Go Back  Bike Forums > Bike Forums > Framebuilders
Reload this Page >

Ugh... Lesson learned

Notices
Framebuilders Thinking about a custom frame? Lugged vs Fillet Brazed. Different Frame materials? Newvex or Pacenti Lugs? why get a custom Road, Mountain, or Track Frame? Got a question about framebuilding? Lets discuss framebuilding at it's finest.

Ugh... Lesson learned

Old 02-27-14, 10:13 AM
  #1  
Member
Thread Starter
 
Join Date: Feb 2014
Location: Sacramento, CA
Posts: 46

Bikes: 1996 Gary Fisher Joshua X1 MTB; Micargi beach cruiser, Marfik FG

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Ugh... Lesson learned

I've always had a passion for bike frames and I have a long history of metal work and fabrication. I *thought* I knew what I was doing BEFORE I did research on bike frames and particularly lugged frames. I think I can still pull it off and make the best of this but here you have it, I'm opening myself up to ridicule, laughter, insults, all the rest.

I'm the last person to brag on myself, but I can really stack some dimes with my welder. Brazing is definitely something I need a LOT more practice with and I must move to silver solder.

Attached Images
File Type: jpg
20140227_053855.jpg (40.2 KB, 194 views)
Fiveflat is offline  
Old 02-27-14, 04:50 PM
  #2  
Team Beer
 
Cynikal's Avatar
 
Join Date: Apr 2004
Location: Sacramento CA
Posts: 6,338

Bikes: Too Many

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 113 Post(s)
Liked 157 Times in 103 Posts
Not a bad start. Have you brazed before? I would start with tight fitting tubes so you can cut them up to verify penetration. I’m just starting to learn brazing myself and I’m local to you. Let me know if you want to connect and chat bike/welding stuff.
__________________
I'm not one for fawning over bicycles, but I do believe that our bikes communicate with us, and what this bike is saying is, "You're an idiot." BikeSnobNYC
Cynikal is offline  
Old 02-27-14, 05:53 PM
  #3  
Randomhead
 
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,364
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,664 Times in 2,497 Posts
So that's bronze?
the bb shell has the advantage that you can tell if you got penetration by looking inside. What does it look like in there? Unfortunately, it looks like there wasn't quite enough heat to get good penetration. OTOH, it's not burned to a crisp, although you overheated a spot up the seat tube a little.

I'm always a little surprised that people don't practice on pieces of tubing. When I'm doing something new I practice with tubing and I've been brazing since the mid-'70s. .058 inch wall tubing is a decent slip fit over the next 1/8" smaller diameter tubing. So much cheaper than parts.
unterhausen is offline  
Old 02-27-14, 06:15 PM
  #4  
Old fart
 
JohnDThompson's Avatar
 
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,936

Bikes: Several, mostly not name brands.

Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3571 Post(s)
Liked 3,367 Times in 1,916 Posts
The build up of brass on the tubes suggests that you didn't heat the shell enough before starting to add the brass. The thin tubing heats much faster than the thick shell, so the brass will tend to pool out on the tube before going into the joint. Keep the flame on the shell until it's fully hot before hitting the flame on the tube. That way when the brass melts, it gets pulled into the joint right away without so much pooling. This was right after washing off the flux, before any finishing:

JohnDThompson is offline  
Old 02-27-14, 08:56 PM
  #5  
Senior Member
 
Andrew R Stewart's Avatar
 
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,003

Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4172 Post(s)
Liked 3,792 Times in 2,271 Posts
I'd suggest that you consider getting more comfy with bronze before trying silver. Why? because you need to get better with something, bronze is FAR lower cost, it's stronger if the gaps are large of the joint is less then well cleaned, You'll want to use it for some joints even if you are silvering all that you can and more reasons. I find it harder to flow braze with brass because of the higher temp, when i go to silver there still is a remembering curve but less then th other way around IME. I second Eric's advice of tube sleeves as practice. i have 4 cut and ready for prepping in a box I'm taking to a friend for when i help him paint my recent frame. He's also going to give me a brazing tune up. Andy.
Andrew R Stewart is offline  
Old 02-28-14, 09:34 AM
  #6  
Member
Thread Starter
 
Join Date: Feb 2014
Location: Sacramento, CA
Posts: 46

Bikes: 1996 Gary Fisher Joshua X1 MTB; Micargi beach cruiser, Marfik FG

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by Cynikal
Not a bad start. Have you brazed before? I would start with tight fitting tubes so you can cut them up to verify penetration. I’m just starting to learn brazing myself and I’m local to you. Let me know if you want to connect and chat bike/welding stuff.
Yea, that would work. I'm actually a little south of Sac but not far. Always got a good selection of cheap beer in my shop fridge too
Fiveflat is offline  
Old 02-28-14, 09:38 AM
  #7  
Member
Thread Starter
 
