eBay / CraigsList finds - "Are you looking for one of these!?" Part II
The dropped
Join Date: Oct 2018
Location: Columbus, OH
Posts: 2,406
Bikes: Pake C'Mute Touring/Commuter Build, 1989 Kona Cinder Cone, 1995 Trek 5200, 1973 Raleigh Super Course FG, 1960/61 Montgomery Ward Hawthorne "thrift" 3 speed, by Hercules (sold) : 1966 Schwinn Deluxe Racer (sold)
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1739 Post(s)
Liked 1,014 Times
in
696 Posts
IDK paint type... Car paint? Rattlecan Enamel? No clearcoat is all I can tell. It's slightly metallic, laid down well, but a little rough, as if nozzle was too far away, or coat was a bit too thin, like not "wet" enough.
Is acetone spilled a little at a time on a rag, then rubbed like mad on the frame considered "normal practice"???
Is acetone spilled a little at a time on a rag, then rubbed like mad on the frame considered "normal practice"???
The link gives you an idea about how tough the epoxy is. Those conditions will be difficult to recreate, and outside of a containment vessel, any acetone you use will evaporate before it can do much of anything to the Epoxy. Hopefully, the bike frame wasn't properly prepped, and the spray enamel should come off before you damage a clear coat too much.
Senior Member
Join Date: Sep 2019
Location: NPR, Florida
Posts: 124
Bikes: 1984~85 Raleigh Competition, 1985 Raleigh Super Course, 2013 Raleigh Revenio 2.0
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 43 Post(s)
Liked 35 Times
in
23 Posts
Likes For jreeves:
Senior Member
Join Date: May 2019
Location: Bloomington, IN
Posts: 2,724
Bikes: Paramount, Faggin, Ochsner, Ciocc, Basso
Mentioned: 107 Post(s)
Tagged: 0 Thread(s)
Quoted: 1197 Post(s)
Liked 1,636 Times
in
1,007 Posts
Unca Sam,
The paint stripper is a bad idea for cf. It will cause the matrix to break down and failure is almost a given at some point in time. CF is pretty tough as long as there are no scars or cuts in it. Finishes can be sanded off with 400/600/1000 grit papers with care being taken to just remove the paint layers. Tedious and time consuming but will allow for a good repaint. After all of the sanding a quick wipe down with acetone to clean off oils and debris and it will be ready to paint. Smiles,MH
The paint stripper is a bad idea for cf. It will cause the matrix to break down and failure is almost a given at some point in time. CF is pretty tough as long as there are no scars or cuts in it. Finishes can be sanded off with 400/600/1000 grit papers with care being taken to just remove the paint layers. Tedious and time consuming but will allow for a good repaint. After all of the sanding a quick wipe down with acetone to clean off oils and debris and it will be ready to paint. Smiles,MH
PM me your cotters
Join Date: Jun 2015
Location: ATL
Posts: 3,915
Mentioned: 80 Post(s)
Tagged: 0 Thread(s)
Quoted: 1136 Post(s)
Liked 586 Times
in
420 Posts
It's $300. Caveat: stuck stem. Who's going to be brave?
https://www.facebook.com/marketplace...1492168422572/
https://www.facebook.com/marketplace...1492168422572/
And among the "hey look over here" links - https://www.ebay.com/itm/193330224701 - No intel on this, just that the frame is a WTF
And on the Frenchie note, I've been eyeballing this, had deja vu when I first saw it but can't quite put my finger on why, maybe it was already listed in the past. Either way, it's pretty nice. It's totally my size but unless some freaking amazing human being is buying it for me, it ain't gonna land in my stable. Someone should buy it though!!
https://www.ebay.com/itm/Philippe-Bi...n/143371221830

