Go Back  Bike Forums > Bike Forums > Road Cycling
Reload this Page >

2007 Schwinn LeTour with Ritchey Biomax II handlebar installed

Notices
Road Cycling “It is by riding a bicycle that you learn the contours of a country best, since you have to sweat up the hills and coast down them. Thus you remember them as they actually are, while in a motor car only a high hill impresses you, and you have no such accurate remembrance of country you have driven through as you gain by riding a bicycle.” -- Ernest Hemingway

2007 Schwinn LeTour with Ritchey Biomax II handlebar installed

Old 10-11-08, 09:42 AM
  #1  
Senior Member
Thread Starter
 
Join Date: Jun 2007
Location: Kingsport, TN
Posts: 270

Bikes: 2007 Schwinn Le Tour

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
2007 Schwinn LeTour with Ritchey Biomax II handlebar installed

After repeatedly adjusted the stock handlebar on the 2007 Schwinn LeTour, I can't get my wrist to stop hurting. Then I did some more research and took some measurements and realized I have a 38cm shoulder and the stock handlebar is 44cm. I realized a new handlebar is needed to make the bike fits me.

I got the handlebar at www.aebike.com, it was the usual quick turnaround. I ordered it on a Sunday and I got it on Friday. I paid about $61.49 out the door. Installation of the bar was very easy, and I wrapped the new bar with some cheapo Forte Gel Tape. Nothing fancy but looks ok.

I also took the opportunity to transplant the Brooks saddle from my mountain bike to the new bike.

Here are some pictures:







This is my first attempt at wrapping a handlebar, I think I did ok. Both sides are not quite even.




Review of the Ritchey Biomax II handlebar:
The handlebar is awesome. Now I can ride comfortably without my wrist hurting. The construction is very solid and it's much lighter than the stock handlebar. However, due to the location of the thumb actuated shifters of the Sora group, I adjusted the handlebar in a position most suitable for riding on the hood, and that sacrifice some usability for the drops. However, I can still ride in the drops and reach for the brakes well during downhill dashes.

I am now a complete convert of the Brooks saddle. The stock saddle (Selle San Marco Ischia) was quite comfortable with bike shorts, but rode about 14 miles on a commute without bike shorts and it was quite painful. Now, with the Brooks installed, the difference was between stadium bench and a nice office chair. The first time I sat back onto the Brooks, I just go "oooooooohhhhh"

Due to my busy work schedule, I just get to ride it 10 miles at a time for about 40 minutes twice a week. The bike is now real joy to ride. The drivetrain and brake pad is still a little left to desire but for $412 for the bike and about $112 worth of new parts (new handler, stem and pedals). It's not bad of a deal.
earthworm94 is offline  
Old 10-11-08, 11:20 PM
  #2  
Wheelsuck
 
Fat Boy's Avatar
 
Join Date: Jun 2007
Posts: 6,158
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Where are the tri-bars?
Fat Boy is offline  
Old 10-12-08, 02:07 AM
  #3  
Cat 666
 
fatallightning's Avatar
 
Join Date: Jul 2008
Location: nyack, ny (yes, that one)
Posts: 1,462
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
you should have gone in the other direction, so that twisting the grips would tighten the tape instead of loosening it.
fatallightning is offline  
Old 10-12-08, 11:28 AM
  #4  
Senior Member
 
Bontrager's Avatar
 
Join Date: Dec 2004
Location: Boulder, CO
Posts: 2,339

Bikes: Road, MTB, Folding, Commuting bikes...

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Why are your brifters turned so far in??

You know when you put that saddle on your bike, you modified the height and fore/aft position (in addition to your handlebars) so you hbar change may have less of an impact on your painful wrists now than if you left your old seat on.

ParkTools has a good writeup on how to wrap handlebar tape.
Bontrager is offline  
Old 10-12-08, 07:57 PM
  #5  
Senior Member
Thread Starter
 
Join Date: Jun 2007
Location: Kingsport, TN
Posts: 270

Bikes: 2007 Schwinn Le Tour

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by Bontrager
Why are your brifters turned so far in??

You know when you put that saddle on your bike, you modified the height and fore/aft position (in addition to your handlebars) so you hbar change may have less of an impact on your painful wrists now than if you left your old seat on.

ParkTools has a good writeup on how to wrap handlebar tape.
I thought the brifters should be in-line with angle of the hood part of the handlebar. The camera exaggerated the "turn-in" further. I had adjusted the brifters back out a bit since.

I had wrist pain before the handlebar swap partly because the handlebar is 44cm and my shoulder is only measures about 39cm. Also, the reach for that bar is a bit too much. I did adjust the saddle for my legs after I install the new saddle. Now the wrist pain is largely gone. Before, I keep "tossing and turning" all over the bar, which is to a degree what one suppose to do as to take advantage of multiple hand positions offered by dropbars. However, I shouldn't need to change hand position all the time for a 6 mile ride. Now, with the new handlebar, I can stay in pretty much the same place all the time for a 10 mile ride.

I did compromise the position to be most comfortable when riding on the hood because of the way the Sora group works. One of the shifter button is operated by the thumb so I ride mostly on the hood. If anyone have any "best of both worlds" solution, or adjusting the brifters position so it's comfortable for both on the hood and on the drops, please let me know.

Thanks.
earthworm94 is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.