Time to renovate the old road bike, help & suggestions?
05-14-11, 08:45 AM
#1
Junior Member
Thread Starter
Join Date: May 2011
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Time to renovate the old road bike, help & suggestions?
Hi,
I have an old road bike (raleigh frame) with I guess original gearings, cassettes, chainset (They are so worn out so I can't see the model names) from somewhere in the 80's. It is in bad need of some renovation and I'll try to stay within a low budget.
Currently it's using a 52/41 chainset setup.. and a 6 speed rear cassette, the wheels are 700C.
Parts to be changed:
And these are the parts I'm planning:
And I'm unsure about the width between the rear dropouts, from outside to outside the dropouts I measured 130mm. But should I count from center to center of each dropout? In that case I most likely have a 126mm width and the WH-R500 wheel is 130mm between the locknuts. What do I do? Any suggestions of other parts?
I'm from Sweden so I have to order most of my stuff from europe because of the customs, usually through the UK: chainreactioncycles.com, wiggle.co.uk, amazon.co.uk and ebay.co.uk - Though I haven't found anything on amazon or ebay yet with cheaper total than the stores.
Any tips?
I have an old road bike (raleigh frame) with I guess original gearings, cassettes, chainset (They are so worn out so I can't see the model names) from somewhere in the 80's. It is in bad need of some renovation and I'll try to stay within a low budget.
Currently it's using a 52/41 chainset setup.. and a 6 speed rear cassette, the wheels are 700C.
Parts to be changed:
- Rear Wheel
- Cassette
- Chainset
- Front & Rear derailleurs
And these are the parts I'm planning:
- Rear Wheel: Shimano WH-R500
- Cassette: Shimano Tiagra, 9sp, HG50 (11-25)
- Chainset: Shimano 2300 (52/39, 170mm or 175mm?)
- Front derailleur: Shimano Tiagra, Double, 9sp, 4500
- Rear derailleur: Shimano 105, 5700 (difference between medium & short cage?)
And I'm unsure about the width between the rear dropouts, from outside to outside the dropouts I measured 130mm. But should I count from center to center of each dropout? In that case I most likely have a 126mm width and the WH-R500 wheel is 130mm between the locknuts. What do I do? Any suggestions of other parts?
I'm from Sweden so I have to order most of my stuff from europe because of the customs, usually through the UK: chainreactioncycles.com, wiggle.co.uk, amazon.co.uk and ebay.co.uk - Though I haven't found anything on amazon or ebay yet with cheaper total than the stores.
Any tips?
05-14-11, 09:09 AM
#2
Former Hoarder
Your rear is 126 but can be cold set to accommodate.
I think you'll need a new chain as well.
I think you'll need a new chain as well.
__________________
05-14-11, 12:33 PM
#4
Senior Member
Join Date: Sep 2009
Location: Grayslake, IL
Posts: 54
Bikes: '74 Ral SuperCourse II, '77? Ron Cooper, '82 Scapin Sprint?, '84 Ross Sig, '86 Voyageur, '86 Miy. 512, '87 Prologue, '87 Circuit, '91 MP21, '96? DeBernardi, '14 Dolan Mythos, Giordano Tandem, '18 Masi Alare.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Liked 1 Time
in
1 Post
Cruise ebay for used component groups, I've seen Shimano Sora groups for $100 and up. Take a very close look at the photo's, you don't want to buy something that's all beat up. A bike shop in the US would charge you around $150 in labor to install such goodies. Since you're thinking of 105 and/or Tiagra level components, may I suggest you just go ahead and buy a new bike to be more cost effective? You may be able to get a substantial discount on a new 2010 or earlier year model. Good luck!
05-14-11, 12:48 PM
#5
Senior Member
Join Date: Mar 2011
Location: Sacramento area
Posts: 68
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Agreed. More cost effective to buy a new bike with components unless you have some attachment to the frame. Sell the old bike for what you can get for it.
05-17-11, 03:29 PM
#6
Junior Member
Thread Starter
Join Date: May 2011
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I have a new bike, for my long distance triathlon purposes a Felt S22 '10.
This is sort of a project for me to my brother so he will have a decent ride later this summer, I will use a sora front & rear derailleur instead - just for a lower budget.
The whole renovation will cost about $180-200 all in all, this includes new parts and a stylish paintjob (this is considered cheap where I live). About new bikes, it's nearly impossible to find racers for lower than $160, that's what my brother had to pay for this Raleigh with a Reynolds 501 frame. For any USED '05-'10 model I would have to pay around $650-$2300, that's the prices that set the standard here.
I ordered my Felt S22 from the UK for $1550 (brand new incl. delivery costs), the cheapest one I found in Sweden had a pricetag of $2600 (this is how it is with most of the bikes & pricings around here, same goes for running shoes..)
To the project:
I have stripped the bike, which wasn't the easiest task, for the record I broke 2 lockring tools getting the lockring up. Years of friction took its toll I guess, the fixed cup on the other side wasn't and easy task either. I don't own a 36mm spanner to solve the problem, so I used Sheldon Brown's technique where you use a bolt, a nut and a few plates and screw until friction does its work and takes the cup with it.
First attempt ended up with a thick steel nut becoming round, literally. So I managed to unscrew the whole rigg and take a new nut and do it all over again. This time after hanging on the spanner, the cup eventually unscrewed after enough friction from the bolt, nut & plates.
Now when all parts are loose I've started to grind away the old color of the frame with a wired wheel, done about half so far. By the weekend (hopefully) I will start with the paintjob which will be a matte black base with orange and maybe white stripes & details to it.
Cheers
This is sort of a project for me to my brother so he will have a decent ride later this summer, I will use a sora front & rear derailleur instead - just for a lower budget.
The whole renovation will cost about $180-200 all in all, this includes new parts and a stylish paintjob (this is considered cheap where I live). About new bikes, it's nearly impossible to find racers for lower than $160, that's what my brother had to pay for this Raleigh with a Reynolds 501 frame. For any USED '05-'10 model I would have to pay around $650-$2300, that's the prices that set the standard here.
I ordered my Felt S22 from the UK for $1550 (brand new incl. delivery costs), the cheapest one I found in Sweden had a pricetag of $2600 (this is how it is with most of the bikes & pricings around here, same goes for running shoes..)
To the project:
I have stripped the bike, which wasn't the easiest task, for the record I broke 2 lockring tools getting the lockring up. Years of friction took its toll I guess, the fixed cup on the other side wasn't and easy task either. I don't own a 36mm spanner to solve the problem, so I used Sheldon Brown's technique where you use a bolt, a nut and a few plates and screw until friction does its work and takes the cup with it.
First attempt ended up with a thick steel nut becoming round, literally. So I managed to unscrew the whole rigg and take a new nut and do it all over again. This time after hanging on the spanner, the cup eventually unscrewed after enough friction from the bolt, nut & plates.
Now when all parts are loose I've started to grind away the old color of the frame with a wired wheel, done about half so far. By the weekend (hopefully) I will start with the paintjob which will be a matte black base with orange and maybe white stripes & details to it.
Cheers
