Go Back  Bike Forums > Bike Forums > Mountain Biking
Reload this Page >

Centering Avid BB5

Notices
Mountain Biking Mountain biking is one of the fastest growing sports in the world. Check out this forum to discuss the latest tips, tricks, gear and equipment in the world of mountain biking.

Centering Avid BB5

Old 04-01-07, 01:45 PM
  #1  
If you don't look good...
Thread Starter
 
benk0's Avatar
 
Join Date: Aug 2005
Location: PHX
Posts: 284

Bikes: 1993 Cannondale Track

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Centering Avid BB5

I am on my very first mountain bike and have encountered repair issue number one.

The pads are dragging on the rear brake... I've tried every technique I could find on centering the caliper to no avail.

The bike is a Specialized P1.

Thanks in advance!
benk0 is offline  
Old 04-01-07, 01:56 PM
  #2  
later
 
free_pizza's Avatar
 
Join Date: Sep 2004
Posts: 2,471
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time in 1 Post
i dont know much about the BB5's adjustability, but have/can you adjusted the pads away from the rotor as much as they can go?

Also, depending on what pad it is rubbing on, you might have to get a spacer in between your disc and your hub. I have to do that on my cannondale in the rear.
free_pizza is offline  
Old 04-01-07, 02:17 PM
  #3  
The Rabbi
 
seely's Avatar
 
Join Date: Apr 2004
Posts: 5,125
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 16 Post(s)
Likes: 0
Liked 3 Times in 3 Posts
If you are using Avid brakes on a standard hub you shouldn't ever need a spacer behind the rotor.

Also, how much rub are we talking about? Does it actually slow the wheel? Disc brakes will almost always have some rub in a few high spots on the rotor. Do you know if it is rubbing the fixed or cable actuated side?
seely is offline  
Old 04-01-07, 02:25 PM
  #4  
later
 
free_pizza's Avatar
 
Join Date: Sep 2004
Posts: 2,471
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Originally Posted by seely
If you are using Avid brakes on a standard hub you shouldn't ever need a spacer behind the rotor.
Both my BB7 and my Juicy 5 in the rear required a spacer (on 3 different wheelsets: deore/xt/crossride) in the rear on my Cannondale.

Didnt need one on my Kona though.
free_pizza is offline  
Old 04-01-07, 02:36 PM
  #5  
The Rabbi
 
seely's Avatar
 
Join Date: Apr 2004
Posts: 5,125
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 16 Post(s)
Likes: 0
Liked 3 Times in 3 Posts
Yeah, I dont know. I've set up a few hundred Cannodales and haven't used a spacer so I don't know what to tell you. Perhaps face the tabs?
seely is offline  
Old 04-02-07, 10:48 AM
  #6  
If you don't look good...
Thread Starter
 
benk0's Avatar
 
Join Date: Aug 2005
Location: PHX
Posts: 284

Bikes: 1993 Cannondale Track

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Seely -

Thanks for the info. This is my first bike with brakes (disc ever) in a long time.

Therefore... I know NOTHING.

I'm going to let it all break in for a bit and see how it goes. It's not slowing the bike at all, I guess it's ok.

Thanks!
benk0 is offline  
Old 04-03-07, 11:46 AM
  #7  
Senior Member
 
Join Date: Nov 2006
Posts: 251
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
the way i did it on my p1 was to loosen the caliper mounting allen bolts, then squeeze the brake lever. then you just tighten the allen bolts back up while still squeezing the brake lever.

diaper eater is offline  
Old 04-03-07, 02:19 PM
  #8  
Senior Member
 
Too Rass Goat's Avatar
 
Join Date: Sep 2005
Posts: 77
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Here's what I do on my wife's Jamis w/ BB5's. They need realigned often since you do minute adjustments for pad wear via the adjustable inboard pad adjustment and pulling more cable.

Ensure the wheel is completely in the drop outs and properly secured with the QR. Loosen the cable clamp on the outside and back the adjustable inboard (spoke side) pad as far out as it will go (away from the rotor toward the spokes... assuming you still have good pads left). Loosen the allen bolts attaching the caliper and slide it into adjustment using a business card as a spacer between the rotor and inboard pad. Tighten the allen bolts, spin the wheel to check for rub. If there's no rub and only a very slight gap between the pad and rotor you can now go to the outboard via the cable and adjust it tighter to bring the outboard pad as close as possible to the rotor without rubbing. Tighten the cable clamp and you should have tight, quiet brakes. That's how I do it for any mechanical brakes that don't have both inboard & outboard adjustments, hope that helps. Don't forget to back your barrel adjusters at both the caliper and brake lever all the way back to absolute zero before doing anything...if you're the type of person that uses them to fine tune brakes. They should only be used on the trail for quick adjustment, when at home, zero them out before tuning anything.
Too Rass Goat is offline  
Old 04-03-07, 03:24 PM
  #9  
BF Risk Manager
 
Join Date: Mar 2006
Location: Snohomish County, Washington USA
Posts: 906

Bikes: Road, mountain and folding

Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 21 Post(s)
Likes: 0
Liked 3 Times in 3 Posts
Wow, TRG, this is one of the more accurate and succinct descriptions of adjusting BB5s that I have seen in a while. Very good technique, in my view.
MillCreek is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.