First ride on new bike w/SRAM- question
#1
...
Thread Starter
Join Date: Jan 2008
Location: nyc
Posts: 978
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
First ride on new bike w/SRAM- question
I got my Pedal Force RS2 with SRAM Rival built yesterday. On it's inaugural ride, it was skipping gears, more like when I would shift up/down, it would lag a bit behind. Even when I'm in the gear I want to be in, it sounds like the sound I would get if I was cross chaining (which I'm not).
Maybe I need to get used to the double tap.
I either, A, need to break in the drivetrain, or B, get my chain/FD, RD adjusted.
Thanks.
Maybe I need to get used to the double tap.
I either, A, need to break in the drivetrain, or B, get my chain/FD, RD adjusted.
Thanks.
#3
Keep on climbing
I'd say you need a little tweak to the rear derailleur. The derailleur pulleys need to line up exactly under the cog the chain is on. See: https://www.parktool.com/repair/readhowto.asp?id=64. Just scroll down to the section on "index setting". All you need is a good set of eyes, your hands, and some patience.
#4
Senior Member
Join Date: Jan 2008
Location: Buffalo, NY
Posts: 337
Bikes: an amazing Fuji Newest 3.0!
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
If it sounds like it's skipping even when it's in gear it's probably just a simple barrel adjustment.
#5
Senior Member
Join Date: Jun 2007
Posts: 230
Bikes: a green one and a black one
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
If it's not shifting well, then some adjusting is needed. Once it's shifting well, you may still have some "rumbling" on certain cogs, but that goes away after a little mileage. I've put on two new SRAM cassettes and had this with both, but man, did I sweat about it the first time!
#7
Zircon Encrusted Tweezer
Join Date: May 2004
Location: Marshfield, MA
Posts: 1,016
Bikes: Pivot Switchblade, SantaCruz Tallboy, SantaCruz Solo, Specialized Fatboy, Trek ProjectOne Madone, Fuji Altamira CX 1.1, Lemond Zurich
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Once you're ruled out all of the above, if your frame has internal cable routing, make sure the derailleur cables aren't crossed inside the frame.
#8
Senior Member
Join Date: Jul 2005
Location: Davis, CA
Posts: 1,183
Bikes: K2 Zed 3.0; Motobecane Le Champion; Pedal Force RS; IRO BFGB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
One minor detail that I missed when I installed my Red group was the proper rear cable routing. It caused all kinds of weird gear skipping. Luckily, I caught it on the repair stand. The SRAM rear derailleurs do not rout the cables like Shimano or Campagnolo. There is a grooved channel that the cable runs in after it leaves the housing/stop before it's bolted down. If the cable is not in this groove, it won't function properly. Not that this is what's happening in your case but something to throw out into the ether for other to discover.
#10
Senior Member
Join Date: Nov 2006
Location: Los Alamos, NM
Posts: 903
Bikes: 2008 fetish illustre
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 10 Post(s)
Likes: 0
Liked 8 Times
in
1 Post
Oh and FWIW, if your shifting acts up again, one small click turn of the RD barrel adjuster will likely fix it. Cables do tend to stretch.