Can I "Y" a Lifpo4 and a SLA battery together
09-07-08, 05:45 PM
#1
Junior Member
Thread Starter
Join Date: Jul 2008
Posts: 14
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Can I "Y" a Lifpo4 and a SLA battery together
And charge them together?
I have two 36v 15ah batteries, and since they are the same voltage I was considering Ying them together and running them on my Shwinn Scooter.
Thanks in advance for replies.
I have two 36v 15ah batteries, and since they are the same voltage I was considering Ying them together and running them on my Shwinn Scooter.
Thanks in advance for replies.
09-07-08, 06:47 PM
#2
Banned.
Sure. Not to be a wiseass, but you "can" do anything, but it may be hard to assess the impact one may have on the other, in terms of charge/discharge cycles and overall life of each type of battery, being parallel and charged together.
One may suffer.
One may suffer.
09-07-08, 11:08 PM
#3
Junior Member
Join Date: Aug 2008
Posts: 16
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Did you check the voltage of the two battery packs with a volt meter when fully charged? I thing 24V Li batteries are typically 27 V.
You might want to isolate the two battery pack by putting a diode on each when you use them to power the bike. The current flow will then only run out, not in. That will keep one battery from charging the other while you are using them.
As for charging, I would definitely recommend doing them separately. The charging requirements are different for the two types of batteries, IIRC.
You might want to isolate the two battery pack by putting a diode on each when you use them to power the bike. The current flow will then only run out, not in. That will keep one battery from charging the other while you are using them.
As for charging, I would definitely recommend doing them separately. The charging requirements are different for the two types of batteries, IIRC.
09-08-08, 08:08 AM
#4
put our Heads Together
Join Date: Jun 2003
Location: southeast pennsylvania
Posts: 3,155
Bikes: a mountain bike with a cargo box on the back and aero bars on the front. an old well-worn dahon folding bike
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
With a diode, it's fine to connect them (make sure you connect in parallel not series!).
Don't try to charge em together.
It's possible to wire them together for discharging without a diode but its ONLY safe if the voltages are within something like 0.03 volts.
Don't try to charge em together.
It's possible to wire them together for discharging without a diode but its ONLY safe if the voltages are within something like 0.03 volts.
09-08-08, 05:13 PM
#5
Banned.
You might want to isolate the two battery pack by putting a diode on each when you use them to power the bike. The current flow will then only run out, not in. That will keep one battery from charging the other while you are using them.
As for charging, I would definitely recommend doing them separately. The charging requirements are different for the two types of batteries, IIRC.
As for charging, I would definitely recommend doing them separately. The charging requirements are different for the two types of batteries, IIRC.
Diodes are like one way valves for electricity. You would put one on each battery, anode to positive, or I'd put one on the pack with the lowest "resting" voltage, to feed it's current into the circuit when the overall voltage sags.
You'd also have to "size" the diode to what your controller/motor can pull in amps, probably 30amps or so. The diode could even run hot, so beware, or get one with a heatsink on it.