__________________
███████████████
███████████████
Likes For francophile:
Senior Member
Join Date: Jan 2004
Location: Madison, WI USA
Posts: 6,692
Mentioned: 48 Post(s)
Tagged: 0 Thread(s)
Quoted: 2274 Post(s)
Liked 1,594 Times
in
1,101 Posts
Likes For madpogue:
Senior Member
Join Date: Nov 2013
Location: South of the Twin Cities, MN
Posts: 5,790
Mentioned: 29 Post(s)
Tagged: 1 Thread(s)
Quoted: 1111 Post(s)
Liked 2,194 Times
in
1,287 Posts
Banned
Join Date: Aug 2013
Posts: 7,150
Mentioned: 93 Post(s)
Tagged: 0 Thread(s)
Quoted: 1361 Post(s)
Likes: 0
Liked 418 Times
in
278 Posts
Actor Anthony LaPaglia is peddling a nice auction lot of classic lightweights this April 18, 2020.
Here's pics and info.
https://www.copakeauction.com/auctio...on-2020-04-18/
Amazing offerings but one can't help notice the set-ups and many with thrashed cables. Various sized frames and looks like he rode some of the larger than his normal fitted.
Here's pics and info.
https://www.copakeauction.com/auctio...on-2020-04-18/
Amazing offerings but one can't help notice the set-ups and many with thrashed cables. Various sized frames and looks like he rode some of the larger than his normal fitted.
Last edited by crank_addict; 02-11-20 at 09:55 PM.
Likes For crank_addict:
Senior Member
Join Date: Oct 2016
Location: San Mateo,Ca.
Posts: 4,308
Bikes: TRIMMED DOWN THE HERD
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1077 Post(s)
Liked 882 Times
in
575 Posts
Actor Anthony LaPaglia is peddling a nice auction lot of classic lightweights this April 18, 2020.
Here's pics and info.
https://www.copakeauction.com/auctio...on-2020-04-18/
Amazing offerings but one can't help notice the set-ups and many with thrashed cables. Various sized frames and looks like he rode some of the larger than his normal fitted.
Here's pics and info.
https://www.copakeauction.com/auctio...on-2020-04-18/
Amazing offerings but one can't help notice the set-ups and many with thrashed cables. Various sized frames and looks like he rode some of the larger than his normal fitted.
mycocyclist
Join Date: Dec 2016
Location: Monkey Junction, Wilmington, NC
Posts: 2,205
Bikes: 1964 Schwinn Paramount P-13 DeLuxe, 1964 Schwinn Sport Super Sport, 1972 Falcon San Remo, 1974 Maserati MT-1, 1974 Raleigh International, 1984 Lotus Odyssey, 198? Rossin Ghibli, 1990 LeMond Le Vanquer (sic), 1991 Specialized Allez Transition Pro, +
Mentioned: 23 Post(s)
Tagged: 0 Thread(s)
Quoted: 888 Post(s)
Liked 743 Times
in
422 Posts
Not My Bike - Too Distant For Me To Facilitate, Sorry
Villiers 1960’s Italian Road Race Bike - $125 (Richmond)
Posted 2020-02-11 23:32

"Italian road bike- 22” lugged lightweight steel frame, campagnolo deraileurs.
bicycle frame material: steel
bicycle type: road
frame size: 22”
wheel size: 27 in"
https://richmond.craigslist.org/bik/...073746919.html
Full Member
Join Date: Aug 2017
Location: San Mateo, CA
Posts: 416
Bikes: Bike Friday PRP, Bike Friday NWT, Bromton M6R, 1991 Miyata 914, 1991 Miyata 1000, 1986 Raleigh Portage, many more frames
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 200 Post(s)
Liked 332 Times
in
175 Posts
Not Craigslist or eBay, but maybe worth a look?
amateur
Handsome and not small Klein in NC
Klein Quantum 2 Mint Condition Pre Trek - $1000 (Greensboro)

https://greensboro.craigslist.org/bi...072414878.html
Senior Member
Join Date: Oct 2008
Location: Seattle
Posts: 1,438
Bikes: my precious steel boys
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 438 Post(s)
Liked 603 Times
in
359 Posts
Like New Schwinn Paramount 50 cm - $650 (Seattle)



