700/23 versus 700/25
#1
Senior Member
Thread Starter
Join Date: Jul 2008
Posts: 618
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
700/23 versus 700/25
HI,
One of the local LBS has a sale on 700/25 kevlar lined tires for 9 bucks each, seems like a good deal, how much difference will the 25 width make for a road bikes performance and hardware usage ?
doug
One of the local LBS has a sale on 700/25 kevlar lined tires for 9 bucks each, seems like a good deal, how much difference will the 25 width make for a road bikes performance and hardware usage ?
doug
#2
Time for a change.
Join Date: Jan 2004
Location: 6 miles inland from the coast of Sussex, in the South East of England
Posts: 19,913
Bikes: Dale MT2000. Bianchi FS920 Kona Explosif. Giant TCR C. Boreas Ignis. Pinarello Fp Uno.
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 5 Times
in
4 Posts
Width isn't the only thing- What make of tyre and the type? Kevlar lined tyres at what weight and how hard are the casings and sidewall? Lots of things to affect tyre performance and life.
__________________
How long was I in the army? Five foot seven.
Spike Milligan
How long was I in the army? Five foot seven.
Spike Milligan
#3
Pretend Racer
Join Date: Mar 2007
Location: Northern Neck
Posts: 1,281
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
The 2mm difference is pretty much irrelevant performance wise. The other factors stapfam notes here are moreso. You'd be able to run them a few psi lower, of that's useful to you.
#4
Senior Member
Join Date: Mar 2009
Location: Oregon
Posts: 6,489
Mentioned: 31 Post(s)
Tagged: 0 Thread(s)
Quoted: 1182 Post(s)
Liked 833 Times
in
435 Posts
Hi, I suspect you will generate a wide range of opinions on this topic, so I'll start by giving you mine FWIW. Stapfam is correct; a lot of things affect tire performance besides width. I do have experience running 23's 25's and 28's all Continental ultra 2000 or 3000, as well as Ultra Gatorskins (28). All tires of the same width are not necessarily the same width, e.g., I put an older Continental 2000, 28 on my touring bike a few weeks ago and it is noticably narrower than the Conti Ultra Gatorskin 28 that it replaced.
I did not notice much difference between the 23's and the 25's as far as ride goes. The 25's are a little heavier so I'd expect acceleration and hill climbing to be affected some. I'm sure there was a slight difference, but I did not notice it, especially on the flat. These two tires are as close to " all things being equal" as you can get except wieght and width. The width of the 25mm might also cause some problems with brake clearance when removing the wheels.
I read somwhere (or I dreamed it) that the wider tire actually has less rolling resistance because there is less deformity and it maintains a rounder profile than the "skinny" tires. Maybe someone can either tell me I made it up or come up with a source for this theory.
I did not notice much difference between the 23's and the 25's as far as ride goes. The 25's are a little heavier so I'd expect acceleration and hill climbing to be affected some. I'm sure there was a slight difference, but I did not notice it, especially on the flat. These two tires are as close to " all things being equal" as you can get except wieght and width. The width of the 25mm might also cause some problems with brake clearance when removing the wheels.
I read somwhere (or I dreamed it) that the wider tire actually has less rolling resistance because there is less deformity and it maintains a rounder profile than the "skinny" tires. Maybe someone can either tell me I made it up or come up with a source for this theory.
#5
gone ride'n
Join Date: Aug 2007
Location: Upstate NY
Posts: 4,050
Bikes: Simoncini, Gary Fisher, Specialized Tarmac
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
$9 - go get'em! Even if you just keep one as a spare. If you have to have the very best you would not even be asking us, but if you are looking for value then you know what to do. At $9.00 even if they only last 1 season they owe you nothing at the end.
#6
Senior Member
Thread Starter
Join Date: Jul 2008
Posts: 618
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Forte" tires
hi,
I bought them at a local bike store that sells mostly specialized bike stuff. I was amazed how ignorant most of the employee's were about things in general hey I am newbie but they didn't seem to know their inventory either.
I asked for a 700/23 and they pointed me at folding tires. I asked if they had any other styles not sure.
I found the 700/25 next to the 700/28 and some 27inch (they still make them?)
the tire model had ( Forte 700/25 with kevlar belt) made in on of those middle east countries.
It said max pressure 125 and when I felt the belt with my thumb the tires felt pretty thick down the middle the dam bead felt like it may be wire.....
I hate wire beads......
IS there a secrete to gitting them off a wheel I broke 3 of those red pry bars with steel reinforced middles.. I finally figured out how to trap them on a spoke but the vittora beads are really tight...I read a cycling tip and they reccomend only removing the tire bead on one side and sliding the tube out and feeling for glass ouch and other debri inside the tire leaving one side on the rim,insert the new tube and then ever so carefully replace the bead with thumb pressure, I want to see someone do this with my steel rims on my ironman..
I swore several times today as I broke some of my tire tools and alot of cursing occured when I hooked up ye-old pump and the air went in out as fast thru the rip in the dang tube due to tire iron damages while trying to replace bead......
