homemade rim strip easy
09-13-23, 06:48 AM
#1
Full Member
Thread Starter
Join Date: Dec 2006
Posts: 428
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Likes: 0
Liked 4 Times
in
4 Posts
homemade rim strip easy
I was rehabbing a really old bike yesterday and was out of rim strips and didn't feel like running to the bike store so I made one. Took about 10 minutes. I took and old innertube which most people have or can get free from any bike shop. I hooked it to my vise so I could easily stretch it out and cut it. Then I cut a long skinny strip from it being careful to follow the seam lines so it was straight. Then I stretched the strip along the wheel to get correct length allowing 1" extra. I took some thread and sewed the overlapping one inch with a few quick stitches and punched a valve hole with my paper punch. Voila worked fine and stronger than the flimsy usual rim strips.
Likes For cmcanulty:
09-13-23, 07:38 AM
#2
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 37,892
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 134 Post(s)
Tagged: 1 Thread(s)
Quoted: 5351 Post(s)
Liked 1,785 Times
in
1,013 Posts
I guess we all define easy differently.
If I need rim strips or tape, I make the effort to hike upstairs to the bathroom, open the cabinet and swipe the roll of cloth surgical tape from the first aid supply.
The hardest part is remembering to replace it.
If I need rim strips or tape, I make the effort to hike upstairs to the bathroom, open the cabinet and swipe the roll of cloth surgical tape from the first aid supply.
The hardest part is remembering to replace it.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
“Never argue with an idiot. He will only bring you down to his level and beat you with experience.”, George Carlin
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
“Never argue with an idiot. He will only bring you down to his level and beat you with experience.”, George Carlin
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
Likes For FBinNY:
09-13-23, 08:50 AM
#3
Senior Member
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,603
Bikes: Fuji Touring, Novara Randonee
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2432 Post(s)
Liked 1,746 Times
in
1,092 Posts
I'll give O.P. cheap, but I have to agree with FBinNY on easy.
Really easy would be having the spare rim tape float up to the top of my spare parts box when I need it.
Really easy would be having the spare rim tape float up to the top of my spare parts box when I need it.
Likes For pdlamb:
09-13-23, 09:00 AM
#4
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 8,447
Bikes: '70s - '80s Campagnolo
Mentioned: 91 Post(s)
Tagged: 0 Thread(s)
Quoted: 3678 Post(s)
Liked 6,077 Times
in
3,023 Posts
Rubber is too bulky for some tight fitting tires. I use two layers of 10mm kapton tape from eBay. Super inexpensive.
Likes For SurferRosa:
09-13-23, 10:24 AM
#5
Senior Member
Join Date: Jul 2013
Location: Missouri
Posts: 2,646
Bikes: Giant Propel, Cannondale SuperX, Univega Alpina Ultima
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 648 Post(s)
Liked 391 Times
in
231 Posts
Rim strips are cheap to begin with. I'd rather spring for an extra bick or two, be able to thrown them on in 10 seconds and not worry about flatting because my homemade strip gave up the ghost at an inopportune time.
__________________
Formerly fastest rider in the grupetto, currently slowest guy in the peloton
Formerly fastest rider in the grupetto, currently slowest guy in the peloton
Likes For bbbean:
09-13-23, 01:03 PM
#6
Senior Member
Join Date: Jul 2015
Location: NW Oregon
Posts: 2,972
Bikes: !982 Trek 930R Custom, Diamondback ascent with SERIOUS updates, Fuji Team Pro CF and a '09 Comencal Meta 5.5
Mentioned: 15 Post(s)
Tagged: 1 Thread(s)
Quoted: 1294 Post(s)
Liked 732 Times
in
530 Posts
one problem with using an inner tube as a rim band... Spokes poke holes in INNER TUBES, which is why we should all install Actual Rim strips.... or Medical bandage tape... 
Likes For maddog34:
09-13-23, 02:34 PM
#7
Senior Member
Join Date: Mar 2022
Location: Missoula MT
Posts: 1,237
Bikes: Handsome xoxo, Serotta atx, Canyon Endurace CF8
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 541 Post(s)
Liked 1,279 Times
in
581 Posts
back in my day we used packing tape. I still am using a wheel from the early 90's that has had the same piece of packing tape on it since probably 1993.
