Properly using quick release?
#1
Senior Member
Thread Starter
Join Date: Jul 2006
Location: Walnut Creek, CA
Posts: 72
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Properly using quick release?
My mid 70's road bike has quick release front wheel...Im not sure how one is supposed to use it? Me, I tighten it just enough to I can flip the thing over with effort, if i tighten it anymore its impossible to flip it over.
#2
Senior Member
Join Date: May 2005
Location: Queanbeyan, Australia.
Posts: 4,135
Mentioned: 85 Post(s)
Tagged: 0 Thread(s)
Quoted: 3450 Post(s)
Liked 420 Times
in
289 Posts
Quick release levers don't have to be set too tight.
The rule of thumb that I've learn't is that they should be adjusted so that the lever is parralel with the axle with NO effort. Then you close them. You may be damaging the mechanisim if they're set too tight.
Regards, Anthony
The rule of thumb that I've learn't is that they should be adjusted so that the lever is parralel with the axle with NO effort. Then you close them. You may be damaging the mechanisim if they're set too tight.
Regards, Anthony
#4
Senior Member
Join Date: Jun 2006
Location: Cardiff, Wales
Posts: 164
Bikes: Apollo CX10
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
er... mine has a ratchet, so does my mates, so I assume that they all come with a ratchet.
you leave the lever open, tighten the nut until you start hearing clicking, give it a turn for luck. then close the lever.
Voila! secured.
you leave the lever open, tighten the nut until you start hearing clicking, give it a turn for luck. then close the lever.
Voila! secured.
#5
Senior Member
Join Date: Dec 2003
Location: Richmond, VA
Posts: 613
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
The lever should start resisting movement at 90 degrees to the fork legs. Adjust the acorn nut on the other side accordingly.
https://www.bicyclinglife.com/HowTo/UseAQuickRelease.htm
https://www.bicyclinglife.com/HowTo/UseAQuickRelease.htm
Last edited by gwhunt23; 08-31-06 at 08:22 PM.
#6
You need a new bike
Join Date: Aug 2002
Posts: 5,433
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 4 Times
in
3 Posts
If you still are unsure how to use the quick release, any bike shop will be happy to show you. Losing a front wheel while riding will just ruin your whole afternoon. And a 70's bike probably doesn't have lawyer lips to save you if your front wheel is too loose.
#7
Senior Member
Join Date: Sep 2002
Location: Philadelphia suburb
Posts: 911
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Turn the nut on the other side to remove or tighten the wheel, and just open and close the quick release lever itself. The old cliche is that the lever should be tight enough to leave an imprint on your palm when you close it.
If you don't know about him, the widely- and well-respected Sheldon Brown usually has an informative, helpful discussion of just about any cycling-related topic you could imagine. Here's what he has to say about quick-release levers: https://www.sheldonbrown.com/flats.html#quickrelease.
If you don't know about him, the widely- and well-respected Sheldon Brown usually has an informative, helpful discussion of just about any cycling-related topic you could imagine. Here's what he has to say about quick-release levers: https://www.sheldonbrown.com/flats.html#quickrelease.
Last edited by lrzipris; 09-05-06 at 05:30 AM.
#8
Senior Member
Join Date: Jun 2006
Location: Livonia, MI
Posts: 873
Bikes: Pacific Duece AL with mods
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Originally Posted by lrzipris
Turn the nut on the other side to remove or tighten the wheel, and just open and close the quick release lever itself. The old cliche is that the lever should be tight enough to leave an imprint on your palm when you close it.
If you donn;t know about him, the widely- and well-respected Sheldon Brown usually has an informative, helpful discussion of just about any cycling-related topic you could imagine. Here's what he has to say about quick-release levers: https://www.sheldonbrown.com/flats.html#quickrelease.
If you donn;t know about him, the widely- and well-respected Sheldon Brown usually has an informative, helpful discussion of just about any cycling-related topic you could imagine. Here's what he has to say about quick-release levers: https://www.sheldonbrown.com/flats.html#quickrelease.
#9
Senior Member
Join Date: Sep 2003
Location: Willimantic, Connecticut
Posts: 499
Bikes: '70s Puch sport tourer, '90 Peugeot Success.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Sheldon omits a third option - i forget the maker, i'm sure someone else here knows - i use a Ti skewer that tightens with an Allen wrench. I never liked having to worry about QRs, either in terms of their possibly loosening, or the added hassle of having to lock up the wheels or risk theft.