Take apart this reflector
#1
Junior Member
Thread Starter
Join Date: Sep 2013
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Take apart this reflector
How do I take apart this bicycle reflector? I have two of them. I want to add led lights into them.
The reflectors are from a sears spaceliner. Do you think it will be better for me to sell them?
The reflectors are from a sears spaceliner. Do you think it will be better for me to sell them?
#2
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times
in
723 Posts
It looks like the aluminum base has been crimped around the red plastic part and you will likely destroy it getting it apart.
#5
Senior Member
Why not drill numbers of holes into the aluminum base you need for the lights then fill the holes with silicone when you are done .
#6
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,720
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5788 Post(s)
Liked 2,581 Times
in
1,431 Posts
It's a nice reflector. It would be a shame to destroy it to make a poor light (reflector and light lens optics are different). Keep the reflector, and make or buy a light.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
#8
Mechanic/Tourist
Agreed - parts for older bikes are hard to find. Sell the reflectors and use the money to buy LED lights.
#9
It's MY mountain
Join Date: Sep 2006
Location: Mt.Diablo
Posts: 10,002
Bikes: Klein, Merckx, Trek
Mentioned: 70 Post(s)
Tagged: 0 Thread(s)
Quoted: 4338 Post(s)
Liked 2,981 Times
in
1,617 Posts
Before you do anything, see if you can find a type of light that would fit in there; looks to me too small for any kind of light and battery system to fit inside. You might consider an external battery, so that would require drilling the aluminum base for the wires anyway.
#10
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
Decent LED taillights are so inexpensive and so much better than jury-rigging your reflector that it's not worth the time or cost to modify it.
They are self contained, run on AAA batteries that last a long time and have both steady and slashing modes. This one is only $7 and is better than anything you could make: https://www.nashbar.com/bikes/Product...42_-1___202551 For a bit more money you can get a super bright taillight that can be seen for blocks.
They are self contained, run on AAA batteries that last a long time and have both steady and slashing modes. This one is only $7 and is better than anything you could make: https://www.nashbar.com/bikes/Product...42_-1___202551 For a bit more money you can get a super bright taillight that can be seen for blocks.
Thread
Thread Starter
Forum
Replies
Last Post
Binky
Classic and Vintage Bicycles: Whats it Worth? Appraisals.
11
12-21-14 09:51 PM