How to cut handlebars
#1
Junior Member
Thread Starter
Join Date: May 2008
Posts: 16
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
How to cut handlebars
I was wondering how hard it is to cut a pair of drop handle bars into bullhorn, mainly how do I do it? How do you re-grip your bars, is there a pattern or should I just go for it?
#3
surly old man
Join Date: Sep 2006
Location: Carlisle, PA
Posts: 3,392
Bikes: IRO Mark V, Karate Monkey half fat, Trek 620 IGH, Cannondale 26/24 MTB, Amp Research B3, and more.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 46 Post(s)
Likes: 0
Liked 42 Times
in
18 Posts
Pipe cutter, ftw
__________________
Cross Check Nexus7, IRO Mark V, Trek 620 Nexus7, Karate Monkey half fat, IRO Model 19 fixed, Amp Research B3, Surly 1x1 half fat fixed, and more...
--------------------------
SB forever
Cross Check Nexus7, IRO Mark V, Trek 620 Nexus7, Karate Monkey half fat, IRO Model 19 fixed, Amp Research B3, Surly 1x1 half fat fixed, and more...
--------------------------
SB forever
#4
Don't Hate.
Join Date: May 2008
Posts: 625
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
OK, put the bars on your bike. Then put some grips on there and figure out about how close inwards you want them to be. mark it at the ends of the grips. measure both sides so the marks are equally distant from the middle. leave them clamped in place (in your stem) to keep them still. cut straight down using a hack saw. file off the rough edges before putting grips on.
#5
:)
Join Date: Nov 2006
Location: duluth
Posts: 3,391
Bikes: '07 Pista, '09 Fantom Cross Uno, '8? Miyata, '67 Stingray, '0? Zoo mod trials, Tallbike, Chopper, '73 Schwinn Collegiate, '67 Triumph Chopper, '69 CB350, '58 BSA Spitfire, '73 CB450
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
pipe cutter > sawzall > hacksaw
at least from my experience.
at least from my experience.
#7
:)
Join Date: Nov 2006
Location: duluth
Posts: 3,391
Bikes: '07 Pista, '09 Fantom Cross Uno, '8? Miyata, '67 Stingray, '0? Zoo mod trials, Tallbike, Chopper, '73 Schwinn Collegiate, '67 Triumph Chopper, '69 CB350, '58 BSA Spitfire, '73 CB450
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
donno. Pipe cutter takes a min. or two longer than the hacksaw and sawzall for me, but doesn't leave a ton of metal dust lying around, or wake up the neighbors.
#8
unofficial
Join Date: Apr 2008
Location: san rafael, CA
Posts: 1,054
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
measure twice, cut once...
i used a hacksaw b/c it is more likely to be lying around than a pipe cutter, use whats available
i used a hacksaw b/c it is more likely to be lying around than a pipe cutter, use whats available
#9
Banned.
Join Date: May 2007
Location: Astoria NY
Posts: 184
Bikes: fixed iro jamie roy
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
the key to the pipe cutters is to tighten the blade down every few spins. it will be tough to turn so grab the blade tightening knob with pliers and twist it. then just spin the whole thing a couple times and then tighten the blade again. dont waste time spinning the whole thing forever without constantly bring down the blade.
#10
Strong with the Fred
Join Date: May 2008
Location: Dallas, TX
Posts: 970
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
I highly recommend pipe cutters. They take just a little longer but make for a very clean and even cut. You won't even have to file the rough edges off the handlebar.
Ernest
Ernest
#11
Senior Member
Join Date: Feb 2005
Location: San Francsico, CA
Posts: 324
Bikes: Schwinn Voyageur '89
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 10 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
word. pipecutters won't give you jagged edges. You just need to know how to use them.
#12
Senior Member
Join Date: Nov 2007
Location: MKE, WI
Posts: 52
Bikes: Alien, Fuji Track, Eight Inch Scrambler
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Also, it is useful to use the portion of the bar removed first as a template of sorts for the opposite side.
#14
Wrathchild
Join Date: Sep 2007
Location: Boston
Posts: 12
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Pipe cutter probably wont work on drops if you are chopping them into bull horns because of the curve. just food for thought...
#15
Senior Member
Join Date: Aug 2007
Location: the land of ice and snow
Posts: 999
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
If you're cutting at a point in the curve, it's nearly impossible to measure both sides accurately and to the exact same point. Take the removed portion of the bar and tape it on the other side (easier than trying to hold it steady while making sure it's perfectly lined up) to make the mark for cutting.
Oh yea, and pipe cutters are great.
#16
surly old man
Join Date: Sep 2006
Location: Carlisle, PA
Posts: 3,392
Bikes: IRO Mark V, Karate Monkey half fat, Trek 620 IGH, Cannondale 26/24 MTB, Amp Research B3, and more.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 46 Post(s)
Likes: 0
Liked 42 Times
in
18 Posts
j
__________________
Cross Check Nexus7, IRO Mark V, Trek 620 Nexus7, Karate Monkey half fat, IRO Model 19 fixed, Amp Research B3, Surly 1x1 half fat fixed, and more...
--------------------------
SB forever
Cross Check Nexus7, IRO Mark V, Trek 620 Nexus7, Karate Monkey half fat, IRO Model 19 fixed, Amp Research B3, Surly 1x1 half fat fixed, and more...
--------------------------
SB forever
#19
Hello.
Join Date: Jun 2005
Location: West Seattle
Posts: 2,902
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
the key to the pipe cutters is to tighten the blade down every few spins. it will be tough to turn so grab the blade tightening knob with pliers and twist it. then just spin the whole thing a couple times and then tighten the blade again. dont waste time spinning the whole thing forever without constantly bring down the blade.
#21
Heck yes.
Join Date: Jun 2007
Location: Phila-ila-delphia
Posts: 426
Bikes: Saint Tropez, Shogun
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#22
No plan.
Join Date: May 2007
Location: PA
Posts: 2,743
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
It doesn't need to be perfectly straight if you feel like filing it down afterwards. I think a dremel with an experienced user and cut off disk would work fine.... but in the end you're saving a few minutes, creating a ****ton of metal dust. just use a pipe cutter and do it right, no mess, in the first place.
#24
Junior Member
Thread Starter
Join Date: May 2008
Posts: 16
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I did it. The handlebars were of a smaller drop, so I'm brakeless for the moment. But, I think I'm gonna give the handlebars I cut to my friend for a pair of nitto ones. It works perfect he doesn't need brakes for his skill level, I still prefer to have them for me. The pipe cutter won out. It took about 5 minutes total.
#25
Ths Hipstr Kills Masheenz
Join Date: Oct 2006
Location: seattle
Posts: 8,542
Bikes: tirove
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 3 Times
in
3 Posts
dremel would be expensive and time consuming(multiple wheels and difficult)... hacksaw is not easy but it will be better than a pipe cutter because you can get the angle you want. i did mine with a hacksaw.