Bike Forums

Go Back  Bike Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: etskyy
Showing results 1 to 9 of 9
Search took 0.01 seconds.
Forum: Bicycle Mechanics
04-05-22, 04:19 PM
Replies: 8
Views: 1,115
Posted By KCT1986

Yes, you should measure the chainline at the...

Yes, you should measure the chainline at the cassette. This will give you some idea of how different the proposed new crank/BB combo will be.

Although, how much of an affect it haves will depend...
Forum: Bicycle Mechanics
04-05-22, 04:09 PM
Replies: 8
Views: 1,115
Posted By dedhed

AS well as interface. Sounds like Octalink but is...

AS well as interface. Sounds like Octalink but is it V1 or V2 octalink?
Forum: Bicycle Mechanics
04-05-22, 03:40 PM
Replies: 8
Views: 1,115
Posted By alcjphil

When you are changing both bottom bracket and...

When you are changing both bottom bracket and crank the measurements of the old stuff really doesn't matter. Chainline for a mountain bike crank with its recommended bottom bracket will be slightly...
Forum: Bicycle Mechanics
04-05-22, 02:58 PM
Replies: 8
Views: 1,115
Posted By Iride01

Chain line on a FC-M300 was supposed to be about...

Chain line on a FC-M300 was supposed to be about 47 mm with a 122 mm square taper BB.

Alivio FC-T4010 says it's chain line is 50 mm. Maybe, maybe not enough of a difference for your shifting...
Forum: Bicycle Mechanics
04-05-22, 02:08 PM
Replies: 8
Views: 1,115
Posted By Iride01

I think the Giant Trooper came in quite a few...

I think the Giant Trooper came in quite a few versions through the years. So it'd help to narrow down what year yours is.

If that ISO number is on the BB then it might be a BB cartridge and when...
Forum: Classic & Vintage
08-28-20, 11:44 AM
Replies: 8
Views: 1,663
Posted By randyjawa

For me, the answer, from a dollars and cents...

For me, the answer, from a dollars and cents point of view, the answer would be no. However...

The bike looks to be an easy "street restoration" and a great learning opportunity. The cost to get...
Forum: Classic & Vintage
08-27-20, 01:59 PM
Replies: 8
Views: 2,198
Posted By dddd

The fix for not having the needed selection of...

The fix for not having the needed selection of shims can be to sand down the seating surface of the cone using wet/dry 240 grit or similar on a flat surface.

Be prepared to test-fit the cone...
Forum: Classic & Vintage
08-27-20, 11:03 AM
Replies: 8
Views: 1,663
Posted By T-Mar

While it may have been manufactured in Germany,...

While it may have been manufactured in Germany, the presence of of a light bracket on the right fork blade suggests it was marketed in a country where they drive on the left side of the road, such as...
Forum: Classic & Vintage
08-27-20, 09:19 AM
Replies: 8
Views: 1,663
Posted By juvela

------ it is german made and looks to date...

------

it is german made and looks to date from the later 1970's, or possibly into the early 1980's

BSC thread headset and bottom bracket

there is a manufacturer of cycles in Germany called...
Showing results 1 to 9 of 9


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.