Gear help for single speed centuries
#1
Senior Member
Thread Starter
Join Date: Dec 2010
Location: Ann Arbor, MI
Posts: 222
Bikes: 2010 Niner EMD, 2008 Surly Steamroller, 2007 Giant OCR.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Gear help for single speed centuries
Hey folks, I don't normally post in this forum even though I do ride fixed/single all the time. Nice to meet you all and sorry for posting the redundant topic of gearing.
Every summer I partake in the WAM 300, its a 3-day road event, 100 miles a day, from Traverse City to Chelsea, MI. I'm hoping to do it single-speed next year, and want some advice on gearing. What is a good gearing for long distance riding? The first 100 are pretty hilly, the second and third 100 are rolling with some long, flat, fast stretches.
I've never set this bike up for road cycling - only fixed and cyclocross. I'm kind of out in the dark on this, and would rather not pay for 3 chainrings just to try out different gearings, if it can be avoided. What do you guys think?
Every summer I partake in the WAM 300, its a 3-day road event, 100 miles a day, from Traverse City to Chelsea, MI. I'm hoping to do it single-speed next year, and want some advice on gearing. What is a good gearing for long distance riding? The first 100 are pretty hilly, the second and third 100 are rolling with some long, flat, fast stretches.
I've never set this bike up for road cycling - only fixed and cyclocross. I'm kind of out in the dark on this, and would rather not pay for 3 chainrings just to try out different gearings, if it can be avoided. What do you guys think?
#2
Goes to 11.
Join Date: Oct 2010
Location: Wichita, KS, USA
Posts: 2,547
Bikes: 2015 Soma Double Cross
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I'd do a flip-flop hub with a freewheel on each side. Something like 65GI for the flats, and 45GI for the hills. You can accomplish that with a 39t chainring, and 16t and 22t freewheels. With such a large difference in tooth count between the two freewheels, you'll probably need to lengthen your chain when you get to the flatter part of the ride.
People with different levels of fitness will likely have different opinions regarding gear choices, and they'll all be right.
People with different levels of fitness will likely have different opinions regarding gear choices, and they'll all be right.
#4
Senior Member
Thread Starter
Join Date: Dec 2010
Location: Ann Arbor, MI
Posts: 222
Bikes: 2010 Niner EMD, 2008 Surly Steamroller, 2007 Giant OCR.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Same here. However I do this ride with a couple older guys who, while extremely fit for their age and biking experience, aren't pushing me much. I'm looking for a way to challenge myself a bit while making it easier to stay with them instead of pulling ahead. I think doing it single could be a lot of fun - also my steel single speed (Surly Steamroller) is a lot more fun and comfortable to ride than my lightweight aluminum race bike. Maybe I will end up doing it geared, but I'm putting serious thought into not.
#6
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,784
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3587 Post(s)
Liked 3,400 Times
in
1,934 Posts
#7
Goes to 11.
Join Date: Oct 2010
Location: Wichita, KS, USA
Posts: 2,547
Bikes: 2015 Soma Double Cross
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#8
Senior Member
Thread Starter
Join Date: Dec 2010
Location: Ann Arbor, MI
Posts: 222
Bikes: 2010 Niner EMD, 2008 Surly Steamroller, 2007 Giant OCR.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
am I in the right forum?
#9
Senior Member
Join Date: Jul 2009
Posts: 206
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I've ridden two fixed centuries now. The route I've taken has been the same both ways--the gateway trail out of MPLS/St. Paul to some state park down a highway to Stillwater and back, then riding part of the Grand Rounds in the TC to make it 100 even; if you really want to know elevation changes holler and I'll google it for you, but I can tell you that the gateway is pretty flat (and thats probably 25-30 miles), the highway into Stillwater is rolling hills, and the hills out of Stillwater (we take a different highway out to meet the gateway) aren't terribly long but require some mashing. I didn't bother to change my gearing at all. On my first ride I set out fixed as a sort of personal challenge to see if I could do it, figuring I'd flip to my freewheel if I couldn't handle it. The rabbit gear calculator has me at 70.3 gi, 48/18. That gets you to 16.7mph at 80 rpms (and I was surprised to apparently be doing that on the way into Stillwater, so sayeth the speed limit, "you're going this fast" sign), and up to 20.9 at 100. I don't know that you'll be maintaining 100 rpms for any extended period, but I'm pretty ill-experienced with longer rides, and maybe your fitness level blows mine out of the water. If you're doing fw/fw on a flip flop hub, why not start there and drop down to 60-65 gi for the hilly rides if they're really bad? Or adjust up if you're substantially more fit than me and know what kind of mph you push based on a given gear ratio?
P.S. This was riding with a friend who rides substantially less than me, so a pretty lackadaisical pace. I pulled ahead of him at times for funzies, but ultimately wanted to hang back with him. If you're going more uptempo with your friends, you can definitely go higher than that.
