using tuning stand
#1
Junior Member
Thread Starter
Join Date: May 2013
Location: Indiana
Posts: 8
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
using tuning stand
When doing your back wheel of your bike does it mater what side you have the freewheel on when its on the tuning stand? Or should you remove the freewheel then put it on the stand?
#2
Senior Member
Join Date: Oct 2008
Location: Northern NY...Brownville
Posts: 2,571
Bikes: Specialized Aethos, Specialized Diverge Comp E5
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 241 Post(s)
Liked 453 Times
in
264 Posts
Tuning? or Truing stand? I'll bet truing stand. I've always left the freewheel/cassette on the wheel unless removing it for service/cleaning, etc.
#3
Senior Member
Join Date: Dec 2010
Posts: 8,951
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 14 Post(s)
Likes: 0
Liked 13 Times
in
12 Posts
Perhaps if you're judging tension by pitch, tuning stand might be appropriate? In any case, it doesn't matter if the cassette is on the wheel or which side it is on, though I always put it on the right so it's easier to keep straight in my head. You can flip sides to check dish.
#4
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,784
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3587 Post(s)
Liked 3,400 Times
in
1,934 Posts
It shouldn't matter. Use a dishing gauge to ensure that the rim is centered between the hub locknuts. This is important even with self-centering stands, as they easily go out of adjustment.
#5
Senior Member
Join Date: Oct 2008
Location: Northern NY...Brownville
Posts: 2,571
Bikes: Specialized Aethos, Specialized Diverge Comp E5
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 241 Post(s)
Liked 453 Times
in
264 Posts
I've reread the post several times after my reply and honestly make no sense out of it but it was fun to read.
Yeah I use a dish tool but guess this person is talking more about checking the "trueness" of the wheel and is new to it.
Just be sure to check the tension of all the spokes before starting any truing project...if not done correctly you can wind up really messing up.
If you're not sure do a search on google. I'll bet there are quite a few videos on wheel truing on a bike, stand, etc.
Yeah I use a dish tool but guess this person is talking more about checking the "trueness" of the wheel and is new to it.
Just be sure to check the tension of all the spokes before starting any truing project...if not done correctly you can wind up really messing up.
If you're not sure do a search on google. I'll bet there are quite a few videos on wheel truing on a bike, stand, etc.
#6
Senior Member
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,900
Bikes: Fuji Touring, Novara Randonee
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2603 Post(s)
Liked 1,925 Times
in
1,208 Posts
For a truing stand, it doesn't matter which side it's on. It does matter that the rim should be at the same location left-right when you flip it over -- then you'll have the dish right.
#7
Banned
Im +1 with JDT, own a Dish Stick with your truing stand. touch points are the axle lock nuts and the rim sides,
it is to compare the symmetry to B = .
it is to compare the symmetry to B = .