Join Date: Feb 2014
Location: Sacramento, CA
Posts: 46

Bikes: 1996 Gary Fisher Joshua X1 MTB; Micargi beach cruiser, Marfik FG

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by JohnDThompson
The build up of brass on the tubes suggests that you didn't heat the shell enough before starting to add the brass.
Exactly, I figured this out by now. I think I'll have much better luck with the rest of the joints. I did get good penetration into the shell of the BB but it's just not the prettiest from the outside.



Thanks for all the constructive criticism from everyone, rather than bashing. I appreciate the help and will try to apply all the suggestions here!
Fiveflat is offline  
Old 02-28-14, 12:54 PM
  #8  
Randomhead
 
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,364
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,664 Times in 2,497 Posts
I always used silver for lugs, and the fact that I hadn't used brass grated on my nerves a little. The first lug I did with brass, I didn't get full penetration and the filler refused to budge for me after a while. So I cut up some tubes and practiced on them. I made sleeves of 1/2", 1", 1.5" and 3". The smaller ones went fine, but with the bigger sleeves what I found was that my torch wasn't supplying enough heat. After a few tries, I could flow brass through a 3" sleeve, but it was all I could do to keep it hot enough to make that work. That exercise was really useful to me. I got the biggest tip my tanks can handle and it went a lot easier.
unterhausen is offline  
Old 03-09-14, 01:35 AM
  #9  
Senior Member
 
Join Date: Oct 2011
Location: SF Bay Area
Posts: 428

Bikes: 2003 Lemond Zurich; 1987 Schwinn Tempo; 1968 PX10; 1978 PX10LE, Peugeot Course; A-D Vent Noir

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Originally Posted by unterhausen
I always used silver for lugs, and the fact that I hadn't used brass grated on my nerves a little. The first lug I did with brass, I didn't get full penetration and the filler refused to budge for me after a while. So I cut up some tubes and practiced on them. I made sleeves of 1/2", 1", 1.5" and 3". The smaller ones went fine, but with the bigger sleeves what I found was that my torch wasn't supplying enough heat. After a few tries, I could flow brass through a 3" sleeve, but it was all I could do to keep it hot enough to make that work. That exercise was really useful to me. I got the biggest tip my tanks can handle and it went a lot easier.
FWIW I also prefer silver to brass for lugs and for any sleeved joint that is relatively tight-fitting, because silver rod: 1) melts at a lower temperature;
and, 2) is more easily drawn by capillary action into the joint. Brass may be stronger for looser fitting joints.
neurocop is offline  
Old 03-10-14, 04:49 PM
  #10  
Randomhead
 
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,364
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,664 Times in 2,497 Posts
I thought it was interesting that the people that learned on brass said it was easier than silver. Now that I have a properly sized torch tip, I am not sure I agree, but there isn't much difference.
unterhausen is offline  
Old 03-11-14, 10:17 AM
  #11  
tuz
Senior Member
 
Join Date: Dec 2006
Location: Toronto/Montréal
Posts: 1,209

Bikes: Eight homemade, three very dusty

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 10 Post(s)
Liked 12 Times in 7 Posts
My experience is that brass flows quite well in lugs with the right amount of heat. I like that the flux is quite tolerant so you can blast the joint and braze rapidly. 55+ % silver does flow very quickly but you have to be a bit more gentle with the flux. 50% (and under) flows more like brass.
tuz is offline  
Old 03-11-14, 02:18 PM
  #12  
Banned
 
Join Date: Jun 2010
Location: NW,Oregon Coast
Posts: 43,598

Bikes: 8

Mentioned: 197 Post(s)
Tagged: 0 Thread(s)
Quoted: 7607 Post(s)
Liked 1,354 Times in 861 Posts
kind of a +1 ... heavier castings like fork crowns and bb shells
focus on heating them first and the tubes will likely be hot enough .

playing the flame on them later and little ..

another + on tight fits .. silver wont fill the gaps that brass will .
fietsbob is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
chased
Framebuilders
6
08-01-16 03:52 PM
TickTockToe
Framebuilders
77
02-23-13 12:32 AM
triathloner
Framebuilders
5
02-01-12 09:56 PM
Ferrite
Framebuilders
10
04-12-10 08:58 AM
painthawg
Framebuilders
5
01-06-10 02:52 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.