East coast winter gloves?
#1
Senior Member
Thread Starter
Join Date: Jun 2014
Posts: 104
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
East coast winter gloves?
Looking for recommendations on winter gloves for an NYC winter of commuting. Would prefer to have something fairly thin (not looking for lobster gloves) with longer wrist coverage. Was considering something similar (if not) these: Castelli | An Unfair Advantage - Product details
Cheers
Cheers
#2
Senior Member
Join Date: Feb 2013
Location: NYC
Posts: 476
Bikes: Schwinn World Sport Jamis Ventura
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Here is what I do, they're not thin but the work really well! I have a pair of grippy heavy winter/snow gloves and I put my thin running gloves with smartscreen touch pads inside the heavy gloves. This allows me to use my phone , take on and take off my locks without having to expose my skin to the air. It's the best and cheapest solution I've yet to find.
#3
Senior Member
Join Date: Jan 2009
Location: Colorado Springs, CO
Posts: 5,973
Bikes: 2015 Charge Plug, 2007 Dahon Boardwalk, 1997 Nishiki Blazer, 1984 Nishiki International, 2006 Felt F65, 1989 Dahon Getaway V
Mentioned: 54 Post(s)
Tagged: 0 Thread(s)
Quoted: 1364 Post(s)
Liked 1,677 Times
in
827 Posts
Here is what I do, they're not thin but the work really well! I have a pair of grippy heavy winter/snow gloves and I put my thin running gloves with smartscreen touch pads inside the heavy gloves. This allows me to use my phone , take on and take off my locks without having to expose my skin to the air. It's the best and cheapest solution I've yet to find.
#4
Let's Ride!
Join Date: Jul 2008
Location: Triad, NC USA
Posts: 2,569
Bikes: --2010 Jamis 650b1-- 2016 Cervelo R2-- 2018 Salsa Journeyman 650B
Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 327 Post(s)
Liked 37 Times
in
24 Posts
those are a nice looking pair of gloves. I tend use two pairs of gloves. I have aero tech wind proof gloves and then i put some soft shell or wool liners inside the gloves. I like the options of multipair versus one pair. It helps to regulate temperature too.
#7
Plays in traffic
Join Date: May 2006
Location: Rochester, NY
Posts: 6,971
Bikes: 1996 Litespeed Classic, 2006 Trek Portland, 2013 Ribble Winter/Audax, 2016 Giant Talon 4
Mentioned: 21 Post(s)
Tagged: 0 Thread(s)
Quoted: 76 Post(s)
Likes: 0
Liked 14 Times
in
9 Posts
^^^ Exactly this. ^^^
For my inner pair, I wear summer-weight full-finger MTB gloves in size large. Then I wear and extra-large pair of "cold weather" (read: Who cycles below freezing?) windproof, gloves for the outers. This combo gets me down to the mid-teens F. I can still work the STI levers just fine, and if I do need more dexterity, I still have the inner glove on.
For my inner pair, I wear summer-weight full-finger MTB gloves in size large. Then I wear and extra-large pair of "cold weather" (read: Who cycles below freezing?) windproof, gloves for the outers. This combo gets me down to the mid-teens F. I can still work the STI levers just fine, and if I do need more dexterity, I still have the inner glove on.
#8
Aspiring curmudgeon
Join Date: Aug 2014
Location: Saint Louis
Posts: 2,486
Bikes: Guerciotti, Serotta, Gaulzetti
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 111 Post(s)
Likes: 0
Liked 26 Times
in
13 Posts
I use these Rivendell half-mitts over regular fingerless cycling gloves. They're easy to take off when I need dexterity.
__________________
"Party on comrades" -- Lenin, probably
"Party on comrades" -- Lenin, probably
#9
Bye Bye
Join Date: Jul 2005
Location: Gone gone gone
Posts: 3,677
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Happy with the Planet Bike Borealis, they have a liner that you can swap in and out with your own gloves to tune the temp.
Borealis
For really cold, and with a flat bar. I use a set of pogies:
IMG_2391 by mbeganyi, on Flickr
by mbeganyi, on Flickr
These are cheap ATV ones from the hunting section... but they work. I usually just wear a thin liner glove.
Borealis
For really cold, and with a flat bar. I use a set of pogies:
IMG_2391 by mbeganyi, on Flickr
by mbeganyi, on Flickr
These are cheap ATV ones from the hunting section... but they work. I usually just wear a thin liner glove.
__________________
So long. Been nice knowing you BF.... to all the friends I've made here and in real life... its been great. But this place needs an enema.
So long. Been nice knowing you BF.... to all the friends I've made here and in real life... its been great. But this place needs an enema.
#10
Senior Member
Fleece, windproof gloves, I like the EMS versions but any outdoor/sports store should have them.
#12
Senior Member
Join Date: Aug 2012
Location: Lancaster, PA, USA
Posts: 1,851
Bikes: 2012 Trek Allant, 2016 Bianchi Volpe Disc
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I wear cheap ski gloves with Glo-Gloves stretched over top. Keeps my hands warm down to around 15F for my 30 minute commute. If it's over 30F, I'll wear some fleece mittens instead. The mitten part can flip back to reveal fingerless gloves.
