Alignment...
#1
Junior Member
Thread Starter
Join Date: Jul 2008
Location: San Carlos/ San Francisco
Posts: 6
Bikes: Bianchi: San Jose
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Alignment...
For the past few weeks I have been feeling like my alignment is off, I have adjusted my handlebars to try and match up with my front tire many times but i still feel like its off. I am wondering if anyone knows a good way to determine if ones bike is aligned and ways to fix. If it matters i ride a 2008 Bianchi San Jose.
#2
Senior Member
Join Date: Jan 2008
Location: SW Florida
Posts: 121
Bikes: Surly Karate Monkey, Nashbar MTN "Frame", 96' GT Avalanche, Jamis Dakota
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
More likely your bar is tweeked. try a new bar.
#3
Light Makes Right
Join Date: Apr 2005
Location: Green Mountain, Colorado
Posts: 1,520
Bikes: Gianni Motta Criterium, Dean Hardtail
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Are you sure YOU are aligned? At one point I was certain that all three of my bikes were out of alignment. All of them "pulled" to the left when I took my hands off the bars. Then I realized that all three couldn't be out of alignment in the same way and took myself to the chiropractor.
Just a thought......
Just a thought......
#5
Junior Member
Thread Starter
Join Date: Jul 2008
Location: San Carlos/ San Francisco
Posts: 6
Bikes: Bianchi: San Jose
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Are you sure YOU are aligned? At one point I was certain that all three of my bikes were out of alignment. All of them "pulled" to the left when I took my hands off the bars. Then I realized that all three couldn't be out of alignment in the same way and took myself to the chiropractor.
Just a thought......
Just a thought......
#6
Junior Member
Thread Starter
Join Date: Jul 2008
Location: San Carlos/ San Francisco
Posts: 6
Bikes: Bianchi: San Jose
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#7
Junior Member
Thread Starter
Join Date: Jul 2008
Location: San Carlos/ San Francisco
Posts: 6
Bikes: Bianchi: San Jose
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#8
Senior Member
Join Date: Aug 2007
Location: Central TX
Posts: 583
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 5 Post(s)
Likes: 0
Liked 6 Times
in
3 Posts
You can take them off the bike and place them on a known flat surface like a countertop then look for discrepancies between the two ends in relation to the flat surface and each other. Maybe try a couple different positions since I'm sure your bars aren't exactly straight and some curvature to them. I did this with some motorcycle handlebars I thought were slightly tweaked and it proved to be true!
#9
Senior Member
Join Date: Jan 2008
Location: SW Florida
Posts: 121
Bikes: Surly Karate Monkey, Nashbar MTN "Frame", 96' GT Avalanche, Jamis Dakota
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
You can take them off the bike and place them on a known flat surface like a countertop then look for discrepancies between the two ends in relation to the flat surface and each other. Maybe try a couple different positions since I'm sure your bars aren't exactly straight and some curvature to them. I did this with some motorcycle handlebars I thought were slightly tweaked and it proved to be true!