Go Back  Bike Forums > Bike Forums > Mountain Biking
Reload this Page >

need reassurance!!

Notices
Mountain Biking Mountain biking is one of the fastest growing sports in the world. Check out this forum to discuss the latest tips, tricks, gear and equipment in the world of mountain biking.

need reassurance!!

Old 03-12-14, 07:45 AM
  #1  
Junior Member
Thread Starter
 
Join Date: Feb 2014
Location: El Chorro Spain.
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
need reassurance!!

I now have a bike a second hand one. I´m really pleased with it. However, I see that I have the quick release clips on both wheels. It is the front one that I ´m not sure of. On the front wheel there is the hydraulic cable connection to the wheel. I want to take the wheel off, when I need to put the bike in the car. is it a case of just unscrewing the hydraulic cable from the disc, to get the wheel off for travelling after loosening the quick release clip on the wheel, and then reattach the hydraulic setup, when i´m out and about on my bike? Might sound daft but I`ve not had either hydraulic or quick release clips on a bike before.
chorroas66 is offline  
Old 03-12-14, 07:59 AM
  #2  
Zip tie Karen
 
Phil_gretz's Avatar
 
Join Date: Aug 2009
Location: Fair Oaks Ranch, TX
Posts: 7,006

Bikes: '13 Motobecane Fantom29 HT, '16 Motobecane Turino Pro Disc, '18 Velobuild VB-R-022, '21 Tsunami SNM-100

Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 1465 Post(s)
Liked 1,542 Times in 806 Posts
Well, it's probably not what you think. Perhaps you could take a photograph and post it here?

The usual hydraulic line on a mountain bike is a connection between the hand lever for the brake and the brake caliper, which squeezes around the disc rotor. It is the rotor that is connected to your wheel (via bolts surrounding one side of the hub). The disc slip within a narrow slot in the brake caliper, which is mounted by bolts onto your front fork.

So, when you release the quick release lever (and maybe continue to back off the opposing nut a bit), the wheel should be free to move out from its slot and drop from the fork. You will see the rotor disc slip out of its caliper slot as the wheel drops, too.

When you put the wheel back on, make certain to guide the rotor disc back into its caliper slot, and then the quick release lever and hub back into its fork end. Adjust axle nut so that lever tightness begins to make contact with the fork when the lever is in pointing straight away from the bike. It should clamp firmly with finger pressure to close fully. It it is too easy to fully close, then the nut needs a turn or two more to tighten. If it's too difficult to fully close the lever, then the nut needs to back away a turn or two.

Before tightening the lever fully, make certain that the disc rotor is centered within the brake caliper. You can check this by peering into the slot, maybe with a small light held behind it, or something white as a background, so that you can see the tiny gap on either side of the disc rotor.

Hope that this helps you.
Phil_gretz is offline  
Old 03-12-14, 08:04 AM
  #3  
Zip tie Karen
 
Phil_gretz's Avatar
 
Join Date: Aug 2009
Location: Fair Oaks Ranch, TX
Posts: 7,006

Bikes: '13 Motobecane Fantom29 HT, '16 Motobecane Turino Pro Disc, '18 Velobuild VB-R-022, '21 Tsunami SNM-100

Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 1465 Post(s)
Liked 1,542 Times in 806 Posts
Diagram here: Basic Bicycle Anatomy 101 - Brake Systems - greatescapebikes.com

Video of disc mtb wheel removal: Video: Remove Mountain Bike Wheels | eHow
Phil_gretz is offline  
Old 03-12-14, 09:57 AM
  #4  
Junior Member
Thread Starter
 
Join Date: Feb 2014
Location: El Chorro Spain.
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Thank You!!

The video and info very helpful. Now I know I don´t need to take off the brake caliper just to get the front wheel off!!
chorroas66 is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Bad Lag
Bicycle Mechanics
9
06-05-19 12:43 PM
plgcp
Bicycle Mechanics
4
06-12-15 02:38 PM
John Kelin
Bicycle Mechanics
7
12-16-13 02:03 PM
Commutertoddo
Bicycle Mechanics
6
06-04-11 11:15 AM
Bill Horn
Bicycle Mechanics
5
12-13-10 09:04 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.