#13
contiuniously variable
These might help?
Auclair 4-Way Stretch Fleece Gloves - Recycled Polyester (For Men) - Save 66%
I have some thin recycled polyester gloves i got at macy's back in 2009. They need mending, but are absolutely amazing & can fit into both my thicker gloves and my snow gloves.
- Andy
Auclair 4-Way Stretch Fleece Gloves - Recycled Polyester (For Men) - Save 66%
I have some thin recycled polyester gloves i got at macy's back in 2009. They need mending, but are absolutely amazing & can fit into both my thicker gloves and my snow gloves.
- Andy
#14
Junior Member
Join Date: Oct 2014
Posts: 7
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I went to the old school leather store on bleecker st. just east of sixth ave. and bought some deerskin gloves. They have them lined or unlined. I actually have both styles. I think they're light warm and flexible, kind of ideal. I also have merino liners that work with either pair.
#15
aka Tom Reingold
Join Date: Jan 2009
Location: New York, NY, and High Falls, NY, USA
Posts: 40,503
Bikes: 1962 Rudge Sports, 1971 Raleigh Super Course, 1971 Raleigh Pro Track, 1974 Raleigh International, 1975 Viscount Fixie, 1982 McLean, 1996 Lemond (Ti), 2002 Burley Zydeco tandem
Mentioned: 511 Post(s)
Tagged: 0 Thread(s)
Quoted: 7348 Post(s)
Liked 2,465 Times
in
1,433 Posts
I went to the old school leather store on bleecker st. just east of sixth ave. and bought some deerskin gloves. They have them lined or unlined. I actually have both styles. I think they're light warm and flexible, kind of ideal. I also have merino liners that work with either pair.
__________________
Tom Reingold, tom@noglider.com
New York City and High Falls, NY
Blogs: The Experienced Cyclist; noglider's ride blog
“When man invented the bicycle he reached the peak of his attainments.” — Elizabeth West, US author
Please email me rather than PM'ing me. Thanks.
Tom Reingold, tom@noglider.com
New York City and High Falls, NY
Blogs: The Experienced Cyclist; noglider's ride blog
“When man invented the bicycle he reached the peak of his attainments.” — Elizabeth West, US author
Please email me rather than PM'ing me. Thanks.
#16
Banned
Join Date: Feb 2008
Location: Mississauga/Toronto, Ontario canada
Posts: 8,721
Bikes: I have 3 singlespeed/fixed gear bikes
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 4227 Post(s)
Liked 2,488 Times
in
1,286 Posts
Two layers is the only thing that keeps my hands warm during the coldest days. I use a pair of thin lightweight gloves made from wool or fleece with heavier mitts over it. In my experience mitts is the only thing that works on longer rides during very cold weather.
#17
Senior Member
Happy with the Planet Bike Borealis, they have a liner that you can swap in and out with your own gloves to tune the temp.
Borealis
For really cold, and with a flat bar. I use a set of pogies:
IMG_2391 by mbeganyi, on Flickr
by mbeganyi, on Flickr
These are cheap ATV ones from the hunting section... but they work. I usually just wear a thin liner glove.
Borealis
For really cold, and with a flat bar. I use a set of pogies:
IMG_2391 by mbeganyi, on Flickr
by mbeganyi, on Flickr
These are cheap ATV ones from the hunting section... but they work. I usually just wear a thin liner glove.
I have them for my road bike. Completely wipes out the whole glove controversy. I use the same thin gloves I use at 40-50F inside of the Bar Mitts and my hands stay nice and warm, dexterity is terrific, and the fooling around with gloves is over. It's really tough to get a pair of gloves that are going to work right when they on on your hands, out there in a 20mph steady wind at cold temps. I don't think there is a glove on the planet that will hold up to that for long periods of time (I have some experience in this - I'm used to working at outside at extreme low temps down as far as -30F).
I get the ones designed for older shimano (i.e. brake cables not routed under the tape) even though I have the new style. The reason is that they have a zipper to let you get the brake cables through. Even though I don't need that, the zipper allows me to open them up a bit when it's warmer and let some cooling air in. Yep, that's right - they can be too warm.
I will use these when the temp is sustained at 30-40F or so and then lower. Then I wear a very light fleece glove by Pearl Izumi that breathes well but has some windproofness.
J.
#18
Senior Member
Join Date: Feb 2014
Location: Kent Wa.
