Removing a Nexus 8 wheel from a Swift
#1
Senior Member
Thread Starter
Join Date: Nov 2004
Location: Smyrna, GA
Posts: 217
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Removing a Nexus 8 wheel from a Swift
Folded and packed my BF NWT (for the first time) last night in preparation for a trip. My GF is using a Nexus 8 equipped Swift. Not sure how to disconnect the shifter cable, and after that...the chain seems really tight and the dropouts are horizontal. Do you derail the chain off the front, or off the back? Assuming I can get enough slack. Trying to pack the Swift into the same size case (Samsonite F'Lite 31") as the BF. I wish I (we) had two BF's!
#2
Part-time epistemologist
Hey Zonker,
I don't have a Swift, but typically there is enough space in the horizontal dropouts to slide the wheel far enough forward to slip the chain off. Sometimes you can tilt the wheel within the dropouts as well to get a little more space. Alternatively, if you are desperate, you can take off the chainring.
Then again, I have only one internal hub bike in recent history without a chain tensioner.
-G
I don't have a Swift, but typically there is enough space in the horizontal dropouts to slide the wheel far enough forward to slip the chain off. Sometimes you can tilt the wheel within the dropouts as well to get a little more space. Alternatively, if you are desperate, you can take off the chainring.
Then again, I have only one internal hub bike in recent history without a chain tensioner.
-G
__________________
A narrative on bicycle driving.
A narrative on bicycle driving.
#3
too many bikes
Join Date: Feb 2006
Location: Hawaii
Posts: 662
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Something's wrong. You don't have to disconnect any cables to pack a Swift.
Use a master link in your chain and take the chain off.... optional, though, it will pack with the chain on.
Use a master link in your chain and take the chain off.... optional, though, it will pack with the chain on.
#4
Senior Member
Thread Starter
Join Date: Nov 2004
Location: Smyrna, GA
Posts: 217
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I've got tonight and tomorrow night to figure it out!
#5
Full Member
Check out the Sheldon Brown / Harris Cycle link for a copy of the service manual at
https://sheldonbrown.com/nexus8/ for help on how to disconnect the cable. I have the SA-8 hubs and they are easy to remove once you understand how. I would bet the Shimano hubs are easy once you figure out the tricks. Just remember to be very careful with the shifter cable once removed. I trashed my cable on my wife's DT 8H while practicing putting it into a suitcase by carelessly bending it. I felt really stupid after that, and then I had to replace it before the bike would be able to be used again.
I recommend carrying space brake/shifter cables on any trip. Spare tubes and brake pads and other parts are also nice to have if you are going to be in more remote areas. Don't forget to bring the tools needed to assemble and disassemble the bike once you get to where you are going. I had a heck of a time getting a decent adjustable wrench in Bali when I needed one...
Good luck on your trip!
#6
Senior Member
Thread Starter
Join Date: Nov 2004
Location: Smyrna, GA
Posts: 217
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
The easiest way to get the chain off a hub-gear bike with horizontal dropouts is to loosen the hub nuts, push the wheel forward slightly (it should still be able to turn), and then rotate the cranks with one hand while derailling the chain by pushing sideways on it while you turn the crank. Much easier to get it off the front chainring rather than the rear cog.
Check out the Sheldon Brown / Harris Cycle link for a copy of the service manual at
https://sheldonbrown.com/nexus8/ for help on how to disconnect the cable. I have the SA-8 hubs and they are easy to remove once you understand how. I would bet the Shimano hubs are easy once you figure out the tricks. Just remember to be very careful with the shifter cable once removed. I trashed my cable on my wife's DT 8H while practicing putting it into a suitcase by carelessly bending it. I felt really stupid after that, and then I had to replace it before the bike would be able to be used again.
I recommend carrying space brake/shifter cables on any trip. Spare tubes and brake pads and other parts are also nice to have if you are going to be in more remote areas. Don't forget to bring the tools needed to assemble and disassemble the bike once you get to where you are going. I had a heck of a time getting a decent adjustable wrench in Bali when I needed one...
Good luck on your trip!
Check out the Sheldon Brown / Harris Cycle link for a copy of the service manual at
https://sheldonbrown.com/nexus8/ for help on how to disconnect the cable. I have the SA-8 hubs and they are easy to remove once you understand how. I would bet the Shimano hubs are easy once you figure out the tricks. Just remember to be very careful with the shifter cable once removed. I trashed my cable on my wife's DT 8H while practicing putting it into a suitcase by carelessly bending it. I felt really stupid after that, and then I had to replace it before the bike would be able to be used again.
I recommend carrying space brake/shifter cables on any trip. Spare tubes and brake pads and other parts are also nice to have if you are going to be in more remote areas. Don't forget to bring the tools needed to assemble and disassemble the bike once you get to where you are going. I had a heck of a time getting a decent adjustable wrench in Bali when I needed one...
Good luck on your trip!
#7
Full Member
Sorry my timing was off, but it sounds like you had a good trip. Any pictures or lessons learned while traveling?