Go Back  Bike Forums > Bike Forums > Cyclocross and Gravelbiking (Recreational)
Reload this Page >

Tektro CR720 - Spring tension not equal - INSTALL HELP NEEDED

Notices
Cyclocross and Gravelbiking (Recreational) This has to be the most physically intense sport ever invented. It's high speed bicycle racing on a short off road course or riding the off pavement rides on gravel like :The Dirty Kanza". We also have a dedicated Racing forum for the Cyclocross Hard Core Racers.

Tektro CR720 - Spring tension not equal - INSTALL HELP NEEDED

Old 11-06-13, 10:07 AM
  #1  
kmc143
Newbie
Thread Starter
 
Join Date: Oct 2010
Posts: 2
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Tektro CR720 - Spring tension not equal - INSTALL HELP NEEDED

Maybe someone encountered this issue before and found a remedy. I just purchased a set of Tektro CR720 brakes for a CX bike I'm building. When I tried to install the Tektro CR720 canti brakes on the front fork I noticed that the spring tension for each lever is not equal. Even if I set the spring tension adjuster on the right canti all the way in and the tension adjusted on the left all the way out, I cannot get an even tension on both springs.

I've attached photos of the cantis attached to a digital scale to show the amount of force (in ounce) to pull it parallel to the ground.

I've contacted Tektro and they advised to use different hole for the spring pin but the fork only have one hole for each brake post. Again, the spring tension adjuster is not much help either.

Did I get a pair with defective springs? Please help.
Attached Images
File Type: jpg
left_lever.jpg (50.7 KB, 35 views)
File Type: jpg
right_lever.jpg (54.0 KB, 32 views)
kmc143 is offline  
Old 11-06-13, 10:18 AM
  #2  
FrenchFit 
The Left Coast, USA
 
FrenchFit's Avatar
 
Join Date: Feb 2008
Posts: 3,757

Bikes: Bulls, Bianchi, Koga, Trek, Miyata

Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 360 Post(s)
Liked 20 Times in 13 Posts
This will qualify as a hack solution but I've changed spring tension by spreading it's rest position, or compacting the spring with vice grips. I have been surprised that it actually works, remains stable, ...if all else fails you could give this a try.
FrenchFit is offline  
Old 11-06-13, 12:02 PM
  #3  
fietsbob 
coprolite
 
fietsbob's Avatar
 
Join Date: Jun 2010
Location: NW,Oregon Coast
Posts: 41,897

Bikes: 8

Mentioned: 190 Post(s)
Tagged: 0 Thread(s)
Quoted: 7141 Post(s)
Liked 652 Times in 432 Posts
RTFM ? it's why 2 setscrews are there.

https://www.tektro.com/_english/03_su...load.php?fid=4

2, Take the pad turn it so it clears the fork/stay, weak side, back bend the spring further
was what we did before the MFG started putting those screws in..

3) the center cable can be off center to pull one side more than the other at first,

4) though 1 pad may hit the rim first , effective braking doesn't happen until both pads squeeze the rim.

so dont sweat it too much .. [untreated OCD? might need counseling.. ]

oh and 5) a thin washer behind 1 brake pad can make it closer.

Last edited by fietsbob; 11-06-13 at 12:06 PM.
fietsbob is offline  
Old 11-08-13, 07:58 AM
  #4  
kmc143
Newbie
Thread Starter
 
Join Date: Oct 2010
Posts: 2
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Thanks for all the suggestions. I did read the f*****g manual. It specifically stated to use tension adjuster screw to even out the tension.

I ended up spreading out the spring.
kmc143 is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
jargo432
Bicycle Mechanics
12
01-29-16 10:12 AM
lazybear
Bicycle Mechanics
8
01-02-16 10:18 AM
seajaye
Bicycle Mechanics
4
09-19-12 11:40 AM
southpawboston
Classic & Vintage
20
03-07-11 08:05 PM
QuickDraw
Classic & Vintage
1
03-02-10 05:10 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.