Catastrophic mechanical failure!
#1
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Toronto, CANADA
Posts: 6,204
Bikes: ...a few.
Mentioned: 47 Post(s)
Tagged: 0 Thread(s)
Quoted: 2012 Post(s)
Liked 409 Times
in
235 Posts
Catastrophic mechanical failure!
I was two kilometers from home, riding in front of my wife. I was accompanying her to the yoga studio and then I would ride off to the grocery store. I noticed a rattling noise from the front wheel. I saw that the fender stay was loose. These are the fendrs: SKS Velo 42 Urban Mudguard Set | Chain Reaction Cycles
Anyway, I thought, I'll fix that when I get to the studio. No big deal. Well, it turned out it was a big deal. The stay came out of the clip, got caught in the lugs of the tires (which were recently mounted CX tires, wider and beefier than the urban touring tires I had ridden for the couple of years). The next thing I knew I was flying over the handlebar. The bike flipped over with me on it. That's how my wife described it watching from about 30 yards back. I was going maybe 25 km/h, possibly faster. I landed on my shoulder first, then my head hit the pavement. For those of you who've had serious crashes you know that the feeling is quite surreal afterwards, because you are never expecting it to happen.
My wife rode her bike home, got the minivan, and came back to pick me up.
Post-incident analysis:
1. My own negligence is to blame, first and foremost, because I should have stopped the bike right there an then to fix the stay. Also, I have inspected the clearance after mounting the CX tires and noticed that there was less clearance and that the lugs might cause a problem.
2. Discounting (1), because it wasn't even on my mind to do that this crash could have happened anywhere at any time, sort of like a ticking time bomb. The crash happened on a quiet, wide residential street and my wife was there with me. So I am lucky in that sense. It could have happened on a much busier street and I could have been going much faster, perhaps on a descent doing 40 km/h.
3. The injury I suffered is a badly bruised shoulder. There's probably some ligament and tendon damage, and perhaps fractured bone. I haven't gone for x-ray. Doctor says to wait a few days and see how it is before going to do the irradiation. Also a sprained thumb on the other hand. A piece of foam has chipped off on the inside of the helmet, but I don't think there is any serious head trauma. I did not lose consciousness. Immediately after the crash I got up and rolled on to the grassy curb. Still in total disbelief and shock.
Next Steps:
The bike is still in the van. I will have to have a look at it as soon as I have the use of my shoulder, which at the moment is still very sore and painful to move. I think I will ride without front fenders from now on.
Rest. I will be driving to work the next few weeks until everything heals.
The one positive thing I can take away from this is that other vehicles or the condition of the road were non-factors. I can't be so complacent with the maintenance of my bikes. Constant vigilance, not just while riding, but also with regular inspection and anticipating problems with your own machine.
Thanks for reading. I know it was long.
Anyway, I thought, I'll fix that when I get to the studio. No big deal. Well, it turned out it was a big deal. The stay came out of the clip, got caught in the lugs of the tires (which were recently mounted CX tires, wider and beefier than the urban touring tires I had ridden for the couple of years). The next thing I knew I was flying over the handlebar. The bike flipped over with me on it. That's how my wife described it watching from about 30 yards back. I was going maybe 25 km/h, possibly faster. I landed on my shoulder first, then my head hit the pavement. For those of you who've had serious crashes you know that the feeling is quite surreal afterwards, because you are never expecting it to happen.
My wife rode her bike home, got the minivan, and came back to pick me up.
Post-incident analysis:
1. My own negligence is to blame, first and foremost, because I should have stopped the bike right there an then to fix the stay. Also, I have inspected the clearance after mounting the CX tires and noticed that there was less clearance and that the lugs might cause a problem.
2. Discounting (1), because it wasn't even on my mind to do that this crash could have happened anywhere at any time, sort of like a ticking time bomb. The crash happened on a quiet, wide residential street and my wife was there with me. So I am lucky in that sense. It could have happened on a much busier street and I could have been going much faster, perhaps on a descent doing 40 km/h.
