Go Back  Bike Forums > Bike Forums > Commuting
Reload this Page >

Working on your bike while at work

Notices
Commuting Bicycle commuting is easier than you think, before you know it, you'll be hooked. Learn the tips, hints, equipment, safety requirements for safely riding your bike to work.

Working on your bike while at work

Old 10-11-07, 09:16 AM
  #1  
Senior Member
Thread Starter
 
dannyq's Avatar
 
Join Date: May 2006
Location: Halifax, N.S. Canada
Posts: 135

Bikes: 2005 Opus Solo

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Working on your bike while at work

I just finished levelling out my saddle a bit after I noticed the nose was up to much after this morning's ride to work. I started to wonder, what's the biggest repair/maintenance job you ever did on your bike while at work?

Last edited by dannyq; 10-11-07 at 09:31 AM.
dannyq is offline  
Old 10-11-07, 09:28 AM
  #2  
rhm
multimodal commuter
 
rhm's Avatar
 
Join Date: Nov 2006
Location: NJ, NYC, LI
Posts: 19,852

Bikes: 1940s Fothergill, 1959 Allegro Special, 1963? Claud Butler Olympic Sprint, Lambert 'Clubman', 1974 Fuji "the Ace", 1976 Holdsworth 650b conversion rando bike, 1983 Trek 720 tourer, 1984 Counterpoint Opus II, 1993 Basso Gap, 2010 Downtube 8h, and...

Mentioned: 584 Post(s)
Tagged: 0 Thread(s)
Quoted: 1908 Post(s)
Liked 574 Times in 339 Posts
I had to do repairs on my Strida lots of times, but the Strida is a bit of an unusual beastie anyway, so some of the repairs I had to do are not quite as complicated as they are on a 'real' bike. At any rate I replaced a headset bearing once, the belt drive once, and the bottom bracket spindle and chainring (they call it a pulley!) at least twice, and of course flat tires now and then.

More recently I'm riding a more conventional bike... and I've had to do flat tires, gear adjustments, futzing with headlight/taillight wires, etc. lots of times.
rhm is offline  
Old 10-11-07, 09:53 AM
  #3  
Senior Member
 
Join Date: Oct 2005
Posts: 198
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I haven't actually done any bike repair at work, yet.

That being said, given the amazing amount of time people spend "going to the bathroom" or "going upstairs for a coke", I can't see how anyone could make an argument against spending 5-10 minutes adjusting or fixing something on your bike.

That is, of course, assuming that you aren't a bathroom/coker/loiter.
jonathan180iq is offline  
Old 10-11-07, 09:58 AM
  #4  
Pedaled too far.
 
Artkansas's Avatar
 
Join Date: Oct 2005
Location: La Petite Roche
Posts: 12,851
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 11 Post(s)
Likes: 0
Liked 7 Times in 7 Posts
Originally Posted by dannyq
I just finished levelling out my saddle a bit after I noticed the nose was up to much after this morning's ride to work. I started to wonder, what's the biggest repair/maintenance job you ever did on your bike while at work?
I unpacked it out of a box and assembled it from the parts.
Artkansas is offline  
Old 10-11-07, 10:08 AM
  #5  
SERENITY NOW!!!
 
jyossarian's Avatar
 
Join Date: Aug 2005
Location: In the 212
Posts: 8,738

Bikes: Haro Vector, IRO Rob Roy, Bianchi Veloce

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 1 Time in 1 Post
I swapped the bb, cranks, RD and headset from one bike to another yesterday.
__________________
HHCMF - Take pride in your ability to amaze lesser mortals! - MikeR



We demand rigidly defined areas of doubt and uncertainty!
jyossarian is offline  
Old 10-11-07, 10:13 AM
  #6  
Trans-Urban Velocommando
 
ax0n's Avatar
 
Join Date: Nov 2006
Location: Lenexa, KS
Posts: 2,400

Bikes: 06 Trek 1200 - 98 DB Outlook - 99 DB Sorrento

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I've patched about 5 innertubes at my desk, but not all at once. Most of the problems I can fix out in the wild pretty quickly, so I don't bother waiting until I get to work to tighten something up or adjust something.

When I get a flat on my way to work, I usually swap the tube out for one of my spares, then patch the punctured one at my desk and put it back on the bike to use the next time I get a flat.
ax0n is offline  
Old 10-11-07, 10:18 AM
  #7  
Thread Killer
 
evblazer's Avatar
 
Join Date: May 2007
Location: Marfan Syndrome-Clyde-DFW, TX
Posts: 1,845

Bikes: Fuji Touring Xtracycle, Merlin Road, Bacchetta Giro 26 (Sold), Challenge Hurricane, Cruzbike Sofrider

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I had to adjust my Rear D yesterday which got some really weird looks. Don't know what it's issue is but lately it doesn't want to stay adjusted for a whole trip before it starts slipping and attempting to shift between gears without really shifting. Could mean never get it right in the first place I guess.
A little wheel truing and brake adjustments are usually the most I have gotten into.
evblazer is offline  
Old 10-11-07, 10:27 AM
  #8  
Senior Member
 
Join Date: Jun 2007
Posts: 365
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Originally Posted by Artkansas
I unpacked it out of a box and assembled it from the parts.
Excellent!