Absolutely pristine 1987 USA made Schwinn Paramount. It's 50 cm or a hair smaller, metallic pink, and perfect. This is not the Japanese made Paramount (though those are also nice), it is the top-of-the-line Waterford made Paramount. On top of that, its new enough to have reasonably modern components . Save for a couple faint marks you wouldn't think this has ever been ridden. Look on EBAY, these regularly go for $1000+ and rival new bikes.
Cinella stem handlebars
Mavic Open 4 ceramic rims
New continental tires
DURA ACE drive train
DURA ACE brakes
Clip in pedals (not pictured)
https://seattle.craigslist.org/see/b...071882903.html
I'll be honest, as someone who's still kicking myself over not buying a cheap metallic pink "Magila Rosa Edition" Bianchi CdI a few years back, I kind of fancy this... if it were 52cm.
Senior Member
Join Date: Sep 2017
Location: Greenville SC
Posts: 4,047
Bikes: 1976 Motobecane Grand Jubile, 2020 Holdsworth Competition, 2022 Giant Trance 29 3
Mentioned: 42 Post(s)
Tagged: 0 Thread(s)
Quoted: 3179 Post(s)
Liked 3,334 Times
in
1,160 Posts
Someday...
Likes For abshipp:
Senior Member
Join Date: Sep 2017
Location: Greenville SC
Posts: 4,047
Bikes: 1976 Motobecane Grand Jubile, 2020 Holdsworth Competition, 2022 Giant Trance 29 3
Mentioned: 42 Post(s)
Tagged: 0 Thread(s)
Quoted: 3179 Post(s)
Liked 3,334 Times
in
1,160 Posts
Bikes are okay, I guess.
Join Date: Jan 2015
Location: Richmond, Virginia
Posts: 9,114
Bikes: Waterford Paramount Touring, Giant CFM-2, Raleigh Sports 3-speeds in M23 & L23, Schwinn Cimarron oddball build, Marin Palisades Trail dropbar conversion, Nishiki Cresta GT
Mentioned: 68 Post(s)
Tagged: 0 Thread(s)
Quoted: 2643 Post(s)
Liked 2,423 Times
in
1,543 Posts
Nothing fancy, but two mixtes, a Schwinn LeTour in 22" (pretty unusual, if you've ever tried to find one) and a smaller Nishiki. And don't tell me the Schwinn is not a true "mixte" frame.
https://www.facebook.com/marketplace...1301375491381/
https://www.facebook.com/marketplace...1301375491381/

Senior Member
Join Date: Oct 2018
Location: NH
Posts: 67
Bikes: '01 Klein Quantum, '91 GT Zaskar, '70s Di Lorenzo, '74 Gitane Champion du Monde, '50s Steyr Klunker, Cannondale Singlespeed
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 18 Post(s)
Likes: 0
Liked 21 Times
in
14 Posts
Senior Member
Join Date: Sep 2015
Location: Madison, WI
Posts: 2,676
Mentioned: 52 Post(s)
Tagged: 0 Thread(s)
Quoted: 1108 Post(s)
Liked 545 Times
in
305 Posts
Very nice top-end Lejeune for a decent price. 225 euros shipped to the US. 160 euros to Europe.
Possibly a Carre CV-6 ?
https://www.ebay.fr/itm/254508600322
Possibly a Carre CV-6 ?
https://www.ebay.fr/itm/254508600322

Last edited by TenGrainBread; 02-13-20 at 12:55 PM.
Senior Member
Join Date: Oct 2015
Location: PDX
Posts: 13,511
Bikes: Merz x 5 + Specialized Merz Allez x 2, Strawberry/Newlands/DiNucci/Ti x3, Gordon, Fuso/Moulton x2, Bornstein, Paisley,1958-74 Paramounts x3, 3rensho, 74 Moto TC, 73-78 Raleigh Pro's x5, Marinoni x2, 1960 Cinelli SC, 1980 Bianchi SC, PX-10 X 2
Mentioned: 260 Post(s)
Tagged: 0 Thread(s)
Quoted: 4311 Post(s)
Liked 5,766 Times
in
3,358 Posts
Nothing fancy, but two mixtes, a Schwinn LeTour in 22" (pretty unusual, if you've ever tried to find one) and a smaller Nishiki. And don't tell me the Schwinn is not a true "mixte" frame.
https://www.facebook.com/marketplace...1301375491381/

