.I.S. needing the FR-1. It had been so long since I have removed my 6-speed A.R.I.S, that I thought it required the standard Maillard tool, FR-4.
Last edited by 1989Pre; 11-15-22 at 03:45 AM.
#13
Bianchi Goddess
Join Date: Apr 2009
Location: Shady Pines Retirement Fort Wayne, In
Posts: 27,858
Bikes: Too many to list here check my signature.
Mentioned: 192 Post(s)
Tagged: 2 Thread(s)
Quoted: 2930 Post(s)
Liked 2,923 Times
in
1,491 Posts
Yes, the Maillard/Sachs FWs definely usually comes off the hubs quite easily.
The worst ones to take out are the Reginas. I had a few that were so tight on the hubs that I felt like I busted my ribs when I took them off. A couple of my chain whips actually broke on me when removing Regina FWs.
The worst ones to take out are the Reginas. I had a few that were so tight on the hubs that I felt like I busted my ribs when I took them off. A couple of my chain whips actually broke on me when removing Regina FWs.
__________________
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
#14
Freewheel Medic
Join Date: Oct 2005
Location: An Island on the Coast of GA!
Posts: 12,882
Bikes: Snazzy* Schwinns, Classy Cannondales & a Super Pro Aero Lotus (* Ed.)
Mentioned: 140 Post(s)
Tagged: 0 Thread(s)
Quoted: 1452 Post(s)
Liked 2,194 Times
in
962 Posts
I've used (and serviced many) Sachs Aris freewheels, and a modern Shimano tool has always worked for me.
While the Sachs Aris is one of my favorite freewheels to run on a wheel spaced for 126mm rear dropouts, the eight-speed models are intended for 130mm spacing, which does run the risk the hub axle bending since the the bearing cone on the drive side is far inside from the locknut.
The other concern with this model has to do with the type of grease and the method used by Sachs to apply the grease. The bearings are held in red plastic cages which double as seals to keep contaminates from penetrating the interior.
Since no grease is needed to keep the bearings in place during assembly, an injector hole was added to the outer body. Sachs then flooded the interior with grease through this hole. Thus, the bearings and the pawls were embedded in grease. Fast forward three decades and in most cases the original Sachs grease has spoiled into a sticky peanut butter mess.
The Drip and Dribble method of freewheel service will never work on an Aris. It needs to be disassembled, cleaned and new grease added to the races only. I use a few drops of quality machine oil on the pawl pivots.
While the Sachs Aris is one of my favorite freewheels to run on a wheel spaced for 126mm rear dropouts, the eight-speed models are intended for 130mm spacing, which does run the risk the hub axle bending since the the bearing cone on the drive side is far inside from the locknut.
The other concern with this model has to do with the type of grease and the method used by Sachs to apply the grease. The bearings are held in red plastic cages which double as seals to keep contaminates from penetrating the interior.
Since no grease is needed to keep the bearings in place during assembly, an injector hole was added to the outer body. Sachs then flooded the interior with grease through this hole. Thus, the bearings and the pawls were embedded in grease. Fast forward three decades and in most cases the original Sachs grease has spoiled into a sticky peanut butter mess.
The Drip and Dribble method of freewheel service will never work on an Aris. It needs to be disassembled, cleaned and new grease added to the races only. I use a few drops of quality machine oil on the pawl pivots.
__________________
Bob
Enjoying the GA coast all year long!
Thanks for visiting my website: www.freewheelspa.com
Bob
Enjoying the GA coast all year long!
Thanks for visiting my website: www.freewheelspa.com
#15
Senior Member
Thread Starter
I've used (and serviced many) Sachs Aris freewheels, and a modern Shimano tool has always worked for me.
While the Sachs Aris is one of my favorite freewheels to run on a wheel spaced for 126mm rear dropouts, the eight-speed models are intended for 130mm spacing, which does run the risk the hub axle bending since the the bearing cone on the drive side is far inside from the locknut.
