Old cog
#1
liar
Thread Starter
Join Date: Jan 2008
Location: MONTREAL
Posts: 220
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Old cog
My gf and I are changing her drivetrain and installing a use (by me) Miche cog whose teeth are just beginning to get a little wave-like. My question is: should I put the cog on backwards? For those not familliar with Miche cogs, they come in 2 pieces, see here:
I'm wondering will this give us some more life out of it or will it simply wear throught her chain quicker? will there be other problems I'm not anticipating?
ps. Miche cogs suck and you should avoid them. The amount of play between cog and carrier is ridiculous.
I'm wondering will this give us some more life out of it or will it simply wear throught her chain quicker? will there be other problems I'm not anticipating?
ps. Miche cogs suck and you should avoid them. The amount of play between cog and carrier is ridiculous.
#2
Senior Member
Funny, there is absolutely no detectible play between my Miche cogs and carrier when the lockring is installed. Make sure your lockring is properly tightened with a lockring wrench. You are probably feeling play in the chain, not the cog/carrier interface. I've never considered turning one around backwards, but if it fits onto the carrier backwards (I've never tried) there's no reason not to try it. It would be no different than flipping a chainring to get some more use out of it.
Last edited by mihlbach; 02-15-08 at 12:51 PM.
#3
Senior Member
Join Date: Aug 2007
Posts: 242
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
just what i was going to say, you probably just feel play in your chain, or you dont have your lockring tightened properly. I've never felt play with my cog system.
#4
liar
Thread Starter
Join Date: Jan 2008
Location: MONTREAL
Posts: 220
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
^This doesn't answer my question. My cog and lockring are properly installed. I was just noting how the 0.5mm or so of play between the two produces uncircularity way beyond the tolerances of any other cog. This hasn't been problematic for me, I just find that it introduces an imperfection where there needn't be any.
What I was asking was wether flipping my cog around was a sound way to get more life out of it.
Thx
What I was asking was wether flipping my cog around was a sound way to get more life out of it.
Thx
#5
Senior Member
If the cog is worn, its probable that your chain is stretched (worn) as well. A worn chain will probably not run smoothly with the cog flipped, for the same reason a new cog may not run smoothly with a worn chain. If you flip the cog and use a new chain, it will be basically the same as running a new chain and new cog. When you packpedal, you will still be engaging the chain against the worn side of the cog teeth, but I doubt that really matters much unless you regularly ride your bike backwards for miles and miles.
Yes, in theory, flipping your cog will essentially double its life, as long as you replace the chain when you flip it.
Yes, in theory, flipping your cog will essentially double its life, as long as you replace the chain when you flip it.
Last edited by mihlbach; 02-15-08 at 01:25 PM.
#7
stay free.
Join Date: Dec 2007
Location: Ellensburg, WA
Posts: 1,557
Bikes: EAI Bare Knuckle, 1980's Ross Signature 292s 12 speed
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Spend 18 dollars on a beefy surly cog and 10 bucks on a decent lockring. Thats what I would do at least, specially if it was on my ladies whip.