Bike Forums

Bike Forums (https://www.bikeforums.net/forum.php)
-   Classic & Vintage (https://www.bikeforums.net/classic-vintage/)
-   -   removing decals ? (https://www.bikeforums.net/classic-vintage/267234-removing-decals.html)

steve502 02-07-07 10:57 AM

removing decals ?
 
Any one have experience removing decals . I was wondering what the best solvent may be for that , evidently my concern is using something that will not have adverse affects on paint , BTW the labels have no clear coat on them

thanks
Steve

Little Darwin 02-07-07 11:29 AM

Are you talking about decals, or stickers?

For decals, I have had good luck removing decals from an old bike by carefully using the back side of a butter knife to rub/scrape it off.

For stickers, I recall reading about good results with all of the various anti-goo products or WD-40 for removing the residue.

TheSlav 02-07-07 11:33 AM

Hair dryer works pretty good to loosen up old adhesive a bit

unworthy1 02-07-07 11:40 AM

stickers with pressure-sensitive adhesive respond well to heat, I use a hair dryer set high and gently pull the hot vinyl as I move the heat along. It often comes off completely clean with no residue. Water-slide decals (like a 531 tube decals) that aren't coated with some kind of varnish or clear will usually scrape off with a fingernail...or just by staring hard at them ;) . For residue and sticker gunk I used to use WD40 and solvents like Goo Gone but now I find naptha (AKA lighter fluid for Zippos and Ronsons) works even better and leaves no oily film to wash off. But make sure it doesn't harm the paint, so far not a problem on any frame I used it on.

M-theory 02-07-07 05:15 PM

Ditto Unworthy and TheSlav.... Hot hair dryer works wonders. This is accomplished by holding the hairdryer (on hottest, high setting) directly on the decal, about an inch away from the surface, for about 15 seconds. It then peels off easily.

This also worked to take off my "TOYOTA" decals on the gate of my truck, and just about every decal I've ever tried it on.

braingel 02-07-07 05:22 PM

i tried the hair dryer last week for the frst time...it was like magic.

Jet Travis 02-07-07 06:42 PM


Originally Posted by braingel
i tried the hair dryer last week for the frst time...it was like magic.

+1

I had a Lemond with, like, nine "Lemond" decals. I decided to take one or two off with my wife's hair dryer. It worked so well, I ended up stripping the entire bike. I like my frame in its new stealthy form.

M-theory 02-07-07 07:43 PM

''with my wife's hair dryer"

uh-huh, yeah ;)

Woebegone 10-05-07 02:49 AM

How about on a naked carbon fiber frame? I just bought an older frame with scratched up decals, but don't want to risk damaging the carbon with chemicals or excessive heat. Any ideas?

Woe

stronglight 10-05-07 07:18 AM

Some early decals were not a waterslide nor an adhesive backed type, nor were they clear coated, but they tended to survive very well. They were a varnish-set type (placed onto a wet clear varnish which had been applied on top of the enamel). These had a strong varnish coating on the actual transfer itself which gave the effect of being painted onto the bike once the paper backing was later soaked and removed. I think the only way those can be removed would be to chip and scrape them off as you would to remove spots of dried on enamel. I believe the head tube and seat tube transfers on my old Frejus is a good example of this type. They have chipped in spots over 35+ years, but still have the textured feel of hand painting over the beige enamel, and there is no question that they will not peel off - like the ol' 531 decals did, almost instantly.

http://farm2.static.flickr.com/1430/...176e15f5_m.jpg

bbattle 10-05-07 07:24 AM

The hairdryer won't hurt carbon fiber bikes.


All times are GMT -6. The time now is 12:00 PM.


Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.