09-13-23, 02:42 PM
#8
bOsscO
Join Date: May 2006
Location: Vancouver
Posts: 727
Bikes: 2015 Norco Search S1, 93 Mongoose IBOC COMP
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 282 Post(s)
Liked 336 Times
in
203 Posts
I've used red electricians tape with good success. Not sure if it's stronger than standard black electricians tape...
09-13-23, 05:38 PM
#9
Senior Member
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,244
Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano
Mentioned: 32 Post(s)
Tagged: 0 Thread(s)
Quoted: 889 Post(s)
Liked 524 Times
in
349 Posts
+1 but I now have three different widths of Kapton tape for various rims... it adds up. Works great, however.
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.
Likes For tiger1964:
09-13-23, 10:27 PM
#10
Sr Member on Sr bikes
Likes For _ForceD_:
09-13-23, 11:32 PM
#12
Senior Member
Join Date: May 2010
Location: Bastrop Texas
Posts: 4,144
Bikes: Univega, Peu P6, Peu PR-10, Ted Williams, Peu UO-8, Peu UO-18 Mixte, Peu Dolomites
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 803 Post(s)
Liked 1,378 Times
in
885 Posts
That's allot of work. Its gonna work well...
I use High Temp Wiring Loom Harness Self-Adhesive Felt Cloth Electrical Tape (Amazon). Its cheap. I keep several rolls in the beer frig and no longer worry about having the right size rim strip.
It also works good for Bar Tape.
Man... I am such a cheap bastard too...
I use High Temp Wiring Loom Harness Self-Adhesive Felt Cloth Electrical Tape (Amazon). Its cheap. I keep several rolls in the beer frig and no longer worry about having the right size rim strip.
It also works good for Bar Tape.
Man... I am such a cheap bastard too...
__________________
No matter where your at... There you are... Δf:=f(1/2)-f(-1/2)
09-14-23, 06:34 AM
#13
Senior Member
Join Date: Jan 2013
Posts: 2,573
Bikes: too many sparkly Italians, some sweet Americans and a couple interesting Japanese
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 533 Post(s)
Liked 500 Times
in
364 Posts
Never had a problem with two layers of cheap 10mm kapton tape which stays in my bike tool box.
09-15-23, 03:23 PM
#14
Senior Member
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,652
Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque
Mentioned: 103 Post(s)
Tagged: 0 Thread(s)
Quoted: 2203 Post(s)
Liked 2,553 Times
in
1,398 Posts
I am still a velox cloth tape only guy for tubed setups
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Likes For squirtdad:
09-15-23, 05:14 PM
#15
Expired Member
Join Date: Jun 2007
Location: TN
Posts: 11,314
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 3577 Post(s)
Liked 5,158 Times
in
2,620 Posts
I'm with maddog on this. The inner tube might look the part but there's nothing to keep it from poking into the spoke hole like ... an inner tube.
Likes For shelbyfv:
09-16-23, 12:23 PM
#16
Senior Member
Join Date: May 2005
Location: SFBay
Posts: 2,333
Bikes: n, I would like n+1
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 127 Post(s)
Likes: 0
Liked 131 Times
in
106 Posts
While I don’t prefer them, I’ve used a lot of rubber rim strips in the past. They aren’t much different than a tube section. They also fail for the same reason, but take several years to do so unless your spokes are too long. Other than Velox I’ve used several kinds of tape, generally without issue. It’s even easier on double walled rims where you just have to bridge the holes.
09-18-23, 06:10 AM
#17
Senior Member
Cloth electrical tape. An inner tube as a rim strip is asking for a flat from a spokehead in all but the lowest pressure rarely used wheels.
09-19-23, 08:49 AM
#18
Hello
Fiberglass Filament tape
To the OP, Kudos, for a low/no budget solution, and making things worth, with what you got.
09-19-23, 10:54 AM
#19
Rhapsodic Laviathan
I've had wheels where the previous owner used duct tape. I usually use electrical tape in a quick need of a rim strip. I was at the co-op last month and they didn't have any, so I used a rubber rim strip on top of the rubber rim strip on one wheel.
09-19-23, 12:34 PM
#20
Senior Member
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,513
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 802 Post(s)
Liked 950 Times
in
681 Posts
Yes to packing tape (with fiberglass filament). It has no stretch. Is, latitudinally tear resistant. Buy a wide roll as it is easy to tear straight longitudinally, so that one roll serves different rim bed widths (perfect custom width every time).
To the OP, Kudos, for a low/no budget solution, and making things worth, with what you got.
To the OP, Kudos, for a low/no budget solution, and making things worth, with what you got.
