Go Back  Bike Forums > Bike Forums > Singlespeed & Fixed Gear
Reload this Page >

Bolt of the front brake is too long for my Pista fork. Help!

Notices
Singlespeed & Fixed Gear "I still feel that variable gears are only for people over forty-five. Isn't it better to triumph by the strength of your muscles than by the artifice of a derailer? We are getting soft...As for me, give me a fixed gear!"-- Henri Desgrange (31 January 1865 - 16 August 1940)

Bolt of the front brake is too long for my Pista fork. Help!

Old 06-28-07, 08:15 PM
  #1  
big ring
Thread Starter
 
MIN's Avatar
 
Join Date: Mar 2007
Location: philadelphia
Posts: 5,838
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Bolt of the front brake is too long for my Pista fork. Help!

I'm building up my new Pista and attempting to install the front brakes. Unluckily for me, the bolt that holds the brake on to the fork (the 5mm allen) is too long. I compared against my road bike, which has a carbon fork and the roadie has a thicker cross section. So the brakes I bought doesn't fit on the Pista's fork (the chrome unicrown fork.)

Here is a photo for reference - not mine.



The brakes I tried were $30 Shimano 550s. Suggestions for another brake caliper or alternate installation options?

thanks.
MIN is offline  
Old 06-28-07, 08:35 PM
  #2  
FG 48x17
 
eaglevii's Avatar
 
Join Date: Jan 2006
Location: El 'Burque, NM
Posts: 289

Bikes: Lemond Road, IRO Rob Roy, Rush Hour Fixie

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
It is unlikely that the bolt itself (the threaded rod attached to the brake caliper) is too long. If the nut is too long, you can go to an LBS and ask for a shorter nut - multiple sizes are available. Rear brake nuts tend to be pretty short. If the bolt itself is too long, you could risk cutting it shorter (it may take some working to get the threads right after cutting (getting an M6 x 1.0 nut from a hardware store may help you get the threads working without ruining your brake nut). If your fork is really, really narrow, I guess you could use a long nut and a rear brake (which would have a very short bolt).
eaglevii is offline  
Old 06-28-07, 08:38 PM
  #3  
big ring
Thread Starter
 
MIN's Avatar
 
Join Date: Mar 2007
Location: philadelphia
Posts: 5,838
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Originally Posted by eaglevii
It is unlikely that the bolt itself (the threaded rod attached to the brake caliper) is too long. If the nut is too long, you can go to an LBS and ask for a shorter nut - multiple sizes are available. Rear brake nuts tend to be pretty short. If the bolt itself is too long, you could risk cutting it shorter (it may take some working to get the threads right after cutting (getting an M6 x 1.0 nut from a hardware store may help you get the threads working without ruining your brake nut). If your fork is really, really narrow, I guess you could use a long nut and a rear brake (which would have a very short bolt).
Great, you are on the same page as me.

LBS guys gave me a rear unit the first time by accident. So I know that is actually too short for the fork.

Are these nuts pretty universal then? I can simply go and ask for a shorter nut?
MIN is offline  
Old 06-28-07, 08:39 PM
  #4  
fails just as quickly
 
thequickfix's Avatar
 
Join Date: Apr 2006
Location: two miles behind
Posts: 522
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Washers on the front of the fork.
thequickfix is offline  
Old 06-28-07, 08:43 PM
  #5  
big ring
Thread Starter
 
MIN's Avatar
 
Join Date: Mar 2007
Location: philadelphia
Posts: 5,838
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Originally Posted by thequickfix
Washers on the front of the fork.
Not sure about that idea; that would generate to much torque on brake when braking. I would like to keep the distance between the brake and the fork the same.
MIN is offline  
Old 06-28-07, 08:57 PM
  #6  
FG 48x17
 
eaglevii's Avatar
 
Join Date: Jan 2006
Location: El 'Burque, NM
Posts: 289

Bikes: Lemond Road, IRO Rob Roy, Rush Hour Fixie

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
As far as I know, all recent road brakes have the same threading, but just bring the caliper with you to make sure. You can always add a washer or two to the back of the fork if need be...
eaglevii is offline  
Old 06-28-07, 11:42 PM
  #7  
fails just as quickly
 