3. The injury I suffered is a badly bruised shoulder. There's probably some ligament and tendon damage, and perhaps fractured bone. I haven't gone for x-ray. Doctor says to wait a few days and see how it is before going to do the irradiation. Also a sprained thumb on the other hand. A piece of foam has chipped off on the inside of the helmet, but I don't think there is any serious head trauma. I did not lose consciousness. Immediately after the crash I got up and rolled on to the grassy curb. Still in total disbelief and shock.
Next Steps:
The bike is still in the van. I will have to have a look at it as soon as I have the use of my shoulder, which at the moment is still very sore and painful to move. I think I will ride without front fenders from now on.
Rest. I will be driving to work the next few weeks until everything heals.
The one positive thing I can take away from this is that other vehicles or the condition of the road were non-factors. I can't be so complacent with the maintenance of my bikes. Constant vigilance, not just while riding, but also with regular inspection and anticipating problems with your own machine.
Thanks for reading. I know it was long.
#2
Banned
Join Date: Feb 2008
Location: Mississauga/Toronto, Ontario canada
Posts: 8,721
Bikes: I have 3 singlespeed/fixed gear bikes
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 4227 Post(s)
Liked 2,488 Times
in
1,286 Posts
I am glad to hear that you're ok. It could of been much worse if it happened in heavy traffic...Personally I like to have some extra clearance between my fenders and tires. I am also using Planet Bike fenders, they don't have any clips to come loose, once they are tightened they stay tight, no problems ever coming loose...The only catastrophic failure I've ever had was when my crank arm broke on my fixed gear bike.
#3
Senior Member
No need to give up the front fender. Just be more diligent in your maintenance. Any funny sound on my bike and I stop to figure out what it is. Crashing sucks. Lesson learned the hard way, but you'll never forget.
#5
Me duelen las nalgas
Join Date: Aug 2015
Location: Texas
Posts: 13,513
Bikes: Centurion Ironman, Trek 5900, Univega Via Carisma, Globe Carmel
Mentioned: 199 Post(s)
Tagged: 0 Thread(s)
Quoted: 4559 Post(s)
Liked 2,802 Times
in
1,800 Posts
Ouch. Watch for unusual headaches, changes in pupil sizes, etc. Sometimes there's a delay before complications from head knocks set in. Be sure to let your wife know to watch for this stuff as well, because complications from concussions can make it impossible for the victim to take any rational decisions.
And every time I think about installing fenders on my bike I read about incidents like this. I don't ride in rain often enough to matter. I think I'll just keep getting wet the handful of times a year I'm riding in the rain. In fact I just finished wiping off the mud spatter from last week's rain. I might opt for a downtube mud guard instead. The rear rack already blocks most of the wet gunk anyway.
And every time I think about installing fenders on my bike I read about incidents like this. I don't ride in rain often enough to matter. I think I'll just keep getting wet the handful of times a year I'm riding in the rain. In fact I just finished wiping off the mud spatter from last week's rain. I might opt for a downtube mud guard instead. The rear rack already blocks most of the wet gunk anyway.
#6
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18374 Post(s)
Liked 4,509 Times
in
3,351 Posts
Look at your collarbone (clavicle) and shoulder positioning carefully.
Make sure everything more or less works, and then good luck for a speedy recovery.
Time for the N+1 Bicycle purchase?
Make sure everything more or less works, and then good luck for a speedy recovery.
Time for the N+1 Bicycle purchase?
#7
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Toronto, CANADA
Posts: 6,204
Bikes: ...a few.
Mentioned: 47 Post(s)
Tagged: 0 Thread(s)
Quoted: 2012 Post(s)
Liked 409 Times
in
235 Posts
Ouch. Watch for unusual headaches, changes in pupil sizes, etc. Sometimes there's a delay before complications from head knocks set in. Be sure to let your wife know to watch for this stuff as well, because complications from concussions can make it impossible for the victim to take any rational decisions.
