Assembling New Bike
#1
Junior Member
Thread Starter
Join Date: Aug 2002
Location: Western Kentucky
Posts: 20
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Assembling New Bike
I searched the forums and couldn't really find the information I need... So...
I have a new mountain bike coming in the factory box (too sweet of a deal to pass up from an aquaintance). I have been road biking for a few years and do most of my own maintenance, like derailer and brake adjustments, etc.
However, I have never seen a bike come out of a box from the factory, so I really have no idea what I am up against to put it toghether. I presume the wheels would have to put on, brakes adjusted, derailers adjusted, and pedals put on.
What else am I going to have to do?
I am quite handy with maintenance, so this doesn't bother me, I would just like to know what to expect to get any special tools ready.
Thanks in advance,
PM
I have a new mountain bike coming in the factory box (too sweet of a deal to pass up from an aquaintance). I have been road biking for a few years and do most of my own maintenance, like derailer and brake adjustments, etc.
However, I have never seen a bike come out of a box from the factory, so I really have no idea what I am up against to put it toghether. I presume the wheels would have to put on, brakes adjusted, derailers adjusted, and pedals put on.
What else am I going to have to do?
I am quite handy with maintenance, so this doesn't bother me, I would just like to know what to expect to get any special tools ready.
Thanks in advance,
PM
#2
Speed Racer
Join Date: May 2003
Location: Bend/sunriver, Oregon
Posts: 307
Bikes: Marin Quad rift zone, Haro monocoque, K2 amimal, Univega sportour
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
well my father use to own a shop and i heleped build up bikes from time to time, and out of the box they are easy to build.
mainly the derailers, brakes, headset/handlebars...ect all need to be adjusted or put on along with pedals. but small things like grips..ect vary from brand to brand. but mostly the whole bike is fairly built. should only take you around 30 min to an hour to do.
mainly the derailers, brakes, headset/handlebars...ect all need to be adjusted or put on along with pedals. but small things like grips..ect vary from brand to brand. but mostly the whole bike is fairly built. should only take you around 30 min to an hour to do.
#3
Senior Member
Join Date: Mar 2000
Location: Parrish, FL
Posts: 7,963
Bikes: Lots
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Usually, you have to install the seatpost/seat. If aluminum or steel bike, apply a thin layer of grease to the post before insertion into the seat-tube.
Then you install the stem and handlebars.
Then you slide onto the handlebars the brake levers then shifters then grips (spray inside with hairspray).
Then, install the front wheel.
Then the pedals, then make sure the crank bolt is tight and a quick check of the chainring bolts.
The cables are usually pre-cut, but I usually do a quick check before I begin my adjustments.
I then start with the front brake, adjust the shoes to align with the rim, then cable tension. I then do the same to the back wheel.
Then I adjust my front derailleur, and then the back one.
Air up the tires, recheck all bolts are tight and go for a test ride!
Recheck bolts!
L8R
Then you install the stem and handlebars.
Then you slide onto the handlebars the brake levers then shifters then grips (spray inside with hairspray).
Then, install the front wheel.
Then the pedals, then make sure the crank bolt is tight and a quick check of the chainring bolts.
The cables are usually pre-cut, but I usually do a quick check before I begin my adjustments.
I then start with the front brake, adjust the shoes to align with the rim, then cable tension. I then do the same to the back wheel.
Then I adjust my front derailleur, and then the back one.
Air up the tires, recheck all bolts are tight and go for a test ride!
Recheck bolts!
L8R
__________________
"Life is not a journey to the grave with the intention of arriving safely in a pretty and well preserved body, but rather to skid in broadside, thoroughly used up, totally worn out, and loudly proclaiming, "WOW, What a Ride!" - unknown
"Your Bike Sucks" - Sky Yaeger
"Life is not a journey to the grave with the intention of arriving safely in a pretty and well preserved body, but rather to skid in broadside, thoroughly used up, totally worn out, and loudly proclaiming, "WOW, What a Ride!" - unknown
"Your Bike Sucks" - Sky Yaeger
#5
Junior Member
Thread Starter
Join Date: Aug 2002
Location: Western Kentucky
Posts: 20
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Thank you very much for the replies! It looks like it won't be too hard, but if I get into trouble I always know I have this board!
Thanks again,
Phillip
Thanks again,
Phillip
#6
Senior Member
Join Date: Mar 2000
Location: Parrish, FL
Posts: 7,963
Bikes: Lots
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Ooops, forgot, I grease the pedals too! Thanks!
If it's a bike that goes on the showroom floor, I then add reflectors and the shop decal.
L8R
If it's a bike that goes on the showroom floor, I then add reflectors and the shop decal.
L8R
__________________
"Life is not a journey to the grave with the intention of arriving safely in a pretty and well preserved body, but rather to skid in broadside, thoroughly used up, totally worn out, and loudly proclaiming, "WOW, What a Ride!" - unknown
"Your Bike Sucks" - Sky Yaeger
"Life is not a journey to the grave with the intention of arriving safely in a pretty and well preserved body, but rather to skid in broadside, thoroughly used up, totally worn out, and loudly proclaiming, "WOW, What a Ride!" - unknown
"Your Bike Sucks" - Sky Yaeger