I keep a pump and tools here. I've done all sorts of fit adjustments, wheel maintaineance, and tune-ups, but nothing serious.

Heck, I have parts shipped to my office so I don't have to bring them from home
RadioFlyer is offline  
Old 10-11-07, 10:30 AM
  #9  
Plays in Traffic
 
1ply's Avatar
 
Join Date: Mar 2006
Location: Kitchener, Ontario
Posts: 484
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Sure makes my removal of the front pads to give them a little scuffing on some sandpaper look like nothing at all. Yep, it's the most I've done at work.

you try to remove your front brakes on your car at lunch wiseguy
1ply is offline  
Old 10-11-07, 10:38 AM
  #10  
B-b-b-b-b-b-bicicle Rider
 
orange leader's Avatar
 
Join Date: Apr 2005
Location: Racine WI
Posts: 749

Bikes: 1997, stumpjumper S-works hardtail, Medici, Giant Perigee(track dropouts and fixed gear), Columbia twosome, schwinn twinn, '67 raleigh 5 speed internal hub, Old triumph 3 speed, old BSA 3-speed, schwinn Racer 2spd kickback, Broken raysport criteriu

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Liked 5 Times in 3 Posts


After a (then) 9 mile ride to work on Halloween, I had to replace the knee joint hinge AND the femur-pelvis spindle, AND the knee-handlebar rubber band.
orange leader is offline  
Old 10-11-07, 10:48 AM
  #11  
Senior Member
 
Join Date: Oct 2005
Posts: 14,277
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 3 Times in 3 Posts
Just adjusting my brakes. Lately my coworkers frequently see me at my desk swapping tubes out and patching them.
DataJunkie is offline  
Old 10-11-07, 10:52 AM
  #12  
Dirty old man in training
 
Join Date: Aug 2004
Location: Cary NC
Posts: 455

Bikes: 2007 Novara Randonee, 1991 Raleigh Olympian, 1988 Nishiki Ariel

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
On a bike? So far just adjust the saddle.

Back in college I replaced the starter in my 82 Tercel by myself in the parking lot between classes one evening. Took about 80 minutes to fix the car, and 20 minutes in the men's room to scrub the grime from my hands.
Chuck G is offline  
Old 10-11-07, 10:53 AM
  #13  
Trans-Urban Velocommando
 
ax0n's Avatar
 
Join Date: Nov 2006
Location: Lenexa, KS
Posts: 2,400

Bikes: 06 Trek 1200 - 98 DB Outlook - 99 DB Sorrento

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by 1ply
you try to remove your front brakes on your car at lunch wiseguy
I did my front pads and rotors on my Escort over lunch in work clothes about 5 years ago. I also did an oil change (laying on my back with jackstands) for a co-worker over lunch once. But I wore coveralls and mechanics gloves for that. By day, I'm a UNIX system administrator and info-security guy, not a mechanic.
ax0n is offline  
Old 10-11-07, 11:53 AM
  #14  
...there I was...
 
bloodhound's Avatar
 
Join Date: Jun 2006
Location: ...I left Hawaii for this? This is frickin cold!...
Posts: 204

Bikes: ...Surly LHT - blue...

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
...minor stuff...

Nothing major: derailleur adjustments, tire patches, brake adjustments, fitting adjustments, tightening loose stuff, temporary repairs.

But, in my office of 10 people, there are 5 bikes... so there is always something being done.

Just this morning, one guy patched a tube, then repatched after finding the rest of the thorn during inflation. Another guy performed a temporary repair to a rear fender.

Yesterday I had to adjust my rear deraileur due to accidentally messing with it during a tube repair on the way in to work.

So, there's always something going on...
bloodhound is offline  
Old 10-11-07, 11:59 AM
  #15  
One Man Fast Brick
 
hubcap's Avatar
 
Join Date: Jun 2005
Location: Chicagoland
Posts: 1,121

Bikes: Specialized Langster, Bianchi San Jose, early 90s GT Karakoram, Yuba Mundo, Mercier Nano (mini velo), Nashbar Steel Commuter, KHS Tandemania Sport

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Nothing really major. I've added some fenders to a bike and removed/degreased/cleaned/reinstalled a chain.
hubcap is offline  
Old 10-11-07, 12:31 PM
  #16  
Blasted Weeds
 
Tude's Avatar
 
Join Date: Aug 2006
Location: Rochester, NY
Posts: 1,182

Bikes: Trek 1200C, Specialized Rockhopper, Giant Yukon FX, Giant Acapulco

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Fixed a flat better (didn't like how the tube went in), minor adjustments, prepped and cleaned the bike for an off road ride right after work, put some new pedals on that I had just picked up from the LBS around the corner.
Tude is offline  
Old 10-11-07, 12:35 PM
  #17  
Trans-Urban Velocommando
 
ax0n's Avatar
 
Join Date: Nov 2006
Location: Lenexa, KS
Posts: 2,400

Bikes: 06 Trek 1200 - 98 DB Outlook - 99 DB Sorrento

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Why would you clean a bike for an offroad ride? Just asking.
ax0n is offline  
Old 10-11-07, 01:16 PM
  #18  
Cat None
 
SDRider's Avatar
 
Join Date: Aug 2005
Location: San Diego
Posts: 4,508

Bikes: LOOK KG 461, LeMond Zurich, Giant Talon 29er 0

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I retaped the handlebars on a friend's bike while at work once. It took all of about 10 minutes tops.