And every time I think about installing fenders on my bike I read about incidents like this. I don't ride in rain often enough to matter. I think I'll just keep getting wet the handful of times a year I'm riding in the rain. In fact I just finished wiping off the mud spatter from last week's rain. I might opt for a downtube mud guard instead. The rear rack already blocks most of the wet gunk anyway.
#8
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Toronto, CANADA
Posts: 6,204
Bikes: ...a few.
Mentioned: 47 Post(s)
Tagged: 0 Thread(s)
Quoted: 2012 Post(s)
Liked 409 Times
in
235 Posts
Now how's that going to help??!!
#9
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Toronto, CANADA
Posts: 6,204
Bikes: ...a few.
Mentioned: 47 Post(s)
Tagged: 0 Thread(s)
Quoted: 2012 Post(s)
Liked 409 Times
in
235 Posts
I had a chance to assess the damage to the bike. The top of the rear rack is bent as is one of the vertical supports. The rear fender is also bent, beyond repair, I am afraid. The rear of the bike must have impacted on the pavement quite forcefully to do that. The right side shifter was turned slightly.
So the nearest I can figure when the front wheel seized I tumbled forward. The bike probably flipped once, with the right shifter making contact with the pavement first, then the rear end came down.
So the nearest I can figure when the front wheel seized I tumbled forward. The bike probably flipped once, with the right shifter making contact with the pavement first, then the rear end came down.
#12
Standard Member
Join Date: Apr 2009
Location: Brunswick, Maine
Posts: 4,268
Bikes: 1948 P. Barnard & Son, 1962 Rudge Sports, 1963 Freddie Grubb Routier, 1980 Manufrance Hirondelle, 1983 F. Moser Sprint, 1989 Raleigh Technium Pre, 2001 Raleigh M80
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 1297 Post(s)
Liked 940 Times
in
490 Posts
Make sure you let us know of your progress. (I'm glad your wife was riding a good distance behind). It's strange that SKS would design something like this. I am not sure what you mean by "lugs", though.
#13
Senior Member
Join Date: Dec 2001
Location: New Jersey
Posts: 7,143
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 261 Post(s)
Likes: 0
Liked 11 Times
in
10 Posts
I would have taken the x-ray right after the accident. You suffered a once in a lifetime accident that requires an x-ray for broken bones and other damage. This is not the time to worry about cancer 40 years down the road.
You discovered the danger of the front fender the hard way. There are fenders that are supposed to break lose when something like this happens. However, I don't believe you had one of those fenders.
If you Google "Front fender & accident", you'll see a number of horror stories. The one that come to my mind are the accidents involving ride share bikes like Citibike that come with fenders. The lawsuit states that Citibikes have a defective front fender but that is not the case. The front fender has a slight inherent danger that every cyclist must be aware of. In the case of Citibike, the rider suffered a crushed face.
After my accident, I will never use a front fender. There are people who use them for decades and nothing happens. However, when it does go wrong, it's a life changing moment you'll never forget.
Please, get an x-ray.
#14
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Toronto, CANADA
Posts: 6,204
Bikes: ...a few.
Mentioned: 47 Post(s)
Tagged: 0 Thread(s)
Quoted: 2012 Post(s)
Liked 409 Times
in
235 Posts
CX tires have more aggressive treads for traction on gravel, dirt, mud, etc. These treads, at least on my tires, protrude out more off to the side, presumably to improve traction on loose surfaces. It was one of this features which I believe caught hold of the fender stay, carried it until it hit the fork, then it stopped.