https://www.facebook.com/marketplace...1301375491381/



Likes For merziac:
Bikes are okay, I guess.
Join Date: Jan 2015
Location: Richmond, Virginia
Posts: 9,114
Bikes: Waterford Paramount Touring, Giant CFM-2, Raleigh Sports 3-speeds in M23 & L23, Schwinn Cimarron oddball build, Marin Palisades Trail dropbar conversion, Nishiki Cresta GT
Mentioned: 68 Post(s)
Tagged: 0 Thread(s)
Quoted: 2643 Post(s)
Liked 2,423 Times
in
1,543 Posts
1972? The Dura Mixte
And I'll take the opportunity to say here what I did not say there; "Sport" is a pretty lame label for this style, practically begging for a Who's On First exchange when discussing it:
"It's a Paris-Sport Sport."
"Sport sport?"
"Yes."
"No."
Senior Member
Join Date: Jun 2019
Location: Michigan USA
Posts: 809
Bikes: A bunch of old bikes.
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 226 Post(s)
Liked 718 Times
in
339 Posts
Been through this already days ago in the Dura thread. See post #13 .
1972? The Dura Mixte
And I'll take the opportunity to say here what I did not say there; "Sport" is a pretty lame label for this style, practically begging for a Who's On First exchange when discussing it:
"It's a Paris-Sport Sport."
"Sport sport?"
"Yes."
"No."
1972? The Dura Mixte
And I'll take the opportunity to say here what I did not say there; "Sport" is a pretty lame label for this style, practically begging for a Who's On First exchange when discussing it:
"It's a Paris-Sport Sport."
"Sport sport?"
"Yes."
"No."
We have one of each "variant" as defined by Sheldon Brown. Sheldon Brown's Glossary
It is much cleared to me that three sets of stays behind the seat tube would define the Mixte.
Much easier to search for instead of "Sport sport"
Senior Member
Join Date: Jan 2004
Location: Madison, WI USA
Posts: 6,692
Mentioned: 48 Post(s)
Tagged: 0 Thread(s)
Quoted: 2274 Post(s)
Liked 1,594 Times
in
1,101 Posts
^^^^^^ "Twixte"?
Likes For madpogue:
Senior Member
Join Date: Mar 2007
Location: SF Bay Area, East bay
Posts: 8,468
Bikes: Miyata 618 GT, Marinoni, Kestral 200 2002 Trek 5200, KHS Flite, Koga Miyata, Schwinn Spitfire 5, Mondia Special, Univega Alpina, Miyata team Ti, Santa Cruz Highball
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 1510 Post(s)
Liked 2,205 Times
in
1,072 Posts
https://sfbay.craigslist.org/sfc/bop...071720354.html
26” old school MTB wheels and tires - $70 (San Francisco)

Senior Member
Join Date: Jan 2010
Location: se MIch.
Posts: 2,619
Bikes: 1938 claud butler,1983 Basso,teledyne titan,teocali super,nrs,1993 stumpjumper fsr,Paramountain,Paramount Buell(sold),4 banger,Zaskar LE,Colnago Master Ibex MTB,1987ish,.etc....
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 686 Post(s)
Liked 2,401 Times
in
1,272 Posts
Senior Member
Join Date: Oct 2015
Location: PDX
Posts: 13,511
Bikes: Merz x 5 + Specialized Merz Allez x 2, Strawberry/Newlands/DiNucci/Ti x3, Gordon, Fuso/Moulton x2, Bornstein, Paisley,1958-74 Paramounts x3, 3rensho, 74 Moto TC, 73-78 Raleigh Pro's x5, Marinoni x2, 1960 Cinelli SC, 1980 Bianchi SC, PX-10 X 2
Mentioned: 260 Post(s)
Tagged: 0 Thread(s)
Quoted: 4311 Post(s)
Liked 5,766 Times
in
3,358 Posts
Been through this already days ago in the Dura thread. See post #13 .
1972? The Dura Mixte
And I'll take the opportunity to say here what I did not say there; "Sport" is a pretty lame label for this style, practically begging for a Who's On First exchange when discussing it:
"It's a Paris-Sport Sport."
"Sport sport?"
"Yes."
"No."
1972? The Dura Mixte
And I'll take the opportunity to say here what I did not say there; "Sport" is a pretty lame label for this style, practically begging for a Who's On First exchange when discussing it:
"It's a Paris-Sport Sport."
"Sport sport?"
"Yes."
"No."
Show off your Univega Alpina
So while not disagreeing, and lame or no, its what they came up with and what it is.
No idea who's on first.

Last edited by merziac; 02-13-20 at 10:24 AM.
Senior Member
Join Date: Jan 2004
Location: Madison, WI USA
Posts: 6,692
Mentioned: 48 Post(s)
Tagged: 0 Thread(s)
Quoted: 2274 Post(s)
Liked 1,594 Times
in
1,101 Posts