Bike Forums - Search Results

Go Back  Bike Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: miamijim
Showing results 1 to 19 of 19
Search took 0.02 seconds.
01-29-20, 06:41 PM
Replies: 3
Views: 275
Posted By miamijim

FT Bologna possibly made by OMAS ...

FT Bologna possibly made by OMAS

VeloBase.com - Component: FT Extra Rolling (http://velobase.com/ViewComponent.aspx?ID=8fc75ff9-1954-4d01-ba6a-8fb9efaf158e&Enum=110)
11-22-19, 09:29 AM
Replies: 74
Views: 5,009
Posted By miamijim

There's a little truth to what he says. If a...

There's a little truth to what he says.

If a chain and cassette/freewheel are gunked up the gunk/dirt/grease/grime/oil takes up a tick small amount of space between the link/rollers/pins. Think...
11-21-19, 02:08 PM
Replies: 46
Views: 4,842
Posted By miamijim

1. "This is a used part, therefore, it is only...

1. "This is a used part, therefore, it is only reasonable to expect wide variety, nicks, scratches and other imperfections. The pictures provided very clearly depict the overall condition.

2. ...
11-21-19, 11:35 AM
Replies: 46
Views: 4,842
Posted By miamijim

Eh. Everyone starts out at a (0) rating and ebay...

Eh. Everyone starts out at a (0) rating and ebay only lets you go down to like a -1 so why bother. I do FREE shipping to Continental U.S. International depends on the item. Sometimes its a pain...
11-19-19, 02:01 PM
Replies: 59
Views: 3,965
Posted By miamijim

Sometimes that's a hassle. I don't have any...

Sometimes that's a hassle. I don't have any spare hubs, no wooden dowels etc.

I don't bother to block them anymore. Again, I'll update my 'how to pack a frame 101' thread with my revised...
11-19-19, 09:12 AM
Replies: 59
Views: 3,965
Posted By miamijim

I had this exact conversation with the owner. If...

I had this exact conversation with the owner. If one were to cut off the lower section how different would it be from a vertical dropout? Differences for sure but what does the lower portion really...
11-18-19, 07:36 AM
Replies: 59
Views: 3,965
Posted By miamijim

Haha...wish I could take the credit. A lot of it...

Haha...wish I could take the credit. A lot of it came directly from this thread, I was just an intermediary as the frames 1,000 miles away. I really like the '2 axle technique'. As a side note,...
10-30-19, 04:31 PM
Replies: 79
Views: 8,972
Posted By miamijim

Prologue with Tange Prestige

Prologue with Tange Prestige
10-28-19, 07:45 PM
Replies: 59
Views: 3,965
Posted By miamijim

Great advice and in-line with how I've done them...

Great advice and in-line with how I've done them in the past. This is being done 'remotely' but I think we'll get it worked out. Definitely will add heat to the mix. Back in the day I'd hook the...
10-09-19, 06:11 PM
Replies: 55
Views: 2,078
Posted By miamijim

Alternate installation...start the adjusting cup...

Alternate installation...start the adjusting cup then install cartridge. Go back and forth but make sure the cartridge fully seats before the adjusting cup.

Sometimes cartridges will hit an...
05-23-19, 08:30 PM
Replies: 26
Views: 4,325
Posted By miamijim

Function of the 2 concave washers is firm a type...

Function of the 2 concave washers is firm a type of ‘spring’ to keep the system from loosening up.

Anyone who knows me knows I’m not a fan of Campy dt indexing levers. That plastic insert, if I...
04-10-18, 06:32 AM
Replies: 51
Views: 6,018
Posted By miamijim

Yes. But, some have a rubber ring seal on the...

Yes. But, some have a rubber ring seal on the backside. Those models will NOT flush well unless the rubber seal is removed. Simply flick it out with a pick and then reinstall when your done.
04-10-18, 05:26 AM
Replies: 51
Views: 6,018
Posted By miamijim

I've pulled freehub bodies part and highly...

I've pulled freehub bodies part and highly suggest NOT to. Flush, spin, flush, spin and repeat until the effluent isn't dirty. Lub, spin, lub, spin repeat until the effluent isn't dirty.
02-06-18, 06:49 AM
Replies: 51
Views: 6,018
Posted By miamijim

That tool wont do much of anything different than...

That tool wont do much of anything different than an in situ repair as mentioned earlier. The only reason to remove the freehub is because it needs replacement or your going to swap it to another...
06-10-15, 01:50 PM
Replies: 15
Views: 1,024
Posted By miamijim

Stay away from anything 9s. Very good value...

Stay away from anything 9s.

Very good value can be found in both Shimano and Campagnolo 10s groups.

Everything is going 11s so if you go that route it's likely you'll be outdated anytime soon.
11-14-11, 05:46 AM
Replies: 33
Views: 13,987
Posted By miamijim

'N' is Peugeot speak for clincher tires ...

'N' is Peugeot speak for clincher tires

82-83 PSV10 with tubulars. Normal seat post pinch bolts. French/Swiss threading.

84 there were 2 models PSV10N with clinchers and PSV10L with tublars. ...
Replies: 24
Views: 3,085
Posted By miamijim

It depends on your market. I've seen local...

It depends on your market. I've seen local flippers buy and re-sell the same bike on CL the very same day!!!

Do you plan on refurbishing them first or do you plan to simply re-list them with...
07-09-09, 04:27 PM
Replies: 57,358
Views: 8,320,634
Posted By miamijim

U-Haul or a Home Depot truck.

U-Haul or a Home Depot truck.
03-07-09, 08:27 AM
Replies: 80
Views: 23,901
Posted By miamijim

My schematic breakdown is slightly different than...

My schematic breakdown is slightly different than the OP's. It appears my levers are missing 1 thin washer and the lock washers under the outer bolts. My lever are a different version of the OP's...
Showing results 1 to 19 of 19


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright © 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.