I took and oath to never buy another wire bead tire...
Doug
Help me resolve this cause one day I may have a flat on the open road 15 miles from home..PSPS those Vittora tires are new and rather pricy I hate to toss them new I put them on the Ironman and the Gatorskins on the CAD4
I bought them at a local bike store that sells mostly specialized bike stuff. I was amazed how ignorant most of the employee's were about things in general hey I am newbie but they didn't seem to know their inventory either.
I asked for a 700/23 and they pointed me at folding tires. I asked if they had any other styles not sure.
I found the 700/25 next to the 700/28 and some 27inch (they still make them?)
the tire model had ( Forte 700/25 with kevlar belt) made in on of those middle east countries.
It said max pressure 125 and when I felt the belt with my thumb the tires felt pretty thick down the middle the dam bead felt like it may be wire.....
I hate wire beads......
IS there a secrete to gitting them off a wheel I broke 3 of those red pry bars with steel reinforced middles.. I finally figured out how to trap them on a spoke but the vittora beads are really tight...I read a cycling tip and they reccomend only removing the tire bead on one side and sliding the tube out and feeling for glass ouch and other debri inside the tire leaving one side on the rim,insert the new tube and then ever so carefully replace the bead with thumb pressure, I want to see someone do this with my steel rims on my ironman..
I swore several times today as I broke some of my tire tools and alot of cursing occured when I hooked up ye-old pump and the air went in out as fast thru the rip in the dang tube due to tire iron damages while trying to replace bead......
I took and oath to never buy another wire bead tire...
Doug
Help me resolve this cause one day I may have a flat on the open road 15 miles from home..PSPS those Vittora tires are new and rather pricy I hate to toss them new I put them on the Ironman and the Gatorskins on the CAD4
Last edited by djnzlab1; 07-23-09 at 05:06 PM.
#7
Senior Member
Join Date: Jul 2009
Posts: 185
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
As for getting tires off the rim, I generally use just one plastic lever...it's all in the insertion and "slide" of the lever. You'll get the hang of it. Now, some tires take gorilla thumbs to get back on, but that's another story. Make sure your tube is seated inside the tire before inflating...if not, you'll hear a shotgun blast in your ear as you inflate and the "herniated" tube explodes!
Last edited by '47; 07-23-09 at 05:07 PM.
#9
Senior Member
Join Date: Nov 2008
Location: Bay Area, Calif.
Posts: 7,239
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 659 Post(s)
Likes: 0
Liked 7 Times
in
6 Posts
BTW, if you're not already doing so, it does help to first make sure that the tire beads are down as far in the rim well as possible all the way around with the obvious exception of the last little bit of the bead that you're still trying to get over the rim wall. It also helps to use the thinnest possible rim tape - that way the bead can sit a little lower in the rim well and give you just a bit more slack to get that last bit over the top. Finally it can help to provide a bit of lubrication in pushing the tire edge over the rim - a little soapy water can make it go much easier. Talc powder also helps and is easier to use on the road.
#10
Senior Member
Thread Starter
Join Date: Jul 2008
Posts: 618
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Thanks
Thanks for the info shouldl have thought of the soapy water..
Doug
Ive noticed most tubeless tires for crates they always use a lubricant to seat the rim.. duh..
Doug
Ive noticed most tubeless tires for crates they always use a lubricant to seat the rim.. duh..
#11
Senior Member
Join Date: Mar 2009
Location: Oregon
Posts: 6,489
Mentioned: 31 Post(s)
Tagged: 0 Thread(s)
Quoted: 1182 Post(s)
Liked 833 Times
in
435 Posts
Try starting across wheel from the stem and working both directions toward the stem. If you have to use a tire lever for the last little bit the stem seems to keep the tube away from the rim's edge and the tire lever. It also helps to "pinch" both sides of the tire as you work your way around. I think the idea here is not to let the bead to seat on the opposite side until both sides are mounted.
#12
feros ferio
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,798
Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;
Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1393 Post(s)
Liked 1,325 Times
in
837 Posts
You want a tight fit? Try Continental Ultra 2000s on Campagnolo Omega rims.
Speaking of tire dimensions, I have some 28mm Contis that are only about 25mm wide and actually clear the chainstays on my Bianchi. I could never have put 28mm Specialized Armadillos on that bike.
Speaking of tire dimensions, I have some 28mm Contis that are only about 25mm wide and actually clear the chainstays on my Bianchi. I could never have put 28mm Specialized Armadillos on that bike.
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
#13
just keep riding
Join Date: Feb 2005
Location: Milledgeville, Georgia
Posts: 13,560
Bikes: 2018 Black Mountain Cycles MCD,2017 Advocate Cycles Seldom Seen Drop Bar, 2017 Niner Jet 9 Alloy, 2015 Zukas custom road, 2003 KHS Milano Tandem, 1986 Nishiki Cadence rigid MTB, 1980ish Fuji S-12S
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 173 Post(s)
Liked 33 Times
in
22 Posts
Certain tire and rim combinations tend to be very tight. Some tires have a larger or smaller diameter. Same thing for rims. I have not found wire bead tires to be any tighter as a rule than those with kevlar beads.
#15
dolce far niente
Join Date: Apr 2009
Location: Annapolis, MD
Posts: 230
Bikes: Cannondale Synapse Carbon, Dura Ace
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I too am intersted in the difference. Currently riding Michelin Orium 23's and thinking of switching to Gatorskin 25's. Mostly due to my weight of 250lbs. The 23's have been no problem though
Thread opinions range from 'no difference' to 'superior ride'. Any more experiences?
Thread opinions range from 'no difference' to 'superior ride'. Any more experiences?
#16
Time for a change.
Join Date: Jan 2004
Location: 6 miles inland from the coast of Sussex, in the South East of England
Posts: 19,913
Bikes: Dale MT2000. Bianchi FS920 Kona Explosif. Giant TCR C. Boreas Ignis. Pinarello Fp Uno.
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 5 Times
in
4 Posts
BTW, if you're not already doing so, it does help to first make sure that the tire beads are down as far in the rim well as possible all the way around with the obvious exception of the last little bit of the bead that you're still trying to get over the rim wall. It also helps to use the thinnest possible rim tape - that way the bead can sit a little lower in the rim well and give you just a bit more slack to get that last bit over the top. Finally it can help to provide a bit of lubrication in pushing the tire edge over the rim - a little soapy water can make it go much easier. Talc powder also helps and is easier to use on the road.
Getting off is a reverse of fitting but realy push the bead away from the rim all the way round and into the well of the rim. Then struggle.
You will find that a tyre that has been used will fit and come off easier- But I do have a couple of wheels that I dread getting a puncture with. Tight rims and tight tyres do not mix.
And on the tyre width- I only use 23's so no idea if any others will be faster or more comfy. Only thing that varies is the presure. 120 on Boreas- 105 on the TCR- and 100 f and 120 r on the FCR. And all are Michelin PR 2's.
__________________
How long was I in the army? Five foot seven.
Spike Milligan
How long was I in the army? Five foot seven.
Spike Milligan
Last edited by stapfam; 07-24-09 at 01:14 PM.
#17
Senior Member
Thread Starter
Join Date: Jul 2008
Posts: 618
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Soapy water works
HI,
thanks for the help I mixed up a spray bottle of that dawn dish washing soap some water and sprayed the tube and the bead adna little in the tire, was able to push the bead over the rim 100% without tools. It was tight but the lubricant made it possiable.
When I added air some of the soapy bubbles came out as the rim and bead found their place.
I deflated the tire a little to check the bead/tube for any pinching didn't find any pushed the pressure to 110 and have checked the tire every so many hour to be sure it wasn't delflating..
SO it be good the ironman bike hits the road. I ride it mostly on wet days it seems to hold the road better and it washes off easily .
thanks again.
Doug
thanks for the help I mixed up a spray bottle of that dawn dish washing soap some water and sprayed the tube and the bead adna little in the tire, was able to push the bead over the rim 100% without tools. It was tight but the lubricant made it possiable.
When I added air some of the soapy bubbles came out as the rim and bead found their place.
I deflated the tire a little to check the bead/tube for any pinching didn't find any pushed the pressure to 110 and have checked the tire every so many hour to be sure it wasn't delflating..
SO it be good the ironman bike hits the road. I ride it mostly on wet days it seems to hold the road better and it washes off easily .
thanks again.
Doug
#18
Senior Member
Join Date: Jun 2007
Location: Maumelle, AR
Posts: 1,075
Bikes: 2012 Scorpion FX trike, 2016 Catrike 700
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 93 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I ride wire bead tires. 23 on the front and 25 on the back. Did this by accident because I picked up the wrong tire at the LBS. Did not want to drive back when I started mounting the tires. I get the better ride of the 25 on the back since I can run a lower pressure. I think I will stick with this accident.
#20
Clipless faller
Join Date: Sep 2007
Location: Austin, TX
Posts: 268
Bikes: 2008 Specialized Allez Elite Compact, 1981 Raleigh Super Record 10-sp, Trek 4900 MTB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I switched from 23s to Kevlar-belted 25s in February. They've been great. No dropoff in performance. However, they might not be true 25s, because when I manually measure their circumference, they're 2096 mm, the same as 23s.
#21
Lance Legweak
My mechanic at the LBS suggested I go with 23's up front. I forget all the differences he said, but I do remember him saying the ride quality would probably go down with 23's, but not much. 25's can be run on the rear, or for $9, you have a rear for the stationary trainer.
#22
dolce far niente
Join Date: Apr 2009
Location: Annapolis, MD
Posts: 230
Bikes: Cannondale Synapse Carbon, Dura Ace
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#23
Clipless faller
Join Date: Sep 2007
Location: Austin, TX
Posts: 268
Bikes: 2008 Specialized Allez Elite Compact, 1981 Raleigh Super Record 10-sp, Trek 4900 MTB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Hutchinson Top Speed ProTech Kevlar (whew!). Mail order from Nashbar for $14.99 each.