#15
Senior Member
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,904
Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4806 Post(s)
Liked 3,928 Times
in
2,553 Posts
I consider any failure forward of mid top tube and mid down tube to be treated as potentially fatal. I have been very lucky. That said, the almost incredible string of luck that kept me from becoming a vegetable or dead instead meant a head injury that cost me my profession and many opportunities. Two years later I happened to be riding the old incredibly stiff Weinmann Concave rims in the wide 1 1/4" width when a fellow rider put his quick realease in my front wheel in a 30 mph + town line sprint. I rode the bike to a stop with 8 consecutive right side spokes cut out. If I had been riding my sewup wheels, a half dozen guys behind me would have piled on.
My deck has no more magic Jokers so I try to do my best to not temp fate any more.
Ben
My deck has no more magic Jokers so I try to do my best to not temp fate any more.
Ben
#16
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Toronto, CANADA
Posts: 6,204
Bikes: ...a few.
Mentioned: 47 Post(s)
Tagged: 0 Thread(s)
Quoted: 2012 Post(s)
Liked 409 Times
in
235 Posts
You were very very lucky.
I would have taken the x-ray right after the accident. You suffered a once in a lifetime accident that requires an x-ray for broken bones and other damage. This is not the time to worry about cancer 40 years down the road.
You discovered the danger of the front fender the hard way. There are fenders that are supposed to break lose when something like this happens. However, I don't believe you had one of those fenders.
If you Google "Front fender & accident", you'll see a number of horror stories. The one that come to my mind are the accidents involving ride share bikes like Citibike that come with fenders. The lawsuit states that Citibikes have a defective front fender but that is not the case. The front fender has a slight inherent danger that every cyclist must be aware of. In the case of Citibike, the rider suffered a crushed face.
After my accident, I will never use a front fender. There are people who use them for decades and nothing happens. However, when it does go wrong, it's a life changing moment you'll never forget.
Please, get an x-ray.
I would have taken the x-ray right after the accident. You suffered a once in a lifetime accident that requires an x-ray for broken bones and other damage. This is not the time to worry about cancer 40 years down the road.
You discovered the danger of the front fender the hard way. There are fenders that are supposed to break lose when something like this happens. However, I don't believe you had one of those fenders.
If you Google "Front fender & accident", you'll see a number of horror stories. The one that come to my mind are the accidents involving ride share bikes like Citibike that come with fenders. The lawsuit states that Citibikes have a defective front fender but that is not the case. The front fender has a slight inherent danger that every cyclist must be aware of. In the case of Citibike, the rider suffered a crushed face.
After my accident, I will never use a front fender. There are people who use them for decades and nothing happens. However, when it does go wrong, it's a life changing moment you'll never forget.
Please, get an x-ray.
I have a set of MK2 fenders on one of my other bikes, and upon close inspection I believe that on the very small chance that the stay or any part of that fender were to fail and come in contact with the wheel or the spokes the thin plastic would just break, likely resulting in a bent spoke or just broken fender. I don't believe that it could halt the forward progress of the front wheel the way the metal stay would. Now if I were using slick tires, I would have been fine too.
I'd put on about 150 km on this setup prior to the accident, mostly off road on gravel tracks. Had this happened off road it may have even been worse as there wouldn't have been anyone around to help.
#17
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Toronto, CANADA
Posts: 6,204
Bikes: ...a few.
Mentioned: 47 Post(s)
Tagged: 0 Thread(s)
Quoted: 2012 Post(s)
Liked 409 Times
in
235 Posts
I consider any failure forward of mid top tube and mid down tube to be treated as potentially fatal. I have been very lucky. That said, the almost incredible string of luck that kept me from becoming a vegetable or dead instead meant a head injury that cost me my profession and many opportunities. Two years later I happened to be riding the old incredibly stiff Weinmann Concave rims in the wide 1 1/4" width when a fellow rider put his quick realease in my front wheel in a 30 mph + town line sprint. I rode the bike to a stop with 8 consecutive right side spokes cut out. If I had been riding my sewup wheels, a half dozen guys behind me would have piled on.
My deck has no more magic Jokers so I try to do my best to not temp fate any more.
Ben
My deck has no more magic Jokers so I try to do my best to not temp fate any more.
Ben
#18
Member
Join Date: Apr 2016
Location: Capital District NY
Posts: 38
Bikes: Dahon C7a
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I'm one of those guys that has used fenders and never had a problem. But I can relate to your call for diligence. I will take the lesson here to heart and make certain to do a pre-ride check on my entire bike before pedaling off. Glad you're okay (at least per your post).
#19
Senior Member
Join Date: Apr 2014
Location: Austin, TX
Posts: 284
Bikes: Motobecane
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Fenders aren't worth either the hassles involved in tire size and clearance, or the danger they represent. For the 2-3 days a year when I might get mud spattered, I just throw a change of clothes in the panniers. When I'm riding in the rain, fenders are no use to me anyway as I don't bring a poncho and I'm going to be soaked regardless.
#20
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,707
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5781 Post(s)
Liked 2,576 Times
in
1,427 Posts
That was exactly how my first serious bicycle accident happened some 50 years ago, except that I wasn't aware of a loose front fender brace. Like the OP, I escaped with no serious injury, but the bike didn't do as well. The brace wound around the axle and pulled the rim in so the front wheel looked like Ms Pacman.
This kind of failure is why we don't see many single wire loop fender braces anymore. Where they are used, the practice is to pass them around the outside of the fender, so they can't get snagged on the rolling tire.
This kind of failure is why we don't see many single wire loop fender braces anymore. Where they are used, the practice is to pass them around the outside of the fender, so they can't get snagged on the rolling tire.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
#21
Senior Member
Join Date: Jun 2007
Location: Minneapolis
Posts: 8,101
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 52 Post(s)
Likes: 0
Liked 17 Times
in
13 Posts
https://www.amazon.com/SKS-Front-Fen.../dp/B001N84RHU
Not sure it would have prevented your accident but they came with my fenders. I had a rear fender come loose, get caught in the tire and fold up like an accordion. Of course anything with the rear wheel has minor consequences compared to the front.
It's not just fenders though. My son had an eerily similar incident and injuries when he was going about the same speed and a stick got caught in his spokes. He landed on his shoulder and helmet. No structural damage to his shoulder but he got a bad case of road rash on that and his ankle. Still has the scars and it's been at least 3 years. The steel fork looked like a noodle but only a single spoke broke on the wheel.
A friend also had a pretty bad incident when she got too close to the rider in front of her and their wheels made contact with each other. Lets just say that that one took a lot of trips to the dentist before she was back to normal. Broken wrist too if I remember right.
So yeah, it's best if front wheels don't stop rolling. I don't know that I would write off fenders completely but there's some risks with knobby tires, minimal clearance and struts that don't break away that you're now aware of. You can fix those things. Your story made me double check my fenders but I'm pretty much ready to take them off for the summer anyway.
Here's hoping you have a speedy recovery, - both physically and psychologically. That kind of thing leaves a lasting impact on your psyche.
Not sure it would have prevented your accident but they came with my fenders. I had a rear fender come loose, get caught in the tire and fold up like an accordion. Of course anything with the rear wheel has minor consequences compared to the front.
It's not just fenders though. My son had an eerily similar incident and injuries when he was going about the same speed and a stick got caught in his spokes. He landed on his shoulder and helmet. No structural damage to his shoulder but he got a bad case of road rash on that and his ankle. Still has the scars and it's been at least 3 years. The steel fork looked like a noodle but only a single spoke broke on the wheel.
A friend also had a pretty bad incident when she got too close to the rider in front of her and their wheels made contact with each other. Lets just say that that one took a lot of trips to the dentist before she was back to normal. Broken wrist too if I remember right.
So yeah, it's best if front wheels don't stop rolling. I don't know that I would write off fenders completely but there's some risks with knobby tires, minimal clearance and struts that don't break away that you're now aware of. You can fix those things. Your story made me double check my fenders but I'm pretty much ready to take them off for the summer anyway.
Here's hoping you have a speedy recovery, - both physically and psychologically. That kind of thing leaves a lasting impact on your psyche.
Last edited by tjspiel; 06-19-16 at 10:35 PM.
#22
Senior Member
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,904
Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4806 Post(s)
Liked 3,928 Times
in
2,553 Posts
... So what kinds of things do you do to mitigate this risk, because all kinds of things could happen on the front end? Blowing a tire? Though depending on the speed one could possibly maintain control and glide to a stop on the rim. Broken spoke? Again, you could likely maintain control and come to a stop. Broken front axle? Fractured carbon fork? Brake failure? But not likely both brakes. What other catastrophic failure would there be?
Broken front axles are very rare and if you have a quick release, you won't even know it until you pull the wheel off. Broken spoke? Not an issue as long as you have lots. (I won't ride some of the new forks with very close fits to small racing size tires. No space above the tire just means that only small tires canm be used. No space to the side means that a broken spoke could vbe a real issue. And on a low spoke racing wheel? See my post above about that guy taking out my spokes in a sprint. If I had one of those forks, that ride would have ended quite differently.) Fractured carbon fiber fork. Not an issue for me. I leave them in the store. All my forks are steel and will be. Brake failures that matter here are almost always due to negligence. (I do not ride brakes I won't trust my life to, especially on my bikes that will see real hills.) I do my best to stay on top of my brakes and pads adjustment and condition, especially the front.
Thanks for bringing this up. I just realized it is that time of year when considering brake/rim heat on long descents with hard braking can be an issue. One of the smart preventative moves is to let a little air out of the tires before heading down. But that does require advance thought.
Ben
#23
Senior Member
Join Date: Apr 2014
Location: Austin, TX
Posts: 284
Bikes: Motobecane
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Broken spoke? Not an issue as long as you have lots. (I won't ride some of the new forks with very close fits to small racing size tires. No space above the tire just means that only small tires canm be used. No space to the side means that a broken spoke could vbe a real issue. And on a low spoke racing wheel? See my post above about that guy taking out my spokes in a sprint. If I had one of those forks, that ride would have ended quite differently.) Fractured carbon fiber fork. Not an issue for me. I leave them in the store. All my forks are steel and will be. Brake failures that matter here are almost always due to negligence. (I do not ride brakes I won't trust my life to, especially on my bikes that will see real hills.) I do my best to stay on top of my brakes and pads adjustment and condition, especially the front.
I'm lucky - I hit a pothole straight-on with my first bike when I was seven years old, and face planted into the asphalt. Got a bloody lip, a bloody nose, and a life-long lesson in respecting the bike and the road.
#24
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Toronto, CANADA
Posts: 6,204
Bikes: ...a few.
Mentioned: 47 Post(s)
Tagged: 0 Thread(s)
Quoted: 2012 Post(s)
Liked 409 Times
in
235 Posts
Fenders aren't worth either the hassles involved in tire size and clearance, or the danger they represent. For the 2-3 days a year when I might get mud spattered, I just throw a change of clothes in the panniers. When I'm riding in the rain, fenders are no use to me anyway as I don't bring a poncho and I'm going to be soaked regardless.
#25
Senior Member
Thread Starter
Join Date: Jul 2014
Location: Toronto, CANADA
Posts: 6,204
Bikes: ...a few.
Mentioned: 47 Post(s)
Tagged: 0 Thread(s)
Quoted: 2012 Post(s)
Liked 409 Times
in
235 Posts
To be honest I stayed away from the forum a few days because I didn't want to be reminded of the incident. It's still very fresh in my mind, obviously, but coming back on here does help. Life is not without risks, and when you get blind-sided like this it does make you take notice. I think psychologically I am fine to get back on the saddle. Physically, it may be some time.