P.S. This was riding with a friend who rides substantially less than me, so a pretty lackadaisical pace. I pulled ahead of him at times for funzies, but ultimately wanted to hang back with him. If you're going more uptempo with your friends, you can definitely go higher than that.
#10
Senior Member
Join Date: Dec 2006
Posts: 3,693
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Mid 60s to low 70s would work for me. I think 70 is a good place to start. 100 miles a day three days in a row is enough to make you want to take it easy. The gear you can push for a 50 mile one day road ride is pretty different than what you want for this ride.
80 GI sounds insane to me, much like most of the gearing people say works for em on this forum. But hey, everyone is different. You've got to try out a few combos on shorter rides first.
80 GI sounds insane to me, much like most of the gearing people say works for em on this forum. But hey, everyone is different. You've got to try out a few combos on shorter rides first.
#11
TEEEJ
Join Date: May 2011
Location: Minneapolis, MN
Posts: 114
Bikes: 78.5 Trek 710 FG Conversion, 90's Raleigh CitySport FG coversion, '98 Specialized Ground Control, '00 GT Outpost SS, Vilano Track Bike
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I do 48/16 for centuries, mostly rolling hills with a couple good climbs, its mostly preference
#12
Senior Member
Thread Starter
Join Date: Dec 2010
Location: Ann Arbor, MI
Posts: 222
Bikes: 2010 Niner EMD, 2008 Surly Steamroller, 2007 Giant OCR.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
M_S and tjemitchell27, thank you very much for your input as well.
#13
Your cog is slipping.
I should have elaborated. My main reason for gearing up is because I've found that excessive spinning on long rides like that tends to wear me out and I'd rather be able to maintain a good speed to cover more miles, even if it means having to work a little harder to do so.
#14
Fresh Garbage
Since you have until summer I dont think you have much to worry about. While training on a single speed you will find which gears work for you. The longest I have gone on a fixed ride was about 70 miles with some rollers at 48/19 (I can only guess ~18mph average)and I was really spinning along. Others seem to prefer higher all-around gears to help conserve. I guess I am repeating what the others have said - find what's comfortable. But, if you can train yourself to keep up with a low gear you will have an easier time with changes in terrain. plus, if you bonk you wont be stuck on a hard gear
Last edited by hairnet; 11-25-11 at 11:54 PM.
#15
Happy go lucky
Join Date: Aug 2011
Location: Illinois
Posts: 286
Bikes: 2010 Nagasawa (Track), EAI Bareknuckle (Track), Custom Jonny Cycles (Track), 90's Eddy Merckx (Road), 2002 Colnago Tecnos, 200? Felt F60 (Road), 1992 Schwinn Paramount Series 3 (Road)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I've ridden two or three fixed centuries in Traverse City that were VERY hilly. It's far from flat out there guys. Most people wouldn't make it through a century there with ~80 gear inches. You have an advantage riding SS in that you can coast down the mountains.
What do you use today when you ride SS? Do you consider yourself a spinner? Are you a strong rider compared to most or are you fairly casual? Will you be sucking someones tail at all or will it be mostly solo?
My gearing for that area was the basic 42x16 but that was only 100 miles in one day (not 300 over 3 days!) and I probably had a friendly paceline for some of it. If you can't spin, then 70 gear inches is going to seem too short with a draft. But you'll appreciate it when laboring for 20 minutes up a hill. You'll be able to actually pedal and put some power into it going downhills (as fast as it may be).
If you're going to be a part of a paceline, I would gear so that my comfortable spinning pace is at about 20 mph (or whatever speed your paceline is on the flats). Chances are that'll put you in the 70 to 75 range. I would try REALLY hard to stick to the 70 side of things. Even going as low as 68 on that first day. For days two and three you should gear up.
TL;DR
Day 1: Run about 70 gear inches (lower or higher depending on your strength and whether you're doing it solo or not). Warning: You will be seriously laboring up a few of the hills depending on where the ride goes (as in one complete pedal rotation every few seconds).
Day 2: Run something taller, like 74 to 76 (assuming there's no major climbs, just rolling hills)
Day 3: Listen to your legs
What do you use today when you ride SS? Do you consider yourself a spinner? Are you a strong rider compared to most or are you fairly casual? Will you be sucking someones tail at all or will it be mostly solo?
My gearing for that area was the basic 42x16 but that was only 100 miles in one day (not 300 over 3 days!) and I probably had a friendly paceline for some of it. If you can't spin, then 70 gear inches is going to seem too short with a draft. But you'll appreciate it when laboring for 20 minutes up a hill. You'll be able to actually pedal and put some power into it going downhills (as fast as it may be).
If you're going to be a part of a paceline, I would gear so that my comfortable spinning pace is at about 20 mph (or whatever speed your paceline is on the flats). Chances are that'll put you in the 70 to 75 range. I would try REALLY hard to stick to the 70 side of things. Even going as low as 68 on that first day. For days two and three you should gear up.
TL;DR
Day 1: Run about 70 gear inches (lower or higher depending on your strength and whether you're doing it solo or not). Warning: You will be seriously laboring up a few of the hills depending on where the ride goes (as in one complete pedal rotation every few seconds).
Day 2: Run something taller, like 74 to 76 (assuming there's no major climbs, just rolling hills)
Day 3: Listen to your legs
Last edited by trevor_ash; 11-26-11 at 12:41 AM.
#16
Senior Member
Join Date: Dec 2006
Posts: 3,693
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I should have elaborated. My main reason for gearing up is because I've found that excessive spinning on long rides like that tends to wear me out and I'd rather be able to maintain a good speed to cover more miles, even if it means having to work a little harder to do so.
Anyways, it is mashing a big gear that really wears me out rather than spinning, so it is interesting to hear your experience. For me I am noticeably less worn out in everything from SS cross racing to mountain biking to longer road rides if I consciously choose a gear on the low end of what I feel is an appropriate range. BUT my strong point is aerobic capacity more than leg strength, so maybe that explains why we have found that the opposite works for each of us. Like I said, everyone is different. Just because it sounds crazy to me doesn't make it wrong... maybe it makes it right.
#17
Senior Member
Join Date: Jul 2002
Location: Sacramento, California, USA
Posts: 40,865
Bikes: Specialized Tarmac, Canyon Exceed, Specialized Transition, Ellsworth Roots, Ridley Excalibur
Mentioned: 68 Post(s)
Tagged: 0 Thread(s)
Quoted: 2952 Post(s)
Liked 3,106 Times
in
1,417 Posts
I also vote for low 70's as a starting point. Adjust as comfort requires.
#18
sɹɐʇsɟoןןnɟsʇıbɟɯo
Join Date: Oct 2010
Location: seattle, too many links
Posts: 3,986
Bikes: fixed gear recumbent trike
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
i think its really personal, some ppl can spin longer and others are better at mashing...
i've done several fixed centuries, with 66.6 GI and 77 GI.
i have way felt better during/after with the 66.6 (48x19) than with the 77 (48x17)
altho, i was way faster with the bigger gear ratio (at least 1.5hrs faster (but i was on a tear that day))
i've done several fixed centuries, with 66.6 GI and 77 GI.
i have way felt better during/after with the 66.6 (48x19) than with the 77 (48x17)
altho, i was way faster with the bigger gear ratio (at least 1.5hrs faster (but i was on a tear that day))
#19
Senior Member
Join Date: Apr 2005
Location: Brownsville, TX
Posts: 2,174
Bikes: Surly CC
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
White Industries double/double or dos freewheel cog? Wouldn't have to fuss too much with chain adjustments (both supposedly are adapted to deal with the same chain length) but it would give you the hill variable+flats.
#20
Senior Member
I have found that 76ish is a good generic gear for me for just about any distance. I can climb with it and hold a fairly high speed without excessive spinning. When riding with fast roadies and/ or flat terrain I will bump it up to the low 80s. Any lower and the excessive spinning gets annoying and tiring. Any higher is good for sprinting, but more fatiguing during long distances.
#21
Senior Member
Thread Starter
Join Date: Dec 2010
Location: Ann Arbor, MI
Posts: 222
Bikes: 2010 Niner EMD, 2008 Surly Steamroller, 2007 Giant OCR.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Ok, thanks for the advice everyone. Guess I'll just have to bite the bullet and try out a couple different combinations. The White Industries double freewheel sounds like a good idea if I need it, a bit pricey though! I'll start around 70-75ish (hopefully can hobble something together from parts laying around just to see how it works out) and go from there. Thanks again.
#22
Happy go lucky
Join Date: Aug 2011
Location: Illinois
Posts: 286
Bikes: 2010 Nagasawa (Track), EAI Bareknuckle (Track), Custom Jonny Cycles (Track), 90's Eddy Merckx (Road), 2002 Colnago Tecnos, 200? Felt F60 (Road), 1992 Schwinn Paramount Series 3 (Road)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Sounds good Alan. One thing you can try is figure out the ride, find the steepest hill, and then find something local that's about as steep and give it a shot.
#23
Senior Member
While i think this is a good idea, I wouldn't base your gearing decision one one hill unless that one hill constitutes a significant portion of the ride, or if there's a bunch of similar climbs. Base your gearing decision based on what you will be riding most of the time.
#24
Member
Join Date: May 2011
Posts: 49
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#25
Cat Enthusiast
Join Date: Aug 2011
Location: Plymouth, MI
Posts: 2,227
Bikes: All City Nature Boy
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts