![]() |
Bike lights on mup
I do some of my commute on the minute man bike path, less than a mile with 3 street crossings. I run 2 minewt 100 minis, one on the bar and one on the helmet. Also a minewt mini 150 in blink mode , kinda bright. Had a ped yell at me, " lights too bright". I also encounter ninja walkers, ipod zombies and bikers with no lights or reflectors. So where is the balance? Generally the commute is pleasant with walkers and bikers doing their own thing properly. I would rather err on the side of too much rather than not enough light.
|
i'm glad the lakefront path here in chicago is illuminated with street lights, or in this case MUP lights ;)
|
Can you adjust your lights to a dimmer setting? I believe in bright lights, but I don't always run the lights on high. Low is enough for plenty of situations,IMHO.
|
There are two reasons for lights: to see and to be seen. Blinking lights are good for being seen and steady lights are good for seeing. On a MUP, you don't need the blinkies. Switch the blinkies to steadies when you're not near a road crossing and it'll be much nicer on the peds eyes.
|
If your lights are "too bright," then they know where you are. Don't worry about them, worry about you.
|
Yes, Multi Use Paths lights, harr, hee.
|
Originally Posted by lostarchitect
(Post 13543790)
If your lights are "too bright," then they know where you are. Don't worry about them, worry about you.
When you see another rider approaching from the front just put one hand over your bar light and make sure you're looking down or away from approaching riders. It's courteous and safer. |
Originally Posted by DiabloScott
(Post 13543893)
When you see another rider approaching from the front just put one hand over your bar light and make sure you're looking down or away from approaching riders. It's courteous and safer.
|
I run 2 ..and one on the helmet. when you look that way.. turn it off, perhaps, and/or, re-locate it onto the bike too.. |
Originally Posted by DiabloScott
(Post 13543893)
When you see another rider approaching from the front just put one hand over your bar light and make sure you're looking down or away from approaching riders. It's courteous and safer.
When I get blinded by oncoming light, I lose track of both the edge of the pavement and the center -- so I'm not sure if I'll accidentally veer into the rider who's blinding me. |
I usually try to make sure my lights are angled down a bit, are dimmed if possible, and I only have small lights on my helmet (if at all). If I'm riding in traffic, that changes.
|
Originally Posted by BarracksSi
(Post 13543937)
Almost every time I cover or re-aim my light in similar situations, I hear, "Thank you."
When I get blinded by oncoming light, I lose track of both the edge of the pavement and the center -- so I'm not sure if I'll accidentally veer into the rider who's blinding me. |
Originally Posted by BarracksSi
(Post 13543937)
Almost every time I cover or re-aim my light in similar situations, I hear, "Thank you."
When I get blinded by oncoming light, I lose track of both the edge of the pavement and the center -- so I'm not sure if I'll accidentally veer into the rider who's blinding me. My lights are fine for the trail, not too bright and they're aimed down at the ground - I cover them as a clue to the oncoming rider to do the same but it usually doesn't work. I understand the appeal of helmet lights but I don't think most of the users get it. Recently a lot of joggers are using headband lights or something that are almost as bad. |
|
On MUPs I ride with just enough light (pointed down) to see the trail ahead of me (either two Fenix LD20s or a single Niterider Mininewt 350.) Helmet light gets switched off on MUPs.
|
Originally Posted by DiabloScott
(Post 13543893)
When you see another rider approaching from the front just put one hand over your bar light and make sure you're looking down or away from approaching riders. It's courteous and safer.
|
Originally Posted by DiabloScott
(Post 13543893)
If your lights are too bright, they can reduce the ability of the oncoming rider to see the road... this happens to me all the time on the path. I'm looking for the side of the path and judging the distance between myself and the other people on the trail and if a bright light is in my eyes I almost have to come to a stop; this is especially a problem with helmet lights because people tend to shine them in my face.