The other concern with this model has to do with the type of grease and the method used by Sachs to apply the grease. The bearings are held in red plastic cages which double as seals to keep contaminates from penetrating the interior.
Since no grease is needed to keep the bearings in place during assembly, an injector hole was added to the outer body. Sachs then flooded the interior with grease through this hole. Thus, the bearings and the pawls were embedded in grease. Fast forward three decades and in most cases the original Sachs grease has spoiled into a sticky peanut butter mess.
The Drip and Dribble method of freewheel service will never work on an Aris. It needs to be disassembled, cleaned and new grease added to the races only. I use a few drops of quality machine oil on the pawl pivots.
While the Sachs Aris is one of my favorite freewheels to run on a wheel spaced for 126mm rear dropouts, the eight-speed models are intended for 130mm spacing, which does run the risk the hub axle bending since the the bearing cone on the drive side is far inside from the locknut.
The other concern with this model has to do with the type of grease and the method used by Sachs to apply the grease. The bearings are held in red plastic cages which double as seals to keep contaminates from penetrating the interior.
Since no grease is needed to keep the bearings in place during assembly, an injector hole was added to the outer body. Sachs then flooded the interior with grease through this hole. Thus, the bearings and the pawls were embedded in grease. Fast forward three decades and in most cases the original Sachs grease has spoiled into a sticky peanut butter mess.
The Drip and Dribble method of freewheel service will never work on an Aris. It needs to be disassembled, cleaned and new grease added to the races only. I use a few drops of quality machine oil on the pawl pivots.
Likes For mgopack42:
#16
Senior Member
Join Date: Apr 2012
Location: Middle Earth (aka IA)
Posts: 20,435
Bikes: A bunch of old bikes and a few new ones
Mentioned: 178 Post(s)
Tagged: 0 Thread(s)
Quoted: 5888 Post(s)
Liked 3,471 Times
in
2,079 Posts
I've used (and serviced many) Sachs Aris freewheels, and a modern Shimano tool has always worked for me.
While the Sachs Aris is one of my favorite freewheels to run on a wheel spaced for 126mm rear dropouts, the eight-speed models are intended for 130mm spacing, which does run the risk the hub axle bending since the the bearing cone on the drive side is far inside from the locknut.
The other concern with this model has to do with the type of grease and the method used by Sachs to apply the grease. The bearings are held in red plastic cages which double as seals to keep contaminates from penetrating the interior.
Since no grease is needed to keep the bearings in place during assembly, an injector hole was added to the outer body. Sachs then flooded the interior with grease through this hole. Thus, the bearings and the pawls were embedded in grease. Fast forward three decades and in most cases the original Sachs grease has spoiled into a sticky peanut butter mess.
snip . . .
The Drip and Dribble method of freewheel service will never work on an Aris. It needs to be disassembled, cleaned and new grease added to the races only. I use a few drops of quality machine oil on the pawl pivots.
While the Sachs Aris is one of my favorite freewheels to run on a wheel spaced for 126mm rear dropouts, the eight-speed models are intended for 130mm spacing, which does run the risk the hub axle bending since the the bearing cone on the drive side is far inside from the locknut.
The other concern with this model has to do with the type of grease and the method used by Sachs to apply the grease. The bearings are held in red plastic cages which double as seals to keep contaminates from penetrating the interior.
Since no grease is needed to keep the bearings in place during assembly, an injector hole was added to the outer body. Sachs then flooded the interior with grease through this hole. Thus, the bearings and the pawls were embedded in grease. Fast forward three decades and in most cases the original Sachs grease has spoiled into a sticky peanut butter mess.
snip . . .
The Drip and Dribble method of freewheel service will never work on an Aris. It needs to be disassembled, cleaned and new grease added to the races only. I use a few drops of quality machine oil on the pawl pivots.
Likes For bikemig: