Tail light with threaded mount.
I am looking for a good tail light with a threaded mount that i can use on my rear rack bracket. It doesn't look like the Planet bike superflash has one. I know the LD1000 doesn't because i own one. I've been using Xenon lightman strobes for years, but am finally giving up on them, because they fail at an alarming rate.
I just bought a new one to replace a defective one, and it was DOA. Thanks for any tips. |
The Topeak Redlight comes with a mounting kit for attaching to Topeak racks...don't know if it will fit others, though...
http://www.bikesmart.com/products/LITTOP_red.jpg |
B&M makes several that mount that way.
4DToplight Permanent $26.50 (has an on-off switch) 4DToplight Senso $36. (on-off switch and auto on sensor) http://www.peterwhitecycles.com/imag.../dtop-perm.jpg The two lights look the same and only differ in their switches. Peter White carries both. Link--about 3/4 down the page. Make sure you get the battery powered versions and not the dynamo versions. |
Originally Posted by Portis
I am looking for a good tail light with a threaded mount that i can use on my rear rack bracket. It doesn't look like the Planet bike superflash has one. I know the LD1000 doesn't because i own one. I've been using Xenon lightman strobes for years, but am finally giving up on them, because they fail at an alarming rate.
I just bought a new one to replace a defective one, and it was DOA. Thanks for any tips. |
Originally Posted by cyccommute
If you take the clip off of the LD1000, there is a pin mount and screw hole behind it. At least there was on mine. I have one mounted to the back of a rack currently.
http://xs412.xs.to/xs412/07086/IMG_5850.JPG http://xs412.xs.to/xs412/07086/IMG_5851.JPG There are no threads like there are on my Lightman strobes. I just used a threaded bolt and screwed into the plastic threaded housing. I'm hoping i can move this 1000 to the bracket and put a superflash on my trunk bag via the belt clip. |
anything with a CSPC approved reflector (and many that don't) shoud mount on a standard reflector bracket so they should be compatable with your rack. My CatEye (can't remember model number) with the CSPC reflector has that style mount and so does the Blackburn Mars 2.0
|
Originally Posted by Portis
Here is what's behind mine.
There are no threads like there are on my Lightman strobes. I just used a threaded bolt and screwed into the plastic threaded housing. I'm hoping i can move this 1000 to the bracket and put a superflash on my trunk bag via the belt clip. http://i144.photobucket.com/albums/r...e/IMG_0272.jpg http://i144.photobucket.com/albums/r...e/IMG_0275.jpg And here it is off the bike http://i144.photobucket.com/albums/r...e/IMG_0277.jpg |
Thanks for posting those pics. Very helpful. :)
|
I'm a bit of a "belt and suspenders" guy, which is a good thing considering the potholes we have.
For some TL-LD1000, I designed a bracket by sawing and filing bits off a 2" x 2" x 6" aluminium angle bracket. I was able to screw the TL-LD1000 the same way Cyccommute did. Then, I added one zip tie on each side of the attachment point (between each vertical row of lights), around the light and metal bracket. The Planet Bike Superflash can be installed in a fairly similar fashion. If you remove its bracket, it has a clip that looks a bit like a ball-point clip. Since there is some room left in the casing itself, I have clipped two Superflashes on my daughter's bike, then I drilled tiny holes through the casing, metal bracket and clip, then I used a tiny #4 or #6 bolt to secure the light in place. Alternate way. The Superflash also comes with a seatpost collar and a much smaller seatstay clamp. If you cut the rubber shims to double them up, the seatstay clamp fits quite well around the legs of a typical rear rack (Blackburn, Axiom...). It's not the ideal solution if you ride in the snow (light gets dirty very quickly) or if you have panniers, but it would work fine with a rack trunk or other stuff on the rack. |
Originally Posted by Portis
Thanks for posting those pics. Very helpful. :)
|
I just used a short peace of PVC plumbing pipe and fender washers through my rack reflector mount as shown in the picture.
http://img172.imageshack.us/img172/6694/pict0075qk6.jpg If you look closely you will notice the pipe is cut at an angle corresponding to the angle of a standard seat tube. This allows the blinkie to be aimed properly as the indentations in the clamp would not allow any angle to be selected. I have over 4,000 miles on this blinkie setup with no problems with the mount or blinkie. BTW that’s a cheap BELL blinkie from Wal-mart that’s too cheap for a thief to bother with. |
It is safe to drill a pilot hole through the back of the LD1000 into the battery compartment (remember to remove the batteries). I believe I used the next larger size drill bit over the 1/8." Anyway, you will not hit any electronics or components in the modification and allows the use of a full length reflector screw for added strength.
|
Originally Posted by n4zou
BTW that’s a cheap BELL blinkie from Wal-mart that’s too cheap for a thief to bother with.
|
Originally Posted by LandLuger
It is safe to drill a pilot hole through the back of the LD1000 into the battery compartment (remember to remove the batteries). I believe I used the next larger size drill bit over the 1/8." Anyway, you will not hit any electronics or components in the modification and allows the use of a full length reflector screw for added strength.
The screw hole on the light is actually threaded, but you can't see it without a bright light. It is a tight interference fit to lock the screw in place. |
Originally Posted by Portis
I am looking for a good tail light with a threaded mount that i can use on my rear rack bracket.
It has an integrated reflector as well. I have it screwed to my rack at all times. I do have the Superflash as well though. Tal. |
Originally Posted by 2manybikes
Using washers will allow you to use any length screw you want without drilling.
The screw hole on the light is actually threaded, but you can't see it without a bright light. It is a tight interference fit to lock the screw in place. |
if your seatpost is longer than it needs to be you can just cut the bottom of it off, drill a hole and mount it to the rack. otherwise the blackburn mars 2.0, as already mentioned, mounts quickly and painlessly to a reflector bracket.
|
Originally Posted by tlupfer
if your seatpost is longer than it needs to be you can just cut the bottom of it off, drill a hole and mount it to the rack. otherwise the blackburn mars 2.0, as already mentioned, mounts quickly and painlessly to a reflector bracket.
|
|
All times are GMT -6. The time now is 02:09 PM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.