Captain's pedals
#1
..
Thread Starter
Join Date: May 2005
Posts: 349
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Captain's pedals
It's my understanding (meaning I haven't removed them yet to verify) that both of the captain's pedals have left handed threads. If so, is there a source for pairs of pedals that have left handed threads? I want to put SPD's on my tandem but the idea of buying two pair and using just one pedal from each pair seems so wasteful.
#2
rebmeM roineS
Join Date: Jan 2006
Location: Metro Indy, IN
Posts: 16,216
Bikes: Bacchetta Giro A20, RANS V-Rex, RANS Screamer
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 653 Post(s)
Liked 347 Times
in
226 Posts
If the captain's crank is tandem-captain-specific, as it should have come from the factory, or been built up correctly, then the pedal threads on the crankarms, and the pedals, will be "normal". If the captain's crank is a flip-flopped single bike crank, then the pedal threads on both crankarms will be reversed from what they should be. And, loctite and diligence will be required. This is assuming that the synchornizer chain is on the left side.
#3
hors category
Join Date: Jan 2002
Posts: 7,231
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 5 Times
in
5 Posts
What year/make/model of tandem do you have and/or what make/model of cranks are on your tandem?
#4
Senior Member
Join Date: Jul 2006
Location: Buenos Aires, Argentina
Posts: 378
Bikes: Co-Motion Mocha, Trek T100, Schwinn Fastback Comp, Specialized Stumpjumper
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
If the peddals are on the bike see if you can find any labels on either the crank or the peddals to see which way the thread is going before you put a wrench to them, crank arms are usually marked L or R. I have mangled a thread on a crank arm by insisting on going the wrong way.
#5
..
Thread Starter
Join Date: May 2005
Posts: 349
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Thanks for all the replies.
The bike is a late 90's Univega mountain tandem. It's pretty low end but for the price (<100) it was hard to pass up. It only needed a stoker bar and saddle. It does have a left-side timing chain and it doesn't have any brand markings on any of the cranks. I'll have to look at the pedals closer and see if they have any thread markings. Now I'm getting excited. If they ARE standard threads, or even if they've just been flipped, I've got a pair of pedals ready to pop on.
The bike is a late 90's Univega mountain tandem. It's pretty low end but for the price (<100) it was hard to pass up. It only needed a stoker bar and saddle. It does have a left-side timing chain and it doesn't have any brand markings on any of the cranks. I'll have to look at the pedals closer and see if they have any thread markings. Now I'm getting excited. If they ARE standard threads, or even if they've just been flipped, I've got a pair of pedals ready to pop on.
#6
Year-round cyclist
Join Date: Apr 2002
Location: Montréal (Québec)
Posts: 3,023
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
You might look for a tiny L or R on the pedal. You might also look for marks on the crankarms that say "Tandem" or something similar. Another sure bet is that all the crank arms and chainrings will look like they come from the same molding.
Anyway, I'm 90% sure that they are low end maybe, but still the typical tandem crankset you have on modern tandems. Therefore each rider has a right pedal that is threaded the normal way and a left pedal which is left-threaded.
In other words, you'll need ONE set of (normal) pedals.
Anyway, I'm 90% sure that they are low end maybe, but still the typical tandem crankset you have on modern tandems. Therefore each rider has a right pedal that is threaded the normal way and a left pedal which is left-threaded.
In other words, you'll need ONE set of (normal) pedals.
#7
Senior Member
Join Date: Sep 2005
Location: New Orleans
Posts: 179
Bikes: Cannondale Road Tandem, Rodbikes Belt Drive Fixed Gear
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Sorry if this is obvious, but grab any set of pedals (maybe off of a different bike, or out of your parts bin) and see how they go on. This should make the situation clear.
As mentioned tandem cranks are reverse threaded (that is to say that if they were mounted with the chainring on the right, they would be reverse). When mounted on a tandem with the chainring on the left, everything is normal. You can you use any set of pedals and put them on the same way you would put them on anything.
As mentioned tandem cranks are reverse threaded (that is to say that if they were mounted with the chainring on the right, they would be reverse). When mounted on a tandem with the chainring on the left, everything is normal. You can you use any set of pedals and put them on the same way you would put them on anything.
#9
..
Thread Starter
Join Date: May 2005
Posts: 349
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I finally had the chance to go out and look. After scraping at the rust on the ends of the pedals I was rewarded with one R and one L. So this is good news. Interesting that everyone here was so confident there would be one left and one right. Got to see if I can find where I read that about them having two lefts....
Oh yeah, on the Blayleys site, https://www.blayleys.com/articles/tandem/index.htm
Well I'm glad they were wrong and you all were right. Thanks.
Oh yeah, on the Blayleys site, https://www.blayleys.com/articles/tandem/index.htm
Well I'm glad they were wrong and you all were right. Thanks.