Go Back  Bike Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: rvtraveller
Showing results 1 to 12 of 12
Search took 0.01 seconds.
09-04-21, 01:59 AM
Replies: 11
Views: 594
Posted By rvtraveller

It worked

SPLICING THE WIRE HARNESS WORKED. Due to the bicycle parts shortage, it took me seven months to gather a mix of new and used parts (from five different countries) before I could build and install the...
09-01-21, 11:25 PM
Replies: 1
Views: 160
Posted By rvtraveller

I assembled the hub/cog/shift-motor today and...

I assembled the hub/cog/shift-motor today and installed the wheel on the bike. The rear cog CANNOT be reversed on a Di2 Alfine transmission. On each side of the cog, there's >1mm clearance for my...
08-30-21, 08:24 PM
Replies: 1
Views: 160
Posted By rvtraveller

Alfine Di2 Question

Can anyone tell me if I can reverse the dished Nexus cog on a Di2 Alfine 11 speed? Again, this is specific to the Di2 version. I'm about to install the 18T cog and MU-S705 shifter motor on a new...
05-11-21, 01:10 PM
Replies: 11
Views: 594
Posted By rvtraveller

Reply to Troul: Thanks for your reply The...

Reply to Troul:

Thanks for your reply The 3-plug harness is a Shimano part. It has the same connectors and cable as the straight wires, so I don't expect any more problems with water than using...
05-10-21, 09:47 PM
Replies: 11
Views: 594
Posted By rvtraveller

Thanks, Badger6

Thanks for your reply, Badger6. I can't auto-quote you here yet because I need to log more posts per the forum rules. But, I've copied your comments below my reply.

I've measured everything. The...
05-10-21, 02:19 PM
Replies: 11
Views: 594
Posted By rvtraveller

Proposed part numbers for Di2 system

These are the parts to be connected:

MU-S705 - motor unit at IGH transmission

SM-BMR2 - mount for external battery

SC-S705 - gear indicator display (attaches independently to SW-S705 shifter...
05-10-21, 11:36 AM
Replies: 11
Views: 594
Posted By rvtraveller

"Dumb Junction Box"

Moments ago, I found the reference below at bettershifting.com, so I'm still hopeful. Anyone else have thoughts?

"Junction A: The junction box at the front of the bike. Either below the stem,...
05-10-21, 11:27 AM
Replies: 11
Views: 594
Posted By rvtraveller

Hello, Barry. Thanks for your reply. The junction...

Hello, Barry. Thanks for your reply. The junction box I would use is the SM-JC41 (SM-JC40 as alternative). Unlike some Di2 junctions, the JC-41 and JC-40 have no buttons or any obvious function...
05-10-21, 01:58 AM
Replies: 11
Views: 594
Posted By rvtraveller

Di2 Alfine E-tube Savings and Shortcut

Did I find savings and a shortcut? I'm buying parts to replace the existing IGH transmissions on two bikes. The new stuff is Shimano Alfine IGH with Di2 shifting. My setup has only three electronic...
04-16-21, 04:28 AM
Replies: 4
Views: 596
Posted By rvtraveller

Hello, *Scuba. I can't read your private message....

Hello, *Scuba. I can't read your private message. A pop-up text box informs me that I can't use PM until I've posted 10 times. Will you please send the text of the unread PM to my e-mail? Thanks, Al.
04-14-21, 03:42 AM
Replies: 4
Views: 596
Posted By rvtraveller

Hello, Scuba. Thanks for your reply. I'm...

Hello, Scuba. Thanks for your reply. I'm encouraged already. I've identified what I think are the correct part numbers for the job after reading online. I need the shop to confirm my parts list is...
04-09-21, 03:17 PM
Replies: 4
Views: 596
Posted By rvtraveller

Vancouver Shop with Shimano IGH sales expertise?

Hello. I've been planning two (2) identical rear wheel builds using Shimano's Alfine 11-speed internal gear hub. Shifters will be Shimano electric Di2. Build labour and rim, spokes, and more to be...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.