Other than that, just minor adjustments and checking tire inflation before the ride home (I keep an extra floor pump under my desk).
SDRider is offline  
Old 10-11-07, 01:23 PM
  #19  
Senior Member
 
Join Date: Jun 2006
Posts: 1,117

Bikes: ANT Club Racer, 2004 Trek 520

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I had a chain snap while stomping my way up the hill to work. Fortunately, it was only 50 yards from the building, so my walk of shame wasn't too far. Used a chain breaker to pop out the broken link and shorten the chain and rode home.
spokenword is offline  
Old 10-11-07, 01:24 PM
  #20  
Senior Member
 
thdave's Avatar
 
Join Date: Nov 2005
Posts: 2,242
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I've commandeered the men's bathroom a half dozen times to fix flats.
thdave is offline  
Old 10-11-07, 01:30 PM
  #21  
Cat None
 
SDRider's Avatar
 
Join Date: Aug 2005
Location: San Diego
Posts: 4,508

Bikes: LOOK KG 461, LeMond Zurich, Giant Talon 29er 0

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by spokenword
I had a chain snap while stomping my way up the hill to work. Fortunately, it was only 50 yards from the building, so my walk of shame wasn't too far. Used a chain breaker to pop out the broken link and shorten the chain and rode home.
Did you go down when the chain broke? That's kind of scary...how many miles did you have on the chain?
SDRider is offline  
Old 10-11-07, 01:32 PM
  #22  
Membership Not Required
 
wahoonc's Avatar
 
Join Date: Jan 2005
Location: On the road-USA
Posts: 16,855

Bikes: Giant Excursion, Raleigh Sports, Raleigh R.S.W. Compact, Motobecane? and about 20 more! OMG

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 70 Post(s)
Likes: 0
Liked 15 Times in 14 Posts
Today...installed a new tire on my dingy/lifeboat bike and reworked a bottom bracket on the plant bike (I am temporarily assigned to work at an Alcoa plant, we ride bicycles to get around )

Aaron
__________________
Webshots is bailing out, if you find any of my posts with corrupt picture files and want to see them corrected please let me know. :(

ISO: A late 1980's Giant Iguana MTB frameset (or complete bike) 23" Red with yellow graphics.

"Cycling should be a way of life, not a hobby.
RIDE, YOU FOOL, RIDE!"
_Nicodemus

"Steel: nearly a thousand years of metallurgical development
Aluminum: barely a hundred
Which one would you rather have under your butt at 30mph?"
_krazygluon
wahoonc is offline  
Old 10-11-07, 02:20 PM
  #23  
Senior Member
 
Join Date: Apr 2006
Location: San Jose, CA
Posts: 1,840

Bikes: Bianchi San Remo - set up as a utility bike, Peter Mooney Road bike, Peter Mooney commute bike,Dahon Folder,Schwinn Paramount Tandem

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I Keep a set of tools at work, and park my bike in an empty cube next to my cube (gloat). I generally spend a few minutes cleaning and doing minor adjustments right after I have arrived, while waiting to cool down and stop sweating before going into the shower. Typically I don't do any more maintenance than brake or derailler adjustment, perhaps a bit of lubrication.
sauerwald is offline  
Old 10-11-07, 02:25 PM
  #24  
Senior Member
 
shumacher's Avatar
 
Join Date: Oct 2006
Location: Hammond, LA
Posts: 305

Bikes: 95 Specialized Rockhopper Comp, 92 Specialized Sirrus Triple

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I have all shipments delivered to work. I've had a case of sake, some odd looking shoes, panniers, fenders, some slightly less odd looking shoes, a God, The Devil, and Bob DVD...

I'm thinking about buying a bike trailer and having it shipped to work. I'd probably just haul it to my office and let it sit till quitting time. I'd then take the phone off the hook, build up the trailer, hitch it to the bike and ride home. I can't imagine there'd be any issue. I'd be a little hesitant of going any larger than that though. I'd have a whole bike shipped to a friend's house. I don't like UPS leaving stuff in front of my apartment while I'm at work.
shumacher is offline  
Old 10-11-07, 02:26 PM
  #25  
Senior Member
 
Join Date: Oct 2005
Posts: 14,277
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 3 Times in 3 Posts
On that thought I am about ready to purchase a cheap floor pump and keep it in my desk. It seems 3/4 of the times I get flats are at work.
DataJunkie is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.