Go Back  Bike Forums > Bike Forums > General Cycling Discussion
Reload this Page >

protecting my lock?

Search
Notices
General Cycling Discussion Have a cycling related question or comment that doesn't fit in one of the other specialty forums? Drop on in and post in here! When possible, please select the forum above that most fits your post!

protecting my lock?

Thread Tools
 
Search this Thread
 
Old 05-05-09, 01:14 PM
  #1  
everyday I'm hustlin'
Thread Starter
 
brandonspeck's Avatar
 
Join Date: Aug 2008
Location: Portland, OR
Posts: 453

Bikes: Surly Crosscheck, Surly Steamrolla

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
protecting my lock?

Hey,

I was just curious about some measures I could do to keep my U-Lock in good condition. My old kryptonite lock seized up, and since then I upgraded to a Kryptonite Evolution. It rained a bit the other day, and the inside already looks like it's rusting up a little. I'm moving to Portland and I'm getting all my bikes sprayed with frame saver, I was just curious if there was anything similar for locks, or if I actually even needed anything.

thanks!
brandonspeck is offline  
Old 05-05-09, 01:25 PM
  #2  
Senior Member
 
Join Date: Jan 2008
Posts: 284
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I just drop some heavy oil-based lube (finish line wet lube does well) in the lock cylinder and on the surface of the shackle where enters the crossbar. Mine's been outside all winder and is doing fine, so i think it's working...
alpacalypse is offline  
Old 05-05-09, 09:49 PM
  #3  
Year-round cyclist
 
Join Date: Apr 2002
Location: Montréal (Québec)
Posts: 3,023
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 2 Times in 2 Posts
I made a protective flap with an old piece of bicycle tube. So far, so good.
Michel Gagnon is offline  
Old 05-05-09, 09:52 PM
  #4  
S E Michigan
 
Join Date: Jun 2008
Posts: 431
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
If you drop any good oil or lock lube in it regular it should be fine ! If your in rain a LOT I would do it once a week if you had problems in the past just my 2 cents . I hardly ever ride in rain or get mine wet so never had a problem and I oil mine anyway every now and then . But I oil all my locks on my tool boxes gates bikes what have you regular . I got locks been out in Michigan weather 40 yrs doing just fine gotta take care of things is all .

Or you could Red Green it and put a piece a Duct tape over the hole :O)))
pipes is offline  
Old 05-06-09, 12:44 PM
  #5  
DancesWithSUVs
 
dynaryder's Avatar
 
Join Date: Apr 2005
Location: Griffin Cycle Bethesda,MD
Posts: 6,983
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 7 Post(s)
Likes: 0
Liked 2 Times in 2 Posts
Whenever I lock up in the rain,when I get home I open the lock and put it on the heater in winter or stove stop(I have pilot lights for the burners that keep the stove top warm) in summer to let it dry out. DO NOT use WD40 as this will just make a mess,I found this out the hard way. If you're really concerned,you could always wrap a plastic bag around the lock bar to keep it dry.
__________________

C'dale BBU('05 and '09)/Super Six/Hooligan8and 3,Kona Dew Deluxe,Novara Buzz/Safari,Surly Big Dummy,Marin Pt Reyes,Giant Defy 1,Schwinn DBX SuperSport,Dahon Speed Pro TT,Brompton S6L/S2E-X
dynaryder is offline  
Old 05-06-09, 10:50 PM
  #6  
Senior Member
 
Join Date: Jul 2007
Location: Melbourne, Australia
Posts: 224

Bikes: Giant CRX

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by alpacalypse
I just drop some heavy oil-based lube (finish line wet lube does well) in the lock cylinder and on the surface of the shackle where enters the crossbar. Mine's been outside all winder and is doing fine, so i think it's working...
I don't think you're supposed to use oil of any description in a lock. It can polymerise and jam the tumblers. Graphite is usually used in locks -- comes in puffer packs specially intended for locks at any hardware store.

Having said that I usually use WD40 as it's thin and, as we chain lube experts know, doesn't 'stick'.
bmorey is offline  
Old 05-06-09, 11:26 PM
  #7  
Senior Member
 
Join Date: Aug 2006
Posts: 998
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Graphite is great for locks... if they don't get water and gunk inside them, otherwise, it turns into a mess.

For the part that secures the shackle, I'd recommend a heavier oil or a grease. For the lock, I recommend a Teflon lube. Radio shack sells this (PTFE is the generic name for Teflon), and this does a good job. Here in Texas, I use it yearly, but in more rainy climates, I'd use it perhaps quarterly.
mlts22 is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.