star-fangled nut, spacers, trimming steer tube...
#1
Senior Member
Thread Starter
Join Date: Dec 2005
Location: O'Fallon, MO
Posts: 242
Bikes: 1973 Raleigh Professional, 1993 Raleigh Technium Olympian, 2006 Cervelo Dual, 2008 Cannondale Caad8, 2010 Kona Unit, 2013 Trek Superfly 100 AL Pro, 2014 Trek Crockett 9, 2017 All City Nature Boy 853
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
star-fangled nut, spacers, trimming steer tube...
A few quick questions on getting my front end set up correctly. The fork in question is carbon with an aluminum steer tube. Assuming that I have my position dialed in...
1) Is there any advantage to keeping a very slim spacer between the headtube cap and stem, or is it better to put the stem directly against the headset cap?
2) What about spacers above the stem? Is it better to keep one above the stem or to trim the tube such than no spacer is above the stem?
3) How difficult is it to install a new star-fangled nut? What's the procedure? How do you secure the fork/steer tube when installing the nut? Do I need a specialized tool to do the job correctly?
4) What do you use to cut the steer tube? I know a hacksaw will work, but it seems that hand-held "pipe cutter" would produce a cleaner & straighter cut. But, will it cut a steer tube? Seems like it's much thicker than what the tool is designed for.
Thanks.
Steve
1) Is there any advantage to keeping a very slim spacer between the headtube cap and stem, or is it better to put the stem directly against the headset cap?
2) What about spacers above the stem? Is it better to keep one above the stem or to trim the tube such than no spacer is above the stem?
3) How difficult is it to install a new star-fangled nut? What's the procedure? How do you secure the fork/steer tube when installing the nut? Do I need a specialized tool to do the job correctly?
4) What do you use to cut the steer tube? I know a hacksaw will work, but it seems that hand-held "pipe cutter" would produce a cleaner & straighter cut. But, will it cut a steer tube? Seems like it's much thicker than what the tool is designed for.
Thanks.
Steve
#2
Senior Member
Join Date: Aug 2005
Posts: 1,616
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Originally Posted by The_Mickstar
A few quick questions on getting my front end set up correctly. The fork in question is carbon with an aluminum steer tube. Assuming that I have my position dialed in...
1) Is there any advantage to keeping a very slim spacer between the headtube cap and stem, or is it better to put the stem directly against the headset cap? Spacers allow you to adjust the degree of drop from your seat to your handlebars.
2) What about spacers above the stem? Is it better to keep one above the stem or to trim the tube such than no spacer is above the stem? See answer to #1 above. It is a good idea to move spacers around above and below the stem until you have dialed-in your fit. Then you remove all spacers above the stem and cut your steerer accordingly. Spacers above the stem should only be temporary.
3) How difficult is it to install a new star-fangled nut? What's the procedure? How do you secure the fork/steer tube when installing the nut? Do I need a specialized tool to do the job correctly? Parktool has step-by-step instructions, with pictures:
https://www.parktool.com/repair/readhowto.asp?id=111
4) What do you use to cut the steer tube? I know a hacksaw will work, but it seems that hand-held "pipe cutter" would produce a cleaner & straighter cut. But, will it cut a steer tube? Seems like it's much thicker than what the tool is designed for. See answer to #3 above.
Thanks.
Steve
1) Is there any advantage to keeping a very slim spacer between the headtube cap and stem, or is it better to put the stem directly against the headset cap? Spacers allow you to adjust the degree of drop from your seat to your handlebars.
2) What about spacers above the stem? Is it better to keep one above the stem or to trim the tube such than no spacer is above the stem? See answer to #1 above. It is a good idea to move spacers around above and below the stem until you have dialed-in your fit. Then you remove all spacers above the stem and cut your steerer accordingly. Spacers above the stem should only be temporary.
3) How difficult is it to install a new star-fangled nut? What's the procedure? How do you secure the fork/steer tube when installing the nut? Do I need a specialized tool to do the job correctly? Parktool has step-by-step instructions, with pictures:
https://www.parktool.com/repair/readhowto.asp?id=111
4) What do you use to cut the steer tube? I know a hacksaw will work, but it seems that hand-held "pipe cutter" would produce a cleaner & straighter cut. But, will it cut a steer tube? Seems like it's much thicker than what the tool is designed for. See answer to #3 above.
Thanks.
Steve