thequickfix's Avatar
 
Join Date: Apr 2006
Location: two miles behind
Posts: 522
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Originally Posted by min
Not sure about that idea; that would generate to much torque on brake when braking. I would like to keep the distance between the brake and the fork the same.
Torque? Are you saying that moving the caliper farther out from the fork crown will make a longer lever arm in the form of the fixing bolt pivoting against the front of the fork crown? It seems to me that the force acting on the caliper while braking would be nearly parallel with the fixing bolt. Perhaps I am misunderstanding your problem, but moving the caliper out a couple of millimeters is not a problem.
thequickfix is offline  
Old 06-29-07, 12:36 AM
  #8  
raodmaster shaman
 
Join Date: Dec 2004
Location: G-ville
Posts: 1,431
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by MIN
Not sure about that idea; that would generate to much torque on brake when braking. I would like to keep the distance between the brake and the fork the same.

edited for my bad description.

there is little force perpendicular to the length of the bolt (up and down), so changing that length will not change the torque since there isnt realy one to begin with.

some sort of a washer/spacer is pretty standard on most brake set-ups, and may be easier than a new nut.

Last edited by roadgator; 06-29-07 at 12:43 AM.
roadgator is offline  
Old 06-29-07, 03:19 AM
  #9  
Senior Member
 
BoozyMcliverRot's Avatar
 
Join Date: Jan 2007
Location: bradenton FL
Posts: 1,240

Bikes: 1991 Diamondback Master TG 1990 Trek 850 Antelope

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 117 Post(s)
Liked 325 Times in 106 Posts
Spacers.......10 for a dollar at any hardware store.
BoozyMcliverRot is offline  
Old 06-29-07, 12:15 PM
  #10  
FG 48x17
 
eaglevii's Avatar
 
Join Date: Jan 2006
Location: El 'Burque, NM
Posts: 289

Bikes: Lemond Road, IRO Rob Roy, Rush Hour Fixie

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Like I said before, if you are concerned about the physics, but the spacers in the back.
eaglevii is offline  
Old 06-29-07, 12:23 PM
  #11  
Member
 
Join Date: Apr 2006
Posts: 39
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I had the same situation--a Pista and a 500Ex brake and put a washer (can't remember how thick--probably a millimetre or two) behind the fork crown. Worked just fine, and it was only slightly unsightly.
atelierf.lab is offline  
Old 06-29-07, 12:27 PM
  #12  
blah
 
onetwentyeight's Avatar
 
Join Date: Oct 2005
Location: Oakland, CA
Posts: 5,573
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 5 Times in 3 Posts
hacksaws can do all sorts of amazing things. or go to your lbs and get the correct length parts.
onetwentyeight is offline  
Old 06-29-07, 12:30 PM
  #13  
big ring
Thread Starter
 
MIN's Avatar
 
Join Date: Mar 2007
Location: philadelphia
Posts: 5,838
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 1 Time in 1 Post
UPDATE.

I used a chain ring spacer (10mm deep) around the brake bolt. This was in the back of the fork so the brake is still right up against the fork. Thanks for the great suggestions... I don't know why I didn't think of that.
MIN is offline  
Old 06-29-07, 12:35 PM
  #14  
Banned
 
Join Date: May 2005
Location: GA
Posts: 5,317
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
you could also have just cut the nut shorter.
dutret is offline  
Old 06-29-07, 12:40 PM
  #15  
Member
 
Join Date: Apr 2006
Posts: 39
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I always approach nut-cutting with some trepidation.
atelierf.lab is offline  
Old 08-05-08, 09:19 PM
  #16  
Senior Member
 
Join Date: Apr 2006
Posts: 305
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
This proved quite helpful as I experienced the same problem on my 08 Pista with a set of 105 9-speed front brake calipers. Using a washer solved the problem for me. You'd think these kind of minor problems would be something they'd fix on newer models, that and the rather unconventional 1" threadless fork.
legstwelve is offline  
Old 08-05-08, 09:23 PM
  #17  
Senior Member
 
cjump's Avatar
 
Join Date: Jul 2008
Location: North Carolina
Posts: 276

Bikes: A few Scotts

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by atelierf.lab
I always approach nut-cutting with some trepidation.
as does jesse jackson
cjump is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.