Removing chainring bolts?
#1
Warehouse Monkey
Thread Starter
Join Date: Jul 2008
Location: Lebanon Co., Pennsylvania
Posts: 1,604
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 305 Post(s)
Likes: 0
Liked 7 Times
in
2 Posts
Removing chainring bolts?
I am changing the chainring on my new Kilo TT FG bike. Are there any tricks to holding the slotted nuts? I looked on youtube for ideas but nothing that has worked thus far. I see that Park Tool sells a wrench for this, but I would have to mail order one.
Any help?
Any help?
__________________
'10 Specialized Hardrock
'10 Specialized Hardrock
#2
Senior Member
You can use a flat head screwdriver to hold the nut(s) , other than that get the Park 's tool .
#3
Senior Member
Join Date: Apr 2008
Location: St. Pete, Florida
Posts: 1,258
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 83 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
I tried all kinds of improvised solutions the first time I tried this. Long story short, I had to buy the Park chainring nut tool. And even with the right tool it took a combination of finesse and force to get them loose.
#4
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,720
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5788 Post(s)
Liked 2,581 Times
in
1,431 Posts
I rarely need to hold the nuts. The trick is to loosen with a quick snapping action, which will pop the screw loose (doesn't always work). Once it's a bit loose you can usually hold the nut with direct thumb pressure. In a few cases where the thread may be sticky, especially if some shoemaker used locktite on the threads.
For installing and to prevent issues, you can use some lapping compound under the rim of the nut. This will effectively bind it to the ring and hold it while you tighten or loosen. If you prefer, locktite or a similar adhesive under the nut's rim does the same thing.
For installing and to prevent issues, you can use some lapping compound under the rim of the nut. This will effectively bind it to the ring and hold it while you tighten or loosen. If you prefer, locktite or a similar adhesive under the nut's rim does the same thing.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
#5
Senior Member
Join Date: Dec 2010
Location: Above ground, Walnut Creek, Ca
Posts: 6,681
Bikes: 8 ss bikes, 1 5-speed touring bike
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 86 Post(s)
Likes: 0
Liked 4 Times
in
4 Posts
after a number of years of trying to "make do", i went to my LBS and tried to buy a chainring wrench. the mechanic GAVE ME his. he said they were cheap... i don't doubt him. it's just a piece of 1/16", on a good day, stamped steel that's been bent in a couple of places. pretty flimsy, but usually works.
BTW, when i don't have the tool handy, i've managed from time to time to get them off, and on, by vigorously turning the male portion while imparting a lot of sideways torque. the friction heats up the female portion causing her () to bind in the spider.
BTW, when i don't have the tool handy, i've managed from time to time to get them off, and on, by vigorously turning the male portion while imparting a lot of sideways torque. the friction heats up the female portion causing her () to bind in the spider.
Last edited by hueyhoolihan; 02-28-14 at 05:22 PM.
#6
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
A wide blade screwdriver should span the slots in the nuts. The proper tool is the Park or similar spanner.
#7
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,720
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5788 Post(s)
Liked 2,581 Times
in
1,431 Posts
after a number of years of trying to "make do", i went to my LBS and tried to buy a chainring wrench. the mechanic GAVE ME his. he said they were cheap... i don't doubt him. it's just a piece of 1/16", on a good day, stamped steel that's been bent in a couple of places. pretty flimsy, but usually works. .
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
#8
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,720
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5788 Post(s)
Liked 2,581 Times
in
1,431 Posts
A wide blade screwdriver often works, but just as often doesn't because the screw extends beyond the depth of the slot. You need to use a blade wide enough, then grind out the center, so only two small edges of the blade can fit around the screw.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
#10
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,720
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5788 Post(s)
Liked 2,581 Times
in
1,431 Posts
Yes, if you have the right one (the discontinued red one), and a very steady hand. The current crop's pins are too fat.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
#11
Senior Member
Removing chainring bolts?
I have used a snap ring plier with some success. Sometimes you can find them in the cheapy bin at your hardware store.
#14
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
Yeah, some do and some don't. The Shimano cranks of several vintages I have all have the bolts short enough that a wide screwdriver blade can span the nut's notches without interference. I've had others that don't work.
#15
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times
in
723 Posts
+1, Park CNW-2, the right tool for the job. Grease the threads to ease removing them the next time.
#16
Senior member
Join Date: Oct 2004
Location: Oakville Ontario
Posts: 8,118
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 943 Post(s)
Liked 658 Times
in
371 Posts
This is one that Truvative got right. Their chainring bolts take a 5mm hex wrench on the front and 6mm on the back. Wonder why a simple idea like that took so long to come up with.
#17
rebmeM roineS
Join Date: Jan 2006
Location: Metro Indy, IN
Posts: 16,216
Bikes: Bacchetta Giro A20, RANS V-Rex, RANS Screamer
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 653 Post(s)
Liked 347 Times
in
226 Posts
Works like a charm.
__________________
Bacchetta Giro A20, RANS V-Rex, RANS Screamer
Bacchetta Giro A20, RANS V-Rex, RANS Screamer
#19
Not quite there yet
Join Date: Feb 2013
Location: Monkey Bottom, NC
Posts: 999
Bikes: A bunch of old steel bikes + an ICE trike
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
Used to be these wrenches were included with each crankset. They work, but not real well. This is what you need:
https://www.amazon.com/Var-Combined-T.../dp/B004YJ2X7Q
https://www.amazon.com/Var-Combined-T.../dp/B004YJ2X7Q
#21
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
Used to be these wrenches were included with each crankset. They work, but not real well. This is what you need:
https://www.amazon.com/Var-Combined-T.../dp/B004YJ2X7Q
https://www.amazon.com/Var-Combined-T.../dp/B004YJ2X7Q
#22
Warehouse Monkey
Thread Starter
Join Date: Jul 2008
Location: Lebanon Co., Pennsylvania
Posts: 1,604
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 305 Post(s)
Likes: 0
Liked 7 Times
in
2 Posts
Just went to the harware store and bought a snap-ring pliers. We'll see what happens.
__________________
'10 Specialized Hardrock
'10 Specialized Hardrock
#23
Warehouse Monkey
Thread Starter
Join Date: Jul 2008
Location: Lebanon Co., Pennsylvania
Posts: 1,604
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 305 Post(s)
Likes: 0
Liked 7 Times
in
2 Posts
Bent the pins on the pliers. I took the crank off and have it soaking in WD-40 for a bit. Next I take some heat to it break the bond.
__________________
'10 Specialized Hardrock
'10 Specialized Hardrock
#24
Your cog is slipping.
Used to be these wrenches were included with each crankset. They work, but not real well. This is what you need:
https://www.amazon.com/Var-Combined-T.../dp/B004YJ2X7Q
https://www.amazon.com/Var-Combined-T.../dp/B004YJ2X7Q
This works just as well for occasional use if the Park Tool spanner isn't cutting it.
#25
Senior Member
Join Date: Jan 2012
Location: Spokane, WA
Posts: 2,243
Bikes: Specialized Sequoia Elite/Motobecane Fantom Cross Team Ti/'85 Trek 520
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Likes: 0
Liked 3 Times
in
3 Posts
Man, on all the cranksets (dozens, more?) I have disassembled over the last couple of years at the co-op, I have never had an issue taking the bolts off chainrings with nothing more than the allen key. I must just be lucky.