80mm Tubes for my ZIPP Wheels -- what to consider?
#1
Senior Member
Thread Starter
80mm Tubes for my ZIPP Wheels -- what to consider?
Thinking of going with 80mm Tubes for my ZIPP Wheels. Right I have the valve extenders which i have gotten used to. But it is still bit of a pain to put extra air in the the tubes at times using the valve extenders.
Thinking of going with the 80mm tubes Contennential makes
Would I have any problems with using them? eg. stem banging around? etc etc?
thanks for input before i make this transition?
Thinking of going with the 80mm tubes Contennential makes
Would I have any problems with using them? eg. stem banging around? etc etc?
thanks for input before i make this transition?
#2
So it is
Join Date: Sep 2008
Location: Westminster, CO
Posts: 21,349
Bikes: Luzerne, 684, Boreas, Wheelhouse, Alize©®, Bayamo, Cayo
Mentioned: 246 Post(s)
Tagged: 1 Thread(s)
Quoted: 11402 Post(s)
Liked 4,759 Times
in
2,768 Posts
I use them with no issue at all. BDop Valvinators will keep the rattling of the stem down.
#4
Senior Member
Join Date: Dec 2009
Location: Houston, TX
Posts: 28,682
Bikes: 1990 Romic Reynolds 531 custom build, Merlin Works CR Ti custom build, super light Workswell 066 custom build
Mentioned: 109 Post(s)
Tagged: 1 Thread(s)
Quoted: 6556 Post(s)
Likes: 0
Liked 58 Times
in
36 Posts
+1 on the Valvinators from BDop Cycling. I have also used the 80 mm stems with no problem. You can also wrap the stem in electrical tape where it goes through the hole in the rim. If you don't want the Valvinators electrical tape works almost as good to cushion the valve hole also. Better than extenders for sure.
#5
pan y agua
Join Date: Aug 2005
Location: Jacksonville
Posts: 31,303
Bikes: Willier Zero 7; Merlin Extralight; Calfee Dragonfly tandem, Calfee Adventure tandem; Cervelo P2; Motebecane Ti Fly 29er; Motebecanne Phantom Cross; Schwinn Paramount Track bike
Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 1447 Post(s)
Liked 727 Times
in
372 Posts
80mm Tubes for my ZIPP Wheels -- what to consider?
Which zipps? 80mm stems are fine for 404's. Too short for 808
__________________
You could fall off a cliff and die.
You could get lost and die.
You could hit a tree and die.
OR YOU COULD STAY HOME AND FALL OFF THE COUCH AND DIE.
You could fall off a cliff and die.
You could get lost and die.
You could hit a tree and die.
OR YOU COULD STAY HOME AND FALL OFF THE COUCH AND DIE.
#6
well hello there
Join Date: May 2005
Location: Point Loma, CA
Posts: 15,430
Bikes: Bill Holland (Road-Ti), Fuji Roubaix Pro (back-up), Bike Friday (folder), Co-Motion (tandem) & Trek 750 (hybrid)
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 503 Post(s)
Liked 336 Times
in
206 Posts
and 60mm stems are fine for the 303s.
__________________
.
.
Two wheels good. Four wheels bad.
.
.
Two wheels good. Four wheels bad.
#7
Senior Member
Thread Starter
I noticed someone mentioned about using the Lite Tubes. Any problems with the Lite tubes from the air coming out during a ride?
would the lite tubes be just as durable as regular tubes?
would the lite tubes be just as durable as regular tubes?
#8
Mr. Dopolina
Join Date: May 2007
Location: Taiwan
Posts: 10,217
Bikes: KUUPAS, Simpson VR
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 149 Post(s)
Liked 117 Times
in
41 Posts
I suggest looking for tubes with remove able cores in any length and getting an adaptor that allows the core to be screwed in the top so it operates like a regular tube. That way you can find a replacement tube no matter where you are and stem length won't matter.
#9
Senior Member
Join Date: Nov 2012
Location: Palm Desert, CA
Posts: 2,504
Bikes: Speedvagen Steel
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 429 Post(s)
Liked 248 Times
in
156 Posts
Well if you're talking about my Bontrager Race XL it's just the name of their model (they also have an xXl Light which I used with my older wheels but they don't make them in 80mm stems). No problems at all, they're just standard tubes but lighter than many.
Last edited by robbyville; 03-29-14 at 07:53 AM.
#10
Senior Member
Join Date: Nov 2012
Location: Palm Desert, CA
Posts: 2,504
Bikes: Speedvagen Steel
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 429 Post(s)
Liked 248 Times
in
156 Posts
No, they're not as durable.
I suggest looking for tubes with remove able cores in any length and getting an adaptor that allows the core to be screwed in the top so it operates like a regular tube. That way you can find a replacement tube no matter where you are and stem length won't matter.
I suggest looking for tubes with remove able cores in any length and getting an adaptor that allows the core to be screwed in the top so it operates like a regular tube. That way you can find a replacement tube no matter where you are and stem length won't matter.
#11
Mr. Dopolina
Join Date: May 2007
Location: Taiwan
Posts: 10,217
Bikes: KUUPAS, Simpson VR
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 149 Post(s)
Liked 117 Times
in
41 Posts
Be sure to get an alloy tool so you can use it more than on e. The plastic tools are useless and utterly disposable.
Thread
Thread Starter
Forum
Replies
Last Post
MDI
Bicycle Mechanics
11
02-27-12 08:58 PM