When you see another rider approaching from the front just put one hand over your bar light and make sure you're looking down or away from approaching riders. It's courteous and safer. |
Originally Posted by DiabloScott
(Post 13543893)
If your lights are too bright, they can reduce the ability of the oncoming rider to see the road... this happens to me all the time on the path. I'm looking for the side of the path and judging the distance between myself and the other people on the trail and if a bright light is in my eyes I almost have to come to a stop; this is especially a problem with helmet lights because people tend to shine them in my face.
When you see another rider approaching from the front just put one hand over your bar light and make sure you're looking down or away from approaching riders. It's courteous and safer. This is not a problem of the lights being too bright, but rather that the light is not directed properly. It should be focused some distance on the road directly ahead of you, with minimal spill (particular up spill)... If done so, then almost no amount is too bright. |
My headlight although bright shouldn't cause problems as it is aimed low. My tail light might be an annoyance but I rarely encounter anyone else on the path in the dark this time of year. The rear light is on my rack, so I have to get off the bike to switch it, which I'd probably do if anyone else was around.
I encountered a guy crouched holding his dog this morning. He was practically invisible, but at least he saw me coming. I usually look for regions that are slightly darker than the surroundings, but often mistake garbage cans for pedestrians. |
my primary light is fork mounted, and difficult to safely reach on curvy, bumpy, MUPs. i realize it can be very bright, but hope that oncoming people have the brains enough to not act like deer and stare into the white. my light has no dual-brightness mode (unless you count turning it off and draining the capacitor---very difficult to do safely while moving). the beam is shaped/focused, but on MUPs is still bright enough to stun kids smoking pot in the darkness. too bad for them.
when it happens that i encounter another bright light (car or bicycle), i use the visor on my helmet to block the brunt of it and keep focused on the edge of the road or path. this always works for me. always. if it happens that you can't see the path, then you need to slow or stop to evaluate that condition, and not fault some other user's light. that's part of riding on varying road conditions. on the other hand, if it's some moron with a headlamp aimed directly at my eyes, i have the option of returning the favor with my helmet-mounted light. it's my version of flashing my brights at another car. all in all, i approve of bright lights on the bicycles, and live with the consequences of others who feel the same. worse things can happen (like road salmoning with dark clothes and no lights at night). |
I have a solution, but you and many people here may not like it: don't ride on MUPs.
|
Originally Posted by Leebo
(Post 13543651)
I do some of my commute on the minute man bike path, less than a mile with 3 street crossings. I run 2 minewt 100 minis, one on the bar and one on the helmet. Also a minewt mini 150 in blink mode , kinda bright. Had a ped yell at me, " lights too bright". I also encounter ninja walkers, ipod zombies and bikers with no lights or reflectors. So where is the balance? Generally the commute is pleasant with walkers and bikers doing their own thing properly. I would rather err on the side of too much rather than not enough light.
|
If you can, aim your headlights down on the MUP, turn off your blinker, and don't look directly at anyone if you've got a headlamp on. If you can't, come to terms with the fact that you kind of suck.
Originally Posted by pwdeegan
(Post 13544624)
when it happens that i encounter another bright light (car or bicycle), i use the visor on my helmet to block the brunt of it and keep focused on the edge of the road or path. this always works for me. always. if it happens that you can't see the path, then you need to slow or stop to evaluate that condition, and not fault some other user's light. that's part of riding on varying road conditions.
Originally Posted by cellery
(Post 13545519)
I have a solution, but you and many people here may not like it: don't ride on MUPs.
But cars and trucks suck to share the road with, in my opinion more so than any of the minor annoyances found on the MUP, since none of these pose a threat to my life (except for the moose, maybe). And for every moment of minor annoyance, I'm pretty sure that there is at least an hour of pleasant, scenic, stress free cycling as well. |
Originally Posted by myrridin
(Post 13544367)
This is not a problem of the lights being too bright, but rather that the light is not directed properly. It should be focused some distance on the road directly ahead of you, with minimal spill (particular up spill)... If done so, then almost no amount is too bright.
|
Originally Posted by lostarchitect
(Post 13543790)
If your lights are "too bright," then they know where you are. Don't worry about them, worry about you.
|
| All times are GMT -6. The time now is 09:32 PM. |
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.