Will Yokozun Reaction cables work with Madone's 6 series internal Cable routing?
#1
Senior Member
Thread Starter
Join Date: Aug 2010
Location: Bay Area, Duh!
Posts: 325
Bikes: Caad 9.5, Madone 6 series, Speed Concept 7 series.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Will Yokozun Reaction cables work with Madone's 6 series internal Cable routing?
Will Yokozun Reaction cables work with Madone's 6 series internal Cable routing?
I've researched but could not find an answer. I asked the guys from competitive cycling but they were unsure and suggested I order them and returned them in case they did not work. I rather just know if the diameter of the cables will work with the inner tubes.
Any first hand experience.
Thanks.
I've researched but could not find an answer. I asked the guys from competitive cycling but they were unsure and suggested I order them and returned them in case they did not work. I rather just know if the diameter of the cables will work with the inner tubes.
Any first hand experience.
Thanks.
#2
Senior Member
Join Date: Jan 2009
Location: GA
Posts: 1,155
Bikes: Helix, HonkyTonk, NailTrail
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
Will Yokozun Reaction cables work with Madone's 6 series internal Cable routing?
I've researched but could not find an answer. I asked the guys from competitive cycling but they were unsure and suggested I order them and returned them in case they did not work. I rather just know if the diameter of the cables will work with the inner tubes.
Any first hand experience.
Thanks.
I've researched but could not find an answer. I asked the guys from competitive cycling but they were unsure and suggested I order them and returned them in case they did not work. I rather just know if the diameter of the cables will work with the inner tubes.
Any first hand experience.
Thanks.
NOTE: Brake housing is stiffer than normal housing. Set-ups that need tighter bends may not be possible with our brake housing.
#3
I eat carbide.
Join Date: Jan 2006
Location: Elgin, IL
Posts: 21,627
Bikes: Lots. Van Dessel and Squid Dealer
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 1325 Post(s)
Liked 1,306 Times
in
560 Posts
I have run it internal a few times but all on AeroCat Frames with no issue. Also on Specialized CruX frames as well...
__________________
PSIMET Wheels, PSIMET Racing, PSIMET Neutral Race Support, and 11 Jackson Coffee
Podcast - YouTube Channel
Video about PSIMET Wheels
Podcast - YouTube Channel
Video about PSIMET Wheels
#4
Senior Member
Thread Starter
Join Date: Aug 2010
Location: Bay Area, Duh!
Posts: 325
Bikes: Caad 9.5, Madone 6 series, Speed Concept 7 series.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Yeah, i'm not really concern about the under bar tape cables since I have a dura ace 7800 set up and the derailer cables will be exposed. The brake lines under the tape, well they would not really be tighter bends than normal, would they?
Just concerned about the diameter of the cable fitting the inner housing.
Thanks guys, i'll give them a try.
Just concerned about the diameter of the cable fitting the inner housing.
Thanks guys, i'll give them a try.
Last edited by BayAreaUser; 01-17-11 at 09:36 PM.