Go Back  Bike Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: Sander Saares
Showing results 1 to 12 of 12
Search took 0.01 seconds.
05-09-11, 01:29 AM
Replies: 15
Views: 3,194
Posted By Sander Saares

Ok, thanks for the advice. I bought some new...

Ok, thanks for the advice. I bought some new bibs, so let's see what comes of this. I hope they work better.
05-06-11, 03:07 AM
Replies: 15
Views: 3,194
Posted By Sander Saares

Bibs misalignment - pad rides too far up front

The padded area of my bibs rides up front within minutes after I set myself up right. The end result is that my sitbones are directly on top of the rearmost seams where the pad is joined with the bib...
04-19-11, 01:03 AM
Replies: 21
Views: 6,233
Posted By Sander Saares

Thank you for your suggestions, everyone! I took...

Thank you for your suggestions, everyone! I took a few hours to experiment last night and I believe I have achieved a satisfactory solution, which I will now describe.

First, here are some...
04-15-11, 03:24 AM
Replies: 21
Views: 6,233
Posted By Sander Saares

Sharp cutoff high-power LED lenses

I have installed a custom lighting solution with two high-power LEDs onto my bicycle, but after doing some final positioning adjustments, I ran into a small problem.

Namely, oncoming traffic gets...
10-08-10, 05:14 AM
Replies: 14
Views: 858
Posted By Sander Saares

The best guide I've seen was this:...

The best guide I've seen was this: http://www.troubleshooters.com/bicycles/wheelbuilding/index.htm
Far more detailed & thorough than the one on sheldonbrown.com.

I've only built one wheel but I...
09-06-10, 06:31 AM
Replies: 9
Views: 764
Posted By Sander Saares

Thanks again for all your help! The parts arrived...

Thanks again for all your help! The parts arrived in August and fit perfectly. I laced it up myself. The third set of spokes took three tries to get right but it still went better than I expected....
09-06-10, 06:25 AM
Replies: 13
Views: 6,559
Posted By Sander Saares

I just tighten a rag around the chain and spin...

I just tighten a rag around the chain and spin the crank for about a minute. Basically, take off as much as possible. As flim said, the lube should not be on the outside, so if you CAN remove it, do.
09-01-10, 06:02 AM
Replies: 7
Views: 3,242
Posted By Sander Saares

I found that this web site outlines the whole...

I found that this web site outlines the whole process even better than sheldownbrown.com: http://www.troubleshooters.com/bicycles/wheelbuilding/index.htm
07-24-10, 05:22 AM
Replies: 9
Views: 764
Posted By Sander Saares

Alright, thanks for the clarification. ...

Alright, thanks for the clarification.

Hmm... I'll ask DT Swiss why the 280-282 mm range is not available in any online shop I can see. Maybe they do not even manufacture them in this size? Let's...
07-23-10, 10:19 AM
Replies: 9
Views: 764
Posted By Sander Saares

Thanks! However, I am running into a strange...

Thanks! However, I am running into a strange difference between two spoke calculators.

Using the table you provided, I enter the data (24, 4, 590) and go to the closest matching hubs (d=58 and...
07-22-10, 10:33 AM
Replies: 9
Views: 764
Posted By Sander Saares

Many thanks! This website seems to say ERD...

Many thanks!

This website seems to say ERD is 590mm: http://www.halorims.com/halo/products-details.php?id=RMHA7W2B
The spoke counts seen there are lower but the wheel is still the same size,...
07-21-10, 11:12 PM
Replies: 9
Views: 764
Posted By Sander Saares

Spokes - how do I calculate length and which pattern?

I am in the process of getting a new rear wheel. The rim and hub have been ordered but I am a bit stuck at spokes - I am not sure how to calculate the required length. I am also unsure of the...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.