Torque Specs for SR BB and Crank arms?
#1
Senior Member
Thread Starter
Join Date: Dec 2013
Location: Bay Area, CA
Posts: 59
Bikes: 2011 Trek Rumblefish, 1993 Trek 5500, 2013 Salsa El Mariachi, 1982 Trek 412
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Torque Specs for SR BB and Crank arms?
Does anyone have instructions for torque specs or installation of an old Sakae Ringyo bb and crank arms? What is the torque on the square taper?
In reference to my bike:
Trek 412
In reference to my bike:
Trek 412
#2
Bianchi Goddess
Join Date: Apr 2009
Location: Shady Pines Retirement Fort Wayne, In
Posts: 27,858
Bikes: Too many to list here check my signature.
Mentioned: 192 Post(s)
Tagged: 2 Thread(s)
Quoted: 2930 Post(s)
Liked 2,923 Times
in
1,491 Posts
I don't think a lot people worried about torqueing stuff back then, I know I seldom saw a torque in the late '80s when I worked in a shop. I think the whole idea of torque specs on everything grew out of liability issues and replacement/warranty cost the last few years as more and more stuff is made from Ti and carbon fiber. I was always taught that if your using the correct wrench for the job once it stops moving the bolt/nut the torque is generally correct. Which is why a 6mm wrench is 8" long and 15mm is 13" long.
If your really want to torque them I think my early '90s Campi cranks call for around 25 ft lbs.
Nice looking project I guess it is coming back together?
If your really want to torque them I think my early '90s Campi cranks call for around 25 ft lbs.
Nice looking project I guess it is coming back together?
__________________
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
#3
Senior Member
Thread Starter
Join Date: Dec 2013
Location: Bay Area, CA
Posts: 59
Bikes: 2011 Trek Rumblefish, 1993 Trek 5500, 2013 Salsa El Mariachi, 1982 Trek 412
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Also, thats what I was planning on doing, I think my campy cranks on my trek 5500 were 32ft/lbs. I was going to do something similar. I could look up the torque specs for that particular size bolt and use engineering judgement too.
#4
Insane Bicycle Mechanic
Join Date: Mar 2008
Location: other Vancouver
Posts: 9,836
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 805 Post(s)
Liked 704 Times
in
376 Posts
Back when I was working in a Schwinn shop, we always had a card stuck to the wall of recommended torque values. Every new bike was checked with a torque wrench.
Park Tools has a reference for the most common torque values: https://www.parktool.com/blog/repair-...s-and-concepts
Park Tools has a reference for the most common torque values: https://www.parktool.com/blog/repair-...s-and-concepts
__________________
Jeff Wills
Comcast nuked my web page. It will return soon..
Jeff Wills
Comcast nuked my web page. It will return soon..
#5
Senior Member
Thread Starter
Join Date: Dec 2013
Location: Bay Area, CA
Posts: 59
Bikes: 2011 Trek Rumblefish, 1993 Trek 5500, 2013 Salsa El Mariachi, 1982 Trek 412
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Thanks Jeff! Looks like right around 300 in/lbs will do fine.
#7
Senior Member
The Barnett's manual says that if the manufacturer's specs are not available, then follow this for both left and right: "Torque nut/bolt to 390in-lbs (32.5ft-lbs, or 65lbs@6" or 50lbs@8")."
I've usually used one of my three torque wrenches, but I've usually stopped bit short of those specs just because it "felt" right. This discretion included my one set of SR cranks. But (ironically?) it was the SR that I had to torqued down later as it had started to drift off the spline on the drive side. No bother since then. So, I'd recommend the 32 or so ft-lbs.
I've usually used one of my three torque wrenches, but I've usually stopped bit short of those specs just because it "felt" right. This discretion included my one set of SR cranks. But (ironically?) it was the SR that I had to torqued down later as it had started to drift off the spline on the drive side. No bother since then. So, I'd recommend the 32 or so ft-lbs.
__________________
Vitus 979, Simplon 4 Star, Gazelle Champion Mondial, Woodrup Giro, Dawes Atlantis
Vitus 979, Simplon 4 Star, Gazelle Champion Mondial, Woodrup Giro, Dawes Atlantis
#8
Senior Member
Join Date: May 2010
Location: Bastrop Texas
Posts: 4,478
Bikes: Univega, Peu P6, Peu PR-10, Ted Williams, Peu UO-8, Peu UO-18 Mixte, Peu Dolomites
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 965 Post(s)
Liked 1,629 Times
in
1,045 Posts
Hope this will help...
https://www.bikeforums.net/showthread...e-Torque-Specs
Remember I extracted this info for good old steel bikes - Not for composite or Weird graph/plastic components...
Or especially " hydride Al2CuHx " ...
https://www.bikeforums.net/showthread...e-Torque-Specs
Remember I extracted this info for good old steel bikes - Not for composite or Weird graph/plastic components...
Or especially " hydride Al2CuHx " ...
__________________
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
Last edited by zandoval; 12-30-13 at 11:54 AM.