Speedplay pedal what do you use for greasing
08-10-16, 11:42 AM
#2
Senior Member
Join Date: Sep 2008
Location: Beautiful Long Beach California
Posts: 3,603
Bikes: Eddy Merckx San Remo 76, Eddy Merckx San Remo 76 - Black Silver and Red, Eddy Merckx Sallanches 64 (2); Eddy Merckx MXL;
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 143 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
I use a Finish Line Grease Gun ($20 from performance bike) along with Finish Line Grease.
Finish Line Grease Injection Pump Gun
Finish Line Grease Injection Pump Gun
08-10-16, 12:29 PM
#4
Cycliste sérieux
Join Date: Jan 2013
Posts: 466
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 64 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
08-10-16, 06:43 PM
#6
Senior Member
Join Date: Jan 2010
Location: TC, MN
Posts: 39,505
Bikes: R3 Disc, Haanjo
Mentioned: 353 Post(s)
Tagged: 1 Thread(s)
Quoted: 20789 Post(s)
Liked 9,429 Times
in
4,662 Posts
If you're going to go this route, to me, it's easiest to pull the pedals, stand them upright on your desk/bench, put the syringe on top and push down on the plunger while keeping the stack aligned.
08-10-16, 07:46 PM
#7
Slacker
Join Date: May 2009
Location: North Orange County, in Southern California
Posts: 1,295
Bikes: 1986 Peugeot Orient Express, 1987 Trek 560 Pro, 1983 SR Semi Pro, 2010 Motobecane Le Champion Titanium, 2011 Trek Fuel EX8
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 97 Post(s)
Liked 6 Times
in
4 Posts
08-10-16, 08:25 PM
#9
Cycliste sérieux
Join Date: Jan 2013
Posts: 466
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 64 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I'll second this recommendation. You do need something which allows a bit of force to be applied, at least if you grease them as I do. I remove just the screw from the plastic cap, and then push the grease gun hard enough into the resulting hole so as to make a reasonable seal. Then pump the grease in until it comes out the other side of the pedal. To be clear, I remove the screw only, not the plastic cap.
08-11-16, 04:55 AM
#10
Fatty McFatcakes
Join Date: Nov 2013
Location: Krispy Kreme
Posts: 987
Bikes: Aero Cheeseburger w/ Sr(h)am eBacon
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 245 Post(s)
Likes: 0
Liked 2 Times
in
1 Post
I have a plastic syringe. You can probably buy one at your drug store for a buck.
https://www.beenleighfarmsupplies.com...nge%2010ml.jpg
EDIT: Sorry, just looked it up. It's $3.
https://www.beenleighfarmsupplies.com...nge%2010ml.jpg
EDIT: Sorry, just looked it up. It's $3.
As for pedal grease, I use Park Tool Polylube 1000. You can get it for $6-$8 /tube. Lasts forever. I use it for all bike lube needs.
08-11-16, 05:41 AM
#11
Senior Member
Join Date: Jan 2010
Location: TC, MN
Posts: 39,505
Bikes: R3 Disc, Haanjo
Mentioned: 353 Post(s)
Tagged: 1 Thread(s)
Quoted: 20789 Post(s)
Liked 9,429 Times
in
4,662 Posts
Good for you, but if you can't maintain a firm coupling because of viscosity, or robustness of bike stand, etc, pulling the pedals off can make things much easier and it adds about 30 seconds to the job. Pretty simple.
08-11-16, 06:29 AM
#13
Senior Member
Join Date: Jul 2007
Posts: 7,557
Mentioned: 54 Post(s)
Tagged: 0 Thread(s)
Quoted: 1849 Post(s)
Liked 667 Times
in
421 Posts
I've always done it with the syringe and pedals on the bike. Sometimes, I just lean the bike against the wall.
One other thing, OP, make sure you have a rag to catch all the nasty black gunk that comes out near the spindle.
One other thing, OP, make sure you have a rag to catch all the nasty black gunk that comes out near the spindle.
