unbolting bolt on crank arms.
07-01-11, 08:18 PM
#1
Junior Member
Thread Starter
Join Date: Feb 2011
Location: Central Massachusetts
Posts: 24
Bikes: 2003 GT i-drive 1.0. And looking for some classic pieces.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
unbolting bolt on crank arms.
I'm looking to unbolt the crank arms on my GT Idrive, but the bike shop loctited everything together. I'm just wondering if these bolts are right hand or left hand thread, or are the the same as the peddles right on right, left on left? Thanks.
07-01-11, 08:26 PM
#2
Senior Member
Join Date: Jul 2005
Location: Boulder County, CO
Posts: 4,396
Bikes: '80 Masi Gran Criterium, '12 Trek Madone, early '60s Frejus track
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 514 Post(s)
Liked 448 Times
in
337 Posts
Both crank arm bolts are standard (lefty-loosey) threaded. After you remove the bolts you will need a crank arm extractor to remove the crank arms. See the Park Tool web site for instructions on removing and re-installing crank arms.
07-01-11, 08:30 PM
#3
Insane Bicycle Mechanic
Join Date: Mar 2008
Location: other Vancouver
Posts: 9,839
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 805 Post(s)
Liked 707 Times
in
378 Posts
The bolts that hold on crankarms are right-hand thread. If they're on tight, count your blessings. Too-loose crank bolts will allow the crankarms to work loose, which ruins them.
FWIW: if you're going to take them off, you will probably also need a crankarm remover, like this: https://www.parktool.com/product/cran...-cranks-ccp-22 . There's a couple variations, so it would be nice to know what kind of cranks are on your bike. Also, when you put them back on, you'll want to torque them down properly- they should get 25 to 35 foot-pounds of torque. (See https://www.parktool.com/blog/repair-...s-and-concepts .) You can't do that very well with a little socket or hex (Allen) wrench.
FWIW: if you're going to take them off, you will probably also need a crankarm remover, like this: https://www.parktool.com/product/cran...-cranks-ccp-22 . There's a couple variations, so it would be nice to know what kind of cranks are on your bike. Also, when you put them back on, you'll want to torque them down properly- they should get 25 to 35 foot-pounds of torque. (See https://www.parktool.com/blog/repair-...s-and-concepts .) You can't do that very well with a little socket or hex (Allen) wrench.
__________________
Jeff Wills
Comcast nuked my web page. It will return soon..
Jeff Wills
Comcast nuked my web page. It will return soon..
07-02-11, 09:28 PM
#4
Senior Member
Join Date: May 2004
Location: Southern California
Posts: 2,191
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 114 Post(s)
Liked 119 Times
in
92 Posts
Using a threadlocking compound is unnecessary on a bicycle. If the fastener is torqued properly, it will be fine without any thread locker. In my experience, the crank arm bolts need about 30 ft-lb of installation torque (imagine a 30 lb weight hanging off a 1 foot wrench). And you'll need more than that to remove it. It's quite a bit of force, and I usually use automotive type wrenches to remove. You won't be able to remove with a multi-tool.
When you reinstall the bolt, grease the threads, to avoid sticking/corrosion in the future. And use of torque wrench is highly encouraged especially if you have square taper bottom bracket to crank arm interface. As Jeff pointed out, loose crankbolts is often a prelude to buying a new crank arms.
Also, you might want to wear gloves, so your skin doesn't meet the mean teeth of the chain ring when the bolt finally gives.
When you reinstall the bolt, grease the threads, to avoid sticking/corrosion in the future. And use of torque wrench is highly encouraged especially if you have square taper bottom bracket to crank arm interface. As Jeff pointed out, loose crankbolts is often a prelude to buying a new crank arms.
Also, you might want to wear gloves, so your skin doesn't meet the mean teeth of the chain ring when the bolt finally gives.