10-18-23, 11:14 AM
#21
Cantilever believer
Join Date: Nov 2021
Location: Phoenix, AZ
Posts: 1,242
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 409 Post(s)
Liked 1,363 Times
in
648 Posts
At Recycle Your Bicycle, we go through rim strips by the hundreds in just one weekend, and we just heard our distributor is out of stock on some sizes UFN.
I've tried making rim strips out of old (next size down) tubes, but my experience in trying to cut or punch a Schrader-size hole without creating a plane of weakness that eventually tears has not been good. We can go to the ol' "3 loops of inexpensive electrician's tape", but were hoping there might be a better option. And no, our budget is nowhere near that which would allow the use of "real" cloth rim tape for hundreds of bikes.
Do you use the 3/5", 3/4", or 1" width? The 3/4" (18 mm) looks like it would be the most useful width. By my calculations, we could do about eight 26" rims per roll.
I've tried making rim strips out of old (next size down) tubes, but my experience in trying to cut or punch a Schrader-size hole without creating a plane of weakness that eventually tears has not been good. We can go to the ol' "3 loops of inexpensive electrician's tape", but were hoping there might be a better option. And no, our budget is nowhere near that which would allow the use of "real" cloth rim tape for hundreds of bikes.
Do you use the 3/5", 3/4", or 1" width? The 3/4" (18 mm) looks like it would be the most useful width. By my calculations, we could do about eight 26" rims per roll.
__________________
Richard C. Moeur, PE - Phoenix AZ, USA
https://www.richardcmoeur.com/bikestuf.html
Richard C. Moeur, PE - Phoenix AZ, USA
https://www.richardcmoeur.com/bikestuf.html
Likes For JanMM:
10-18-23, 02:24 PM
#23
Passista
Join Date: Jul 2005
Posts: 7,542
Bikes: 1998 Pinarello Asolo, 1992 KHS Montaña pro, 1980 Raleigh DL-1, IGH Hybrid, IGH Utility
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 849 Post(s)
Liked 674 Times
in
367 Posts
BITD we used to make rim strips with inner tubes, gluing the ends instead of sewing. Worked OK on single wall rims/low pressure tires, but not on double wall/high pressure, as the tube would force the strip into the spoke holes.
10-18-23, 02:41 PM
#24
Friendship is Magic
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,405
Bikes: old ones
Mentioned: 303 Post(s)
Tagged: 0 Thread(s)
Quoted: 25569 Post(s)
Liked 9,512 Times
in
6,618 Posts
At Recycle Your Bicycle, we go through rim strips by the hundreds in just one weekend, and we just heard our distributor is out of stock on some sizes UFN.
I've tried making rim strips out of old (next size down) tubes, but my experience in trying to cut or punch a Schrader-size hole without creating a plane of weakness that eventually tears has not been good. We can go to the ol' "3 loops of inexpensive electrician's tape", but were hoping there might be a better option. And no, our budget is nowhere near that which would allow the use of "real" cloth rim tape for hundreds of bikes.
Do you use the 3/5", 3/4", or 1" width? The 3/4" (18 mm) looks like it would be the most useful width. By my calculations, we could do about eight 26" rims per roll.
I've tried making rim strips out of old (next size down) tubes, but my experience in trying to cut or punch a Schrader-size hole without creating a plane of weakness that eventually tears has not been good. We can go to the ol' "3 loops of inexpensive electrician's tape", but were hoping there might be a better option. And no, our budget is nowhere near that which would allow the use of "real" cloth rim tape for hundreds of bikes.
Do you use the 3/5", 3/4", or 1" width? The 3/4" (18 mm) looks like it would be the most useful width. By my calculations, we could do about eight 26" rims per roll.
...Kapton tape is pretty cheap, and it comes in various widths, in bulk rolls. I used to use Velox, but Kapton tape is cheaper, and it works a little better.
__________________
Likes For 3alarmer:
10-18-23, 02:50 PM
#25
Senior Member
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,393
Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder
Mentioned: 121 Post(s)
Tagged: 0 Thread(s)
Quoted: 4446 Post(s)
Liked 3,533 Times
in
2,297 Posts
That inner tube strip might expand into the spoke holes in box section rims. I thought the rim strip's job was to prevent that. (Big fan of the Velox strips and their shelf life seems to be near forever so I have no excuse for not being stocked up. Except during COVID, choices were so slim I bought wide rolls knowing I was going to slice them to size with a sharp knife.)
