grip removal
#1
Shreddin' heaven on his 20"
Thread Starter
Join Date: May 2005
Location: markham, ontario, canada aka chinatown north
Posts: 1,151
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
grip removal
anyone have any idea how to take of friggin grips? they're pissing me off.... i'm triyng to put on shifters but NOOOOOOOOOOOOOOOOo they wont come off. i'm contemplaying buying lockjaws but i missed that boat yesterday... i'm gonna get to buy them next next week at the earliest.
#2
just try to catch me
Join Date: Jul 2005
Location: waldwick, new jersey
Posts: 76
Bikes: giant stp3, giant Faith 3
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
spay wd40 or any other lube under the grip and then twist it around and then start pulling it while twisting.
#4
Senior Member
Join Date: Feb 2004
Location: Cleveland, OH
Posts: 2,304
Bikes: 2004 Trek 4600 SS, 2016 Cannondale Cujo 2 SS
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 13 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
What I did was take a cup of hot, soapy water, and put it on the ground. Make sure the glass is large enough to submerge the whole grip, then lean the grip into the water. Then, pull until you feel a hernia coming on, then keep pulling. Make sure your hand is not covering the relief hole that is on the end of the grip, otherwise it is a lot of pain for nothing. Good luck!
#7
one less horse
Originally Posted by revmonkey
i need to reuse these grips btw. and doesnt wd40 eat paint?
If you don't have an air compressor (best way), just figure out a way to get something wet and slippery (soapy water, WD40, whatever) between the grip and the bar and keep twisting.
#8
Senior Member
Join Date: Feb 2005
Location: Spain, although I'm Hungarian
Posts: 1,855
Bikes: Check signature
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Don't mean to hijack the thread but once you've taken your old grips, how do you put the new ones on? Need anything special? Or just slide them on?
#9
.
Join Date: Jul 2005
Location: "The Woo", MA
Posts: 4,831
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Originally Posted by Drunken Chicken
Don't mean to hijack the thread but once you've taken your old grips, how do you put the new ones on? Need anything special? Or just slide them on?
Put just a tiny, tiny bit of dish detergent on the end of the bar, swirl it around, and push the grip on. The grip will be a bit loose and twisty for a few days after installation. Or you could just do the old he-man, push-and-twist technique.
#10
Still kicking.
Originally Posted by revmonkey
i need to reuse these grips btw. and doesnt wd40 eat paint?
__________________
Appreciate the old bikes more than the new.
Appreciate the old bikes more than the new.
#13
Curmudgeon
Join Date: Aug 2005
Location: Nausea, New Hamster
Posts: 1,572
Bikes: (see https://wildavis.smugmug.com/Bikes) Bianchi Veloce (2005), Nishiki Cascade (1992), Schwinn Super Sport (1983)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 4 Times
in
4 Posts
This has been dealt with in a previous thread, but was such a good piece of advice, that it bears repeating here:
Take a thin-bladed screwdriver or a thin knitting-needle†, and coax it under the grip, spray WD40 into the gap, and wiggle the screwdriver/needle around and spray more WD40 and wiggle the screwdriver etc. until the grip slides off. I recently did this on some grips which had been on the bars for 12 years, and was amazed as to how effective this method proved to be!!!
Good luck!!
- Wil
† my improvement, not in the original post…
Take a thin-bladed screwdriver or a thin knitting-needle†, and coax it under the grip, spray WD40 into the gap, and wiggle the screwdriver/needle around and spray more WD40 and wiggle the screwdriver etc. until the grip slides off. I recently did this on some grips which had been on the bars for 12 years, and was amazed as to how effective this method proved to be!!!
Good luck!!
- Wil
† my improvement, not in the original post…
#14
Shreddin' heaven on his 20"
Thread Starter
Join Date: May 2005
Location: markham, ontario, canada aka chinatown north
Posts: 1,151
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
oh i got them off no problem by using white lithium grease. but now i got other problems. go check tou my thread "big problems"
#15
What?
Join Date: Oct 2003
Location: N. Tx
Posts: 1,650
Bikes: Bianchi Brava(retired), Surly Instigator(retired)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Go buy a can of compressed air, put the tube in it and put that under the grip. Spray, twist and wala, its off.
#16
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,362
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 152 Post(s)
Tagged: 1 Thread(s)
Quoted: 6218 Post(s)
Liked 4,216 Times
in
2,363 Posts
Originally Posted by Drunken Chicken
Don't mean to hijack the thread but once you've taken your old grips, how do you put the new ones on? Need anything special? Or just slide them on?
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#18
KGB Style
Join Date: Aug 2005
Posts: 158
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Originally Posted by FreeridinLoon
Go buy a can of compressed air, put the tube in it and put that under the grip. Spray, twist and wala, its off.
#19
Gamma Unit
Join Date: Oct 2005
Location: Winona Lake, IN 46590
Posts: 27
Bikes: 2006 Specialized Hardrock Sport
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Originally Posted by cyccommute
White Rain hair spray. It's cheap, slippery when wet and sticky as all get out when dry. Lots of spit works too.
#20
mmm babaghanouj.
Join Date: Aug 2003
Location: toronto, canada.
Posts: 848
Bikes: 2003 norco fluid 3.0, 2016 Intense Tracer 275C Expert
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Originally Posted by antman3249
^bump^ and for the lockjaws jenson
#21
Senior Member
Join Date: Feb 2004
Location: Cleveland, OH
Posts: 2,304
Bikes: 2004 Trek 4600 SS, 2016 Cannondale Cujo 2 SS
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 13 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Just a casual observation...many of us do not have access to compressed air. If you are replacing grips cut them off. If you are not replacing them, take them off with WARM soapy water. The warmth softens and expands the grip material, and the soap makes it slide. When putting them back on, rubbing alcohol makes a good, clean evaporating lubricant. WD40 would never come off the inside of a grip, rendering them useless and dangerous as they twist and turn at their own free will. A smattering of common sense goes a long way with bicycle repair.
#22
Shreddin' heaven on his 20"
Thread Starter
Join Date: May 2005
Location: markham, ontario, canada aka chinatown north
Posts: 1,151
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Originally Posted by rasheed
jenson's shipping costs to canada are insane. for the lockons just order them from mec.ca.
#23
Curmudgeon
Join Date: Aug 2005
Location: Nausea, New Hamster
Posts: 1,572
Bikes: (see https://wildavis.smugmug.com/Bikes) Bianchi Veloce (2005), Nishiki Cascade (1992), Schwinn Super Sport (1983)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 4 Times
in
4 Posts
Originally Posted by trekkie820
snip…
WD40 would never come off the inside of a grip, rendering them useless and dangerous as they twist and turn at their own free will. A smattering of common sense goes a long way with bicycle repair.
WD40 would never come off the inside of a grip, rendering them useless and dangerous as they twist and turn at their own free will. A smattering of common sense goes a long way with bicycle repair.
- Wil
#24
Shreddin' heaven on his 20"
Thread Starter
Join Date: May 2005
Location: markham, ontario, canada aka chinatown north
Posts: 1,151
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
actually i used white lithium grease (i soaked the insides) and about 10 minutes later the grips were on solid. SOLID.