Removing braze-ons from alloy frame...
#1
Senior Member
Thread Starter
Join Date: May 2005
Location: Albany, WA
Posts: 7,393
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 321 Post(s)
Likes: 0
Liked 7 Times
in
6 Posts
Removing braze-ons from alloy frame...
I am building a singlespeed from an old Giant hybrid bike, the cable guides on the top of the top tube are these ugly chunky triple beasts, I want to lose them but am afraid to trash the frame. Filing them off is not so hot since they are big buggers, it will take forever, and one slip of the file... and no, I don't have a Dremel and don't plan to buy one. They cost more than a new bike here in Oz.
Can I use heat? It looks like they are either brazed or soldered on.
Can I use heat? It looks like they are either brazed or soldered on.
#2
LF for the accentdeprived
Join Date: May 2005
Location: Budapest, Hungary
Posts: 3,549
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Aluminium or steel frame? Heat is not an option for Al.
I sawed mine off and then used a file to remove the remining material. Sawing takes 5-10 mins with a good handsaw, filing takes 30 or so with a decent file. Of course, half the time is spent looking at the frame sideways to see where the actual tube starts. Being inexperienced with powertools, I wouldn't have liked to risk my frame trying to use one.
Ok, those times are for one single cable stop, but you can do the two triples in an afternoon for sure.
I sawed mine off and then used a file to remove the remining material. Sawing takes 5-10 mins with a good handsaw, filing takes 30 or so with a decent file. Of course, half the time is spent looking at the frame sideways to see where the actual tube starts. Being inexperienced with powertools, I wouldn't have liked to risk my frame trying to use one.
Ok, those times are for one single cable stop, but you can do the two triples in an afternoon for sure.
#3
biff-o-matic
Join Date: Nov 2003
Location: Austin, TX
Posts: 305
Bikes: Moyer Cycles #1 - A fixie of course.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Since it's an aluminum frame, the 'braze-on' is either epoxied or riveted on.
If it's riveted, you can just drill out the rivet. Pretty simple.
If it's epoxied, I would go with a file, and be very, very careful. It won't take you forever, 15 mins per guide tops. Don't use a power tool because one slip of something like that and you'll be tearing through your coke can.
If it's riveted, you can just drill out the rivet. Pretty simple.
If it's epoxied, I would go with a file, and be very, very careful. It won't take you forever, 15 mins per guide tops. Don't use a power tool because one slip of something like that and you'll be tearing through your coke can.
#4
Matthew Grimm / Flunky
Join Date: Jan 2005
Posts: 656
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Originally Posted by jur
Can I use heat? It looks like they are either brazed or soldered on.
Then use some sandpaper wrapped around the tube to finish. Wrapping the sandpaper will preclude you from making flat spots on the tube. Start w/ coarse and work to fine. When you do this, motion is like doing a shoeshine buff.
Practice on a crap frame until you get confident.
#5
Senior Member
Thread Starter
Join Date: May 2005
Location: Albany, WA
Posts: 7,393
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 321 Post(s)
Likes: 0
Liked 7 Times
in
6 Posts
Originally Posted by Kogswell
Use a light hack saw blade to cut them off. Wrap the surrounding tube w/ duct tape to avoid scaring. Make a couple of cuts if you have to.
Then use some sandpaper wrapped around the tube to finish. Wrapping the sandpaper will preclude you from making flat spots on the tube. Start w/ coarse and work to fine. When you do this, motion is like doing a shoeshine buff.
Practice on a crap frame until you get confident.
Then use some sandpaper wrapped around the tube to finish. Wrapping the sandpaper will preclude you from making flat spots on the tube. Start w/ coarse and work to fine. When you do this, motion is like doing a shoeshine buff.
Practice on a crap frame until you get confident.
I was hoping to save some of the cable guides because I will need to attach 2 for the rear brake cable. Any advice on that?
Heh, after looking at some of the pics posted in the pics thread, this frame probably IS a crap frame...
#6
Bikes are Fun
Join Date: Jan 2005
Posts: 187
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
sometimes you can just get a pair of beefy pliers, get a hood hold on the braze, and twist. you can get it off that way and then file the rest. ive only done this method with steel so i cant gauruntee itll work. you could also see if you could score a dremel, from someone/where. its super easy like that and you can cut cautiosly then file the rest.
#8
))<>((
Join Date: Jul 2005
Location: Mpls
Posts: 108
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Originally Posted by honduraz10
sometimes you can just get a pair of beefy pliers, get a hood hold on the braze, and twist. you can get it off that way and then file the rest.