Go Back  Bike Forums > Bike Forums > Framebuilders
Reload this Page >

filing down tig welds on steel frames?

Notices
Framebuilders Thinking about a custom frame? Lugged vs Fillet Brazed. Different Frame materials? Newvex or Pacenti Lugs? why get a custom Road, Mountain, or Track Frame? Got a question about framebuilding? Lets discuss framebuilding at it's finest.

filing down tig welds on steel frames?

Old 07-23-07, 02:42 PM
  #1  
anti-sheep
Thread Starter
 
astrx's Avatar
 
Join Date: May 2005
Location: pittsburgh
Posts: 313

Bikes: generic lugged track frame

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
filing down tig welds on steel frames?

after having my frame severely dented by an attempted theft, i have decided to have two bikes, one for the real rides and one for a commuter/around town bike. the around towner is gonna have to be cheap, and because of my own personal preferences i dont want a lugged bike. so the question:

can you file down tig welds on steel frames for a more filet brazed look? I am specifically talking about a 99ish khs aero track made with reynolds 520.
astrx is offline  
Old 07-23-07, 03:25 PM
  #2  
Ho-Jahm
 
Hocam's Avatar
 
Join Date: Nov 2006
Location: Manchester, NH
Posts: 4,228
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 5 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I think a bondo covering would be safer, easier and look better.
Hocam is offline  
Old 07-23-07, 03:34 PM
  #3  
Grumbly Goat
 
Bushman's Avatar
 
Join Date: Jul 2007
Posts: 895

Bikes: bicycles with round wheels

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by Hocam
I think a bondo covering would be safer, easier and look better.
+1! yes! break out the bondo, mix it properly and apply it. Then spend a few hours carefully shaping it and feather it into the existing paint a bit (sand it). Work you way up about 1000 grit wet dry, and start wet sanding, rinsing the paper lots. then dry with ACETONE, primer it and paint it.

prep prep prep is key here.
Bushman is offline  
Old 07-23-07, 04:32 PM
  #4  
Banned
 
Join Date: Aug 2005
Posts: 5,115
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times in 1 Post
You can do the same thing with 5 minute epoxy, and since it's is an adhesive it will stick better to the mishmash of stuff that is likely to be there to bond to. You may need to add some filler to it, talc powder microballoons sadust that was screened or run through a blender. In theory one shouldn't file/grind a weld.
NoReg is offline  
Old 07-23-07, 09:22 PM
  #5  
Senior Member
 
Join Date: Dec 2004
Location: Athens, Ohio
Posts: 5,104

Bikes: Custom Custom Custom

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Sorry to slightly steal the thread but can anyone recommend a powder coat safe/friendly (as in won't burn up or deform in the curing process) filler material?
nitropowered is offline  
Old 07-24-07, 01:29 PM
  #6  
Senior Member
 
Nessism's Avatar
 
Join Date: Jun 2004
Location: Torrance, CA
Posts: 3,059

Bikes: Homebuilt steel

Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 2156 Post(s)
Liked 416 Times in 330 Posts
Originally Posted by astrx
can you file down tig welds on steel frames for a more filet brazed look? I am specifically talking about a 99ish khs aero track made with reynolds 520.

You can file them but don't go too deep - just knock off the ugly high-spot lumps. I did this on a frame and it turned out great.
Nessism is offline  
Old 07-26-07, 01:58 PM
  #7  
Banned
 
Join Date: Aug 2005
Posts: 5,115
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times in 1 Post
There is a "bondo" you can powdercoat over. Maybe Eastwood has it. I forget the name, but I think I may have dropped it here before it. It would be worth asking your coater, because there are different levels of sophistication out there. Andrews, for instance says on their page there are PCs in the works that will coat plain plastic, or wood. Other powdercoaters specify you have to finish with (usually tigged) bronze. If there isn't metal content then it is hard to get coverage with electrostatics, but some seem more confident about the options than others.
NoReg is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.