Posts: 5,332
Bikes: 2005 Gazelle Golfo, 1935 Raleigh Sport, 1970 Robin Hood sport, 1974 Schwinn Continental, 1984 Ross MTB/porteur, 2013 Flying Piegon path racer, 2014 Gazelle Toer Populair T8
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 396 Post(s)
Likes: 0
Liked 8 Times
in
7 Posts
#19
Senior Member
Join Date: Jul 2008
Location: 25 miles northwest of Boston
Posts: 29,549
Bikes: Bottecchia Sprint, GT Timberline 29r, Marin Muirwoods 29er, Trek FX Alpha 7.0
Mentioned: 112 Post(s)
Tagged: 0 Thread(s)
Quoted: 5224 Post(s)
Liked 3,581 Times
in
2,342 Posts
gloves, can't have enough, just bought a pair this weekend, it's my addiction. for winter commuting though my favorite combo was separate glove liners (high quality) and roomy winter gloves. when it was 17 degrees I added a chemical warmer pack. I wasn't riding urban though so I was able to occasionally curl up some fingers and blow into the outer gloves to rewarm them switching off from one hand to the other when necessary
#20
Senior Member
Join Date: Sep 2014
Location: Boston
Posts: 927
Bikes: Death machines all
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 297 Post(s)
Liked 86 Times
in
63 Posts
Being a fashionable city guy I need elegant riding apparel, comfort and function is secondary.
These work gloves are nicely insulated, and I find having the reflective back improves visibility from ahead of the bike when hands are on the flat bars, and for signaling lane changes.
These work gloves are nicely insulated, and I find having the reflective back improves visibility from ahead of the bike when hands are on the flat bars, and for signaling lane changes.
__________________
Work is the curse of the drinking classes - Oscar Wilde
Work is the curse of the drinking classes - Oscar Wilde
#21
don't try this at home.
Join Date: Jan 2006
Location: N. KY
Posts: 5,940
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 974 Post(s)
Liked 512 Times
in
352 Posts
I don't commute, but my hands get cold easily. I've tried lots of gloves, including some goretex windproof ski gloves. The ski gloves still left me with cold hands below 40F.
Now I have some different layers to combine.
1. REI glove liners. I just bought a second pair of these, in case REI stops selling them. These are really thin, and but somewhat wind resistant. They actually fit under my fingerless gloves, and that's a great combination at 55-60F. They have a smooth surface, so they are easy to fit inside other gloves.
2. "Windblocking" fleece gloves. I tried them alone in past years, but they weren't too warm. But I wore them last weekend with the thin liner gloves at 45F, and they worked great. My hands don't get damp from sweat. And I removed the liners when it got to 50F.
3. Marmot shell gloves. These are windproof and have a thin fleecy lining. They are sized quite a bit larger, to fit liner gloves. REI sold these in previous years, but I don't see them at REI online now.
I've worn these shells with thin liners and with fleece liners. The liners can get pretty wet from sweat, but dry pretty fast when removed from the shells. And if it warms up, the shells can be worn by themselves. It's nice that I can wash the liners and dry them quickly, and just air dry the shells, no washing needed.
The long cuffs keep cold air off my wrists and jacket cuffs. And the tether loops let me pull off the shells and let them hang if I need temporary finger dexterity with just the liners.
Now I have some different layers to combine.
1. REI glove liners. I just bought a second pair of these, in case REI stops selling them. These are really thin, and but somewhat wind resistant. They actually fit under my fingerless gloves, and that's a great combination at 55-60F. They have a smooth surface, so they are easy to fit inside other gloves.
2. "Windblocking" fleece gloves. I tried them alone in past years, but they weren't too warm. But I wore them last weekend with the thin liner gloves at 45F, and they worked great. My hands don't get damp from sweat. And I removed the liners when it got to 50F.
3. Marmot shell gloves. These are windproof and have a thin fleecy lining. They are sized quite a bit larger, to fit liner gloves. REI sold these in previous years, but I don't see them at REI online now.
I've worn these shells with thin liners and with fleece liners. The liners can get pretty wet from sweat, but dry pretty fast when removed from the shells. And if it warms up, the shells can be worn by themselves. It's nice that I can wash the liners and dry them quickly, and just air dry the shells, no washing needed.
The long cuffs keep cold air off my wrists and jacket cuffs. And the tether loops let me pull off the shells and let them hang if I need temporary finger dexterity with just the liners.
Last edited by rm -rf; 11-04-14 at 06:42 PM.
#22
Senior Member
Join Date: Sep 2012
Location: 6367 km away from the center of the Earth
Posts: 1,666
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Those are my DIY mitts. Tested at -36C, 5hrs. They are an improved version of the Choko mitts. I don't know what their temperature limits is. But i have no doubt they are good at -40F.
The wool liners are Ortovox wool liners (pretty much like dachstein)
My gloves are also DIY from Choko. They have been tested at 0F which is their limit. Comfort is better at 5F or 10F. Without those modifications they are good up to 30F.
The wool liners are Ortovox wool liners (pretty much like dachstein)
My gloves are also DIY from Choko. They have been tested at 0F which is their limit. Comfort is better at 5F or 10F. Without those modifications they are good up to 30F.
Last edited by erig007; 11-04-14 at 08:33 PM.
Thread
Thread Starter
Forum
Replies
Last Post
chefisaac
Winter Cycling
3
12-18-12 12:00 PM
chefisaac
Clydesdales/Athenas (200+ lb / 91+ kg)
24
05-09-12 03:51 AM