Go Back  Bike Forums > Bike Forums > Folding Bikes
Reload this Page >

Problem with securing seat

Notices
Folding Bikes Discuss the unique features and issues of folding bikes. Also a great place to learn what folding bike will work best for your needs.

Problem with securing seat

Old 03-01-21, 12:02 PM
  #1  
Ajay423
Junior Member
Thread Starter
 
Join Date: Mar 2021
Location: Savannah
Posts: 5

Bikes: Dahon boardwalk 7, soma

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Problem with securing seat

I just acquired a forest green Dahon Boardwalk 7 speed with Shimano r derailleur.
The sear tube has a plastic shim and the tube top has a welded/brazed collar with (two) arms with holes at each rear side. It also has a Quick Release cam skewer to clamp the seatpost to secure the seat in position. The seatpost says “34” on the lower part.
I am unable to make this work. Even tightened to the point where both arms begin to touch, the seat slips. I used tools to tighten further, stripped the plastic(?) threads in the skewer knurled knob.
Does thus bike require a different shim? Different clamp? Different something else? The seat post fits snuggly into the loosened seatpost/shim - just can’t tighten it to non slip.
Thanks, in advance for any help. I can’t post pictures yet since I am a newbie.
Ajay423 is offline  
Old 03-01-21, 01:02 PM
  #2  
linberl
Senior Member
 
linberl's Avatar
 
Join Date: Jun 2014
Location: SF Bay Area
Posts: 3,077

Bikes: 2017 Bike Friday PakiT. Dahon Mu Uno (trailer bike) Sold: 2003 Bike Friday NWT, 1997 Trek 720, 1993 Trek 520)

Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 1193 Post(s)
Liked 181 Times in 152 Posts
You can try carbon paste, but you may need to buy a better qualify clamp that has a deep hex fitting so you can leverage it tight. I did. Chromag clamp worked wonders for me.
linberl is offline  
Old 03-01-21, 05:38 PM
  #3  
tcs
Palmer
 
tcs's Avatar
 
Join Date: Mar 2007
Location: Parts Unknown
Posts: 6,600

Bikes: 1980 Mike Melton, 1982 Stumpjumper, 1982 Santana, 1984 Alex Moulton AM, 2008 BikeFriday tikit T-♾, 2010 Dawes Briercliffe, 2017 Dahon Curl i8, 2019 Surly ˝DT14, 2021 Motobecane Turino 1x12

Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
Quoted: 846 Post(s)
Liked 379 Times in 245 Posts
The most common solution to this problem is to clean the seatpost and tightening collar. Like, really, really clean.
tcs is offline  
Old 03-04-21, 11:18 AM
  #4  
Inisfallen
Senior Member
 
Inisfallen's Avatar
 
Join Date: Jun 2014
Posts: 66
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 31 Post(s)
Liked 28 Times in 14 Posts
I had a problem with my seatpost slipping down a while back. Different bike, but same problem.

Someone here suggested that I sand the seatpost a bit where it's clamped with rough (not fine) sandpaper.

It worked. It's worth a try, I guess. Obviously, there's a limit on how many times you can do that, but it's held pretty well for a long time for me.
Inisfallen is offline  
Old 03-05-21, 05:32 AM
  #5  
Geepig
Senior Member
 
Geepig's Avatar
 
Join Date: Sep 2020
Location: Eastern Poland
Posts: 708

Bikes: Romet Jubilat x 4, Wigry x 1, Turing x 1

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 185 Post(s)
Liked 180 Times in 137 Posts
Once it is sanded then it should not need doing again, unless one is in the habit of adjusting the saddle often enough for wear to occur. The folders I fold usually have the saddle really low so that I don't touch it.
Geepig is offline  
Old 03-05-21, 08:54 PM
  #6  
3speedslow
Senior Member
 
3speedslow's Avatar
 
Join Date: Oct 2010
Location: Jacksonville, NC
Posts: 8,913

Bikes: A few

Mentioned: 114 Post(s)
Tagged: 0 Thread(s)
Quoted: 1803 Post(s)
Liked 683 Times in 441 Posts
Plastic wears out. Dahon USA sells replacements.
3speedslow is offline  
Old 03-06-21, 06:13 AM
  #7  
Tourist in MSN
Senior Member
 
Join Date: Aug 2010
Location: Madison, WI
Posts: 8,448

Bikes: 1961 Ideor, 1966 Perfekt 3 Speed AB Hub, 1994 Bridgestone MB-6, 2006 Airnimal Joey, 2009 Thorn Sherpa, 2013 Thorn Nomad MkII, 2015 VO Pass Hunter, 2017 Lynskey Backroad, 2017 Raleigh Gran Prix, 1980s Bianchi Mixte on a trainer. Others are now gone.

Mentioned: 38 Post(s)
Tagged: 0 Thread(s)
Quoted: 2337 Post(s)
Likes: 0
Liked 582 Times in 478 Posts
I have a seatpost on a different bike, I think it is slightly undersized, but just barely. It is painted black. I sprayed on a couple more layers of back paint, let it harden up for a week before re-installing. That was enough to get the size up to where it should be, no longer slips.

But in your case where you say that two arms touch, that does not sound good. Is it possible that the seatpost has been changed to a different size?

I do not have a Dahon, so consider my comments as generic, not specific to your bike.
